Question about Chevrolet Impala

Open Question

Door rubbing on the ft fender, need adjustment left and right

Posted by on

3 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

countrysi248
  • 443 Answers

SOURCE: i need to adjust front left fender

this might be more than what you want to do but .. there is a bolt on the bottom of the fender near the door .. this is an important one to loosen.. you next loosen the one infront of the windshield .. which is top of the fender.. also there is one inside the door .. with door open look back in there you will see only one bolt there. Now you need to find a way to pull this fender back forward enough to pull it away from the door so you can operate the door properly.. We take the headlight assembly out and use a puller device to pull it back forward .. you can also tie this to a post or tree and lightly back up .. try this and see what you come up with .. tighten all bolts after you get it pulled forward or while you have it in a strain forward.. thanks jerry

Posted on Apr 26, 2009

KTMEXC250
  • 31 Answers

SOURCE: sounds like tire rub when turning right or left

It may be your power steering. Try checking the level of the power steering fluid. If you are not familiar with where this is check your owners manual and it will definitely tell you where it's located under the hood. If the fluid is at a good level it is most likely something to do with your wheel alignment. This can only be checked and serviced by a licenced motor mechanic or specialist alignment centre.

Good luck

Posted on Nov 11, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Adjusting left fromt door backwards


Doors aren't be adjusted front to back. If you need more clearance for the fender. Adjust the fender.

Apr 01, 2016 | Cars & Trucks

1 Answer

How do I adjust the drivers door on a 2006 pontiac montana SV6 air is leaking around the door.


Take the fender off. then loosen the door hinge bolts. Move the door left or right up or down in or out until the crack between the door and the pillar looks straight and even. Then do the same with the fender. Chances are the door hinges need replacing.

Oct 25, 2013 | 2006 Pontiac Montana SV6

1 Answer

Driver door rubs against fender, will not allow door to open and close properly . Its wear the skirt of the driver door exterior. Truck is a 2007 ss silverado


sounds like one of the door hinges may need to be adjusted or worn enough to either re-align the door or replace a hinge pin providing the fender hasn`t been hit or become mis-adjusted.

May 05, 2011 | Chevrolet Silverado 1500 Cars & Trucks

1 Answer

DS door is rubbing on front fender when opening and closing. How can I adjust door to keep from happening? 2007 2500 silverado HD (classic)


it is easier to to adjust the fender cause if you move the door it could cause you a huge headache tring to get it to line up at the latch and you could cause numorous wind noises and air leaks.

Dec 16, 2010 | 2007 Chevrolet Silverado 2500HD

1 Answer

Replace alternator


Remove or disconnect the following:
  • Negative battery cable
  • Right front wheel
  • Right fender splash shield
  • Accessory drive belt
NOTE The crankshaft pulley retainer has left-hand threads.

  • Crankshaft pulley
  • Alternator harness connectors
  • Alternator

eed945c.gif

Remove the crankshaft pulley to provide clearance—2002–04 3.0L


To install:
  1. Install or connect the following:
    • Alternator and tighten the fasteners to 18 ft. lbs. (25 Nm)
    • Alternator harness connectors
    NOTE The crankshaft pulley retainer has left-hand threads.

    • Crankshaft pulley and tighten to 74 ft. lbs. (100 Nm)
    • Accessory drive belt
    • Right fender splash shield
    • Right front wheel
    • Negative battery cable
  2. Start the engine and check for proper operation

May 12, 2010 | 2003 Ford Taurus

1 Answer

1994 Honda Accord 4 door. Fender removal to adjust door.


Should have kept going-it's just screws or bolts, but some are almost hidden-like front of fender and rear along door opening. Take off fender lining and look some more.
I sort of know what you mean-can be hard to get to the door hinges. have you tried like a universal joint in your ratchet and socket?

Mar 13, 2017 | Honda Accord Cars & Trucks

1 Answer

Door rubbing on front fender when opening and closing on my 2005 chevy trailblazer how do i adjust the door


At first check if the door hanger's are OK. This item is the first that quit his job on most SUV's and cars. Open your door to half, then try to lift the door up. If that happens, change the door hanger incl. 2 metal rings(one on top, one at the bottom) this part cost only some bucks. If you need to adjust the door, there are 2 screws on the body, this let the door slips front/rear, and -if your car is equipped with - there are 2 screws at the door, that let the door swing up and down. If it rubbs on the fender, take the doors backwards for only 2mm.

Oct 25, 2009 | 2005 Chevrolet TrailBlazer

1 Answer

1998 olds cutlass makes a rubbing noise when steering wheel is turned to the left or to the right.


Sounds like the plastic inner fender is loose, or hanging and the wheel is touching it while driving. While the car is parked, try turning the wheel all the way to the left, then look under the left fender, behind the wheel to see if there is anything hanging or in the way. If not then turn the wheel all the way to the right, and check under the right fender and wheel.

Jul 06, 2009 | 1998 Oldsmobile Cutlass

1 Answer

1991 ford tempo gl four door


there are 2 screws that adjust up/down & sideways. park 20 ft from garage door.Left - in a little & down a little. right - sown a little.

Feb 22, 2009 | 1992 Ford Explorer

1 Answer

I have a 93 escort wagon , that i love... it was hit in an accident... i bought a liitle parts car an need to replace parts.... does anyone have auto body part on the manuel?


I have done this for years and am familiar with these cars. The first thing to do is cut in your parts, by that I mean paint the inside edges of your door, fender and hood before you install them. The hood is a no brainer. four bolts probably ten millimeter. The fender is not very hard either, remove headlight and side marker and front bumper. The door needs to be disconnected under the dash and the wires pulled out before removal. Install the door and adjust it till it fits and closes properly, then the fender by lining up the body line before tightning into place. Before putting in the bolts along the top install your hood and align it with the back of the cowl so that it is even gap all the way across then adjust fender gap and tighten down. This will work perfect if your inner structure has not been bent or knocked over. Be glad to help further if you need it

Aug 29, 2008 | 1993 Ford Escort 4 Door

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

23 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8210 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...