Question about 2007 Chevrolet Impala LS Sedan New Cars

1 Answer

Brakes How to do the brakes is there any special tool need. Ect

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 341 Answers

Gm uses one of 3 tools to remove calipers 1- T-50 tork bit 2 3/8 hex scoket 3 13mm socket

Posted on Oct 21, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Check engine light came on got an error P0128 need to see a photo or diagram to know where my engine coolant temp sensor is, want to change it myself. Do I need a special tool to get the one end off/on? If...


most ect are located on the thermostat housing ..that is the piece where the upper radatior hose goes to....it will have a 1,2,or 3 wire connector to it and the ect should be brass in color....a 19mm deep socket or maybe even a 19mm wrench will remove this as long as there is room to reach it...u may have to remove some air box tubing to get to it....no special tools required

Jul 16, 2011 | GMC Envoy XL Cars & Trucks

1 Answer

Changed the front brakes and now I cant get the brake lines to hold pressure. Bleeder valves and caliper hoses are all tight. But now I have no brakes other than the e-brake. Help!


ACURA ANTI BRAKE SYSTEM.YOU NEED A ACURA SPECIAL TESTER O7HAJ - SGOO100Z.NEED SPECIAL WRENCH O7HAA-SGOO100 NEED TO RELIEVE PRESSURE IN THE ACCUMULATOR. THIS JOB FOR DEALERSHIP.YOU CANT MANUAL BLEED THIS BRAKE SYSTEM YOU NEED SPECIAL TOOLS TO BLEED.IF TRY TO BLEED WITHOUT RIGHT TOOLS YOU WILL DO MORE DAMAGE.

Jun 18, 2010 | 1992 Acura Vigor

1 Answer

Bleeding brakes, The front brakes will not bleed out


In order to bleed the brakes on this car u need a special tool that holds the ABS Hydraulic control units pop-it valves open, without this special tool that plugs into the ABS you can't bleed the air out of the ABS control valve module, u either have to have the dealer do this or someone who has a factory equivalent of the ABS special bleeding tool, Snap-On tools most likely makes these, they are horribly expensive.

Mar 30, 2010 | 1996 Land Rover Discovery

2 Answers

Any Special tools needed for brakes on 2004 Suzuki Verona


for the fronts all you need is a set of metric sockets and a ratchet,use a c clamp to push back the caliper piston.remove the caliper mount bracket and rotor is out reverse install. now for the back if rotors have emergency brake using the same pads then you will have to buy a special tool to help you screw in the caliper piston tool costs lees then ten dollars.small cube with universal pins on each side also to be used on other vehicles.

Jan 14, 2010 | 2004 Suzuki Verona

1 Answer

Do you need a special tool to change the rear brakes for a 2007 VW Jetta


yes, you need a special tool to screw the brake piston back into the caliper housing. this is do to your disc brake set up. tool is available from harbor freight at around 40 dollars.

Aug 22, 2009 | 2007 Volkswagen Jetta 2.5 Sedan

2 Answers

Is there any special tools to change the brakes on a 2000 lincoln ls


standard hand tools, remember to have the rotors turned by a machine shop.

May 26, 2009 | 2000 Lincoln LS

1 Answer

Brake spring installing.


you can purchase a special tool for brakes There is a special tool for the springs the two on the side of the horse shoe shape ones, and a special tool for the two ciccular ones on the side, One is a special type of pliers, and the other is a handle type driver tool



Melvin
St Louis

May 12, 2009 | 2007 Chevrolet Cobalt Coupe

2 Answers

Rear Brakes 2005 Jetta


im sorry bro i find that you needing special tools a load of bs. i may be wrong but i really really doubt it. brakes are easy. first locate the caliper and there should be 2 bolts holding that tight. loosen the top bolt and then take out the lower bolt from the caliper. the old pads should just fall out. remove the master cylinder cap. (the jug with brake fluid in it.) compress the piston replace the old pads and push the claiper back down on the rotor. tighten bolts back up pump the brakes till hard with the car off and then repeat for the other side.

Apr 28, 2009 | 2003 Volkswagen Jetta TDI

2 Answers

Rear Brakes on a 2002 GMC 2500HD.


skip8303, it's not the same, you need 18mm socket, t55 torx and alot of grunt.

Dec 11, 2008 | 2002 GMC Sierra 2500HD

1 Answer

BAck Brakes


DON'T FORCE THE PISTON WITH A C-CLAMP! On VW rear disc brakes you need to rotate the piston while pushing it back in otherwise you will mess up the caliper. You do need a special tool and can probably borrow one from an auto parts store. If not they can be purchased for ~$50. Look here:
http://www.dieselgeek.com/servlet/Detail?no=313

There are many other place to buy this so shop around.

Aug 10, 2008 | 2003 Volkswagen Jetta TDI

Not finding what you are looking for?
2007 Chevrolet Impala LS Sedan New Cars Logo

Related Topics:

87 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

60867 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6811 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...