Question about Pontiac 2000

1 Answer

Can't get the rotor back on after changing brakes it wont turn

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Genius:

    An expert who has answered 1,000 questions.

  • Pontiac Master
  • 1,249 Answers

Were you able to push the piston completely back into the caliper? Did you try turning the rotor before installing the caliper? If the rotor still does not turn, then the wheel bearing could be the problem...Hope this helps.

Posted on Mar 21, 2011

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

7 Answers

My 2000 Dodge caravan's brakes are screeching after I changed them. Its only been 2 months since I changed them and its becoming very annoying. Changed the brakes and brake pads.


did you apply the brake pad anti squeal grease it should be applied generously to back of brake pads & also where brake calipers where brake pads will travel as they wear in some cases hard lifetime brake pads usually bmw/other german vehicles will simply squeal unless you install softer &wont last as long but im sure that brake grease will solve your noise issue you should have got a small tube where you purchased the brake pads !

Apr 30, 2015 | 2000 Dodge Caravan

1 Answer

Front brake problems of 1998 dodge avenger


Sounds like the calipers are not fully disengaging. Re-inspect the brakes, make sure everything is clean, then check to make sure the calipers back off when the brake is released.They wont be loose but the rotor should turn freely. Did you replace the rotors or have them turned?

Oct 14, 2012 | 1998 Dodge Avenger

2 Answers

How do i get the rear rotors off a 2006 Jetta (2.5)? I've got the brake assembly off but the other/larger assemble wont budge. It seems to need to have two torx nuts removed but I've tried a T55 and its to...


Rear Brake Pads & Brake Rotor Replacement Volkswagen Jetta 2005 ...

2q==? 8:57 https://www.youtube.com/watch?v=31m24XZj79c
  1. Similar
Nov 11, 2014 - Uploaded by 2CarPros In this video we show how to replace the rear brake pads and rotor on a 2005-2010 Volkswagen Jetta ...

how to change rear brakes and rotors on a 2006 vw jetta value edition ...

2q==? 16:56 https://www.youtube.com/watch?v=KRn3npN6FMw Sep 11, 2017 - Uploaded by Adventures In Living link to pads: http://amzn.to/2jj8vcq link to rotors: http://amzn.to/2wWKpJe.

2006 VW Jetta rear brakes - YouTube

z? 4:10 https://www.youtube.com/watch?v=S0cdLClKA2c May 25, 2016 - Uploaded by Austin Brandt Quick way to get your rear brakes done without buying specialty brake tools. ... Replacing Rear Brakes on ...

MK5 Rear Rotors and Pads Removal and Install - YouTube

2q==? 32:33 https://www.youtube.com/watch?v=AvhufC_ctGo Jun 20, 2016 - Uploaded by scirockalot8v Tools and supplies: M14 Triple Square (12 point) 15mm and 13mm wrench/sockets Flathead Screwdriver Torx ... 2006 Jetta remove rear rotors Google Search




Dec 07, 2017 | 2006 Volkswagen Jetta

1 Answer

I recently changed my rear brakes on my 2005 trailblazer and had the rotors turned. Now i have a grinding noise when i get up to 15mph and while braking.


Hello sweetascanb3,

A common problem is the emergency brakes drag on the inside of the rotor. The solution is to back off the adjuster. Another possible item is the backing plate they rust and distort and rub against the rotor, bending the backing plate so it doesn't touch the rotor is a fix for that problem.

Regards,
netvan

Feb 24, 2011 | 2002 Chevrolet TrailBlazer

1 Answer

Changed my front brakes and rotors..ABS light came


did you knock off a wire on the sensor ,or even break the sensor unit when you changed the rotors..

Jul 11, 2010 | 2006 Chevrolet Colorado

1 Answer

Brake Vibration


Your front rotor's were no cut right, there wrap so when you brake you feel that out of roundes, take your car back and have them cut the rotor's right, make sure they mic the rotor's to get a mim thickness or rotor will wrap again, if tis thin rotor's will have to be replace.

May 20, 2010 | 1998 Toyota 4Runner

3 Answers

I have a 2006 F150, that needs a front brakes job, I bough the pads,but they told that I need to buy the hole rotor is that true


You do not need to buy the whole rotor, unless your rotors are shot.
Most brake places will not change brake pads unless you also have your rotors machined or replaced, which makes them about $250 in extra profit... go figure heh?!
anyways, its a good idea to machine your rotors when you replace your pads, they will work better, they will last longer, and you wont feel any movement in the pedal when you are hard braking.
If your rotors are shot, you will need to get those replaced, if you ignore bad rotors, you will eat through your brake pads in a matter of months or even weeks, you wont have half the stopping power you should, if you need to brake really hard it will feel like you are going 40mph on a giant washboard, and you risk your brakes catching and being ripped off the calipers, or ruptoring your brake lines and loosing all your brakes.

With your old brakes, if you didnt feel your pedal bounce up and down really bad when you braked, you should be fine, although it is recomended, if you cant afford it, you cant afford it. But, might not be easy to find a mechanic that will just put the pads on and not make you at least machine them... but you wont find a mechanic at all that will put pads on a rotor that is going to become a risk, so hope your rotors are good enough to work, if you dont want to replace them.

Mar 09, 2010 | 2006 Ford F-150

1 Answer

Do i need to change the brake pads and discs???


No you don't, you can have them turn the brake disk/rotor . Turning the brake disk/rotor is when you have the surface of the disk resurfaced by having a brake lath cut the high spots down. The disk are cheap enough now that most will just replace the disk/rotor the same time they replace the brake pads. You can pick up performance drilled or slotted brake disk/rotor for almost the same price as the OEM disk/rotor. Good luck and hope this helps, you can pick up the slotted brake disk/rotor at Auto Zone for a reasonable price and they will have the step by step instruction replacing the disk and if you like to just have the disk/rotor turned, they can do they there too.

Jun 07, 2009 | 2002 Volvo S40

1 Answer

Changing brakes...removal of rotor?


if you changing the brakes you don't need to get the rotors out.you need to get the brake part
out first it has only two screws in back of the brake part....take it out, and you will be available to remove the brake. and if you want you can remove the rotors too. but you dont need to remove it. just take the brakes out and put the new ones.

May 02, 2009 | 2006 Hyundai Sonata

2 Answers

Problem changing rear rotors on 95 Toyota Avalon


Just remove the rear rotors, bull the straight off, after removing the caliper bracket. It would be a good idea to spray the small brake shoes with brake cleaner. No need to remove anything other than the rotor.

Mar 05, 2009 | 1995 Toyota Avalon

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

25 people viewed this question

Ask a Question

Usually answered in minutes!

Top Pontiac Experts

Marvin
Marvin

Level 3 Expert

81342 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8841 Answers

Are you a Pontiac Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...