Question about 1995 Toyota Camry

1 Answer

How do you know set the couiter balanceto the crank? TKS.

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Toyota Master
  • 14,036 Answers

THE CRANKSHAFT VIBRATION DAMPER CRANKSHAFT THROWS AND FLYWHEEL ALL BALANCE THE CRANKSHAFT.IF CRANKSHAFT OUT OF BALANCE AND VIBRATION GOOD AND THE CRANKSHAFT THRUST BEARING NOT WORN.CRANKSHAFT COULD BE BEND.

Posted on Mar 21, 2011

  • Jonah Oneal Mar 21, 2011

    I LEFT OUT DAMPER AFTER VIBRATION SUPPOSE TO BE VIBRATION DAMPER.

×

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do put my 1991 Chevy C1500 truck with 4.3 back n time on motor and distribitor


PULL THE SPARKPLUG OUT OF THE #1 CYLINDER ROTATE ENGINE OVER TO FIND TOP DEAD CENTER ON COMPRESSION STROKE REMOVE DIST. CAP AND SEE WHERE THE ROTOR IS POINTING AND ADJUST SO THE
#1 WIRE IS LINED UP WITH IT

Nov 20, 2012 | Cars & Trucks

1 Answer

My !978 chevy pickup has new distributor and carburator. I can hear it firng but it won't start


gyver here , twenty year wrencher.. sounds like either you got the timing out on the distributor , or the timing on the crank and cam are off. if you know the timing marks were set cam at twelve crank at six the dist is out. common for guys to set cam and crank n marks one above the other but then you must rotate engine 360 degree before you set dist back into hole. pull dist up rotate 180 degree .let me know

Feb 01, 2012 | 1978 Chevrolet C1500

1 Answer

Engine stalls driving down the road or on take off. Had code 42. electronic spark tining. E S T circiut fault. Cleared codes and installed a fuel pressure gauge. On test drive the motor, (3.1 EFI) still...


Trouble Code 42 indicates that there may be a malfunction in the Electronic Spark Timing (EST) system. During cranking, the timing is controlled by the ignition module and the ECM grounds the EST line. It expects to see no activity on this line at this time. When the ECM enters EST mode, it applies +5 volts to the BYPASS line and expects to see voltage variations on the EST line.
Reasons for the ECM to set Code 42:
1. System in BYPASS mode (i.e. EST line supposedly grounded) but activity sensed on EST line
2. System in EST mode (i.e. BYPASS line driven with +5 volts) but no activity seen on the EST line

Possible causes include:
1. BYPASS line is open or grounded
2. EST line is open or grounded
3. Poor connections between ignition module and ECM
4. Poor routing of EST harness and/or poor quality ignition wires (EMI induced electrical noise
5. Faulty or incorrect ignition module
6. Faulty ECM
7. Faulty Pick Up Coil
8. Faulty Ignition Control Module
9. Faulty Crank Sensor or the Crank Sensor magnet probe could be cracked

Jan 15, 2011 | 1991 Chevrolet Lumina

1 Answer

Automatic front windows driver and passenger do not work. back windows work


I have same issue & can't believe both motors could be bad. If ya get an answer pls let me know. dabrione@yahoo.com, tks.

Aug 29, 2010 | 1994 Buick Century

1 Answer

Dont know how to set timing on my 89 ford ranger,


first you need a timing lite second when you start it you hold the timing lite at the crank there are degree marks near the crank you should clean the crank and there is a mark on it remark it with white chaulk thats how you set timing

Aug 20, 2010 | 1989 Ford Ranger

1 Answer

I have a 94 olds 88 it has a chip in the key. i tried to jump out the starter relay now it will crank but will not start i think it has some thing to do with the pass-key decoder module but i can't find...


The dealership can bypass the security chip no problem. The chip is a resistor and they use a resistor of the same value at the bottom of the steering column to bypass. resistors and soldering are required.

Sep 22, 2009 | 1994 Oldsmobile Eighty Eight

1 Answer

Oil Level


With the car running and in park, remove the transmission dipstick.
It should be at the full mark.

Sep 30, 2008 | 1994 Jeep Cherokee Country

Not finding what you are looking for?
1995 Toyota Camry Logo

Related Topics:

141 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

75807 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22133 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8172 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...