Question about 1997 Buick Park Avenue

1 Answer

How do you remove a thermostat from a buick park avenue

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 360 Answers

  1. Drain the cooling system.
  2. Remove the engine cover.
  3. Disconnect the Inlet hose from the housing.
  4. Remove the thermostat housing bolts (A), thermostat housing (B), and the Thermostat (D).
  5. Clean the gasket mating surfaces and the housing and intake port.
To Install:
  1. Install the Thermostat (D).
  2. Install the thermostat housing (B) with a new gasket (C) and torque the bolts (A) to 15 ft-lb (20 Nm).
  3. Connect the inlet hose.
  4. Install the engine cover.
  5. Refill the cooling system.


How do you remove a thermostat from a buick park - tecnovative_167.gif

To Drain:
NOTE: Draining the cooling system with the pressure cap installed will siphon the coolant from the overflow tank.
  1. Raise and support the vehicle.
  2. Open the radiator drain **** and drain the coolant into a drain pan.
  3. Empty and wash out the coolant reservoir with soap and water.
  4. Inspect the coolant if discolored flush the system before refilling.
To Fill:
CAUTION
Follow the procedure below to insure the coolant is at the proper level. A coolant level that is too high or too low could cause engine damage.
  1. Close the radiator drain **** and lower the vehicle.
  2. Slowly fill the cooling system with a 50/50 mixture of DEX-COOL antifreeze and clean drinkable water.
  3. Install the coolant pressure cap and start the engine.
  4. Run the engine at 2,000-2,500 RPM until the engine reaches normal operating temperature than let the engine idle for 3 minutes.
  5. Turn the engine off and let the engine cool off.
  6. Top off the coolant and check the concentration of the coolant using the (J 26568) coolant and battery tester.

Posted on Mar 21, 2011

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do I replace a thermostat in a 2000 buick park ave


drain radiator remove hose remove two bolt on thermostat houseing clean place new thermostat in copper side with spring down in hole revers steps

Jan 17, 2013 | 2000 Buick Park Avenue

1 Answer

My temp gets hot but my car doesnt seem to be overheating what could it be its a 2000 buick park avenue


Here's a link to the coolant temp. switch,could be bad,its near the thermostat cover.Here's how to remove.

Dec 04, 2012 | 2000 Buick Park Avenue

1 Answer

How to change the thermostat on 2000 buick park ave ultra


The thermostat is located under the cover that the upper radiator hose connects to on the engine, let engine cool and remove plastic cover over engine and then remove the 2 bolts that hold the thermostat cover down, replace the thermostat exactly as the old one came out, refill the system with the bleeder valve open on the top of the cover over the thermostat until coolant comes out as you fill, this bleeds our out.

Nov 05, 2012 | 2000 Buick Park Avenue

1 Answer

Where is the thermostat housing on a 2000 park avenue?


Follow the upper radiator hose back to the engine. Where the hose connects to should be the thermostat housing.

Feb 12, 2012 | 2000 Buick Park Avenue

1 Answer

Where is the thermostat ocated on the 1993 buick park avenue


Follow the large radiator hose from rad to motor,where this hose connects to motor is the thermostat houseing with 2 bolts holding it on motor

Mar 13, 2011 | 1993 Buick Park Avenue

1 Answer

Engine coolant tempture gage on 1999 buick park avenue is not working


your coolant temp sensor may be bad. it should be located in the thermostat hsng.

Dec 12, 2009 | 1999 Buick Park Avenue

2 Answers

92 buick park avenue won't blow hot air - temp control seems to be working


Make sure there are no leaks and that the system is full to capacity. After the vehicle has warmed up check radiator hoses for temperature differecial also check heater core hoses. A significant difference in temperature may indicate a plugged heater core or thermostat failure

Oct 22, 2009 | 1992 Buick Park Avenue

1 Answer

96 park avenue radio removal/installation


http://www.ehow.com/how_5437765_install-radio-buick-park-avenue.html

wiring diagram

http://www.modifiedlife.com/1999-buick-park-avenue-car-stereo-wiring-diagram/



Jul 17, 2009 | 1999 Buick Park Avenue

1 Answer

1991 buick park avenue cooling fan runs all the time,what's the problem?


the thermostatic sensor in the neck of the radiator hose at the top of the engine is bad...pay someone to fix it...you'll be glad u did ($60-80)

Jun 14, 2009 | 1991 Buick Park Avenue

Not finding what you are looking for?
1997 Buick Park Avenue Logo

364 people viewed this question

Ask a Question

Usually answered in minutes!

Top Buick Experts

yadayada
yadayada

Level 3 Expert

75797 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8152 Answers

Are you a Buick Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...