Question about 2005 Hyundai Elantra

1 Answer

Hit a ditch and pulled my drivers bumper completely off on the drivers side....a black box with a hose came out and the drivers tire ran it over........what could that box be?

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Governor:

    An expert whose answer got voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 161 Answers

Evap canister likely.

Posted on Mar 21, 2011

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Location of canister vent valve solenoid on 2009 f150


For a 5.4L V8 Flex...canister Purge Valve--centered right behind the throttle body. Should see a hose with a quick disconnect and an electrical connector on one side (driver's). Opposite (passenger) side has another 6-8 inch hose that runs from the valve to the engine with a quick disconnect on the engine side. The valve itselve is about 2-3" long, black cylinder (google Motorcraft CX2447 for picture)! Very easy to replace yourself (5 min job). Remove the electrical connector (push in on rear side and pull), remove the two quick connects by squeezing the gray prongs and pushing the connector outward. Hose should slide right off. Pull valve off of bracket (there is a rubber piece that holds it on--it will slide off of the metal bracket, but have to wiggle it loose), replace part, reconnect hoses/elect and you're done. Just make sure the hoses are fully seated.

The actual canister is a black box on the inside of the frame beneath the driver side (have to get under the truck pretty far to see it). It has about 3 hoses running to it from the fuel tank. On side facing the front of the vehicle, you'll see a hose that runs up through the firewall to the purge valve.
it's mounted above where your spare tire is on some of the other motors its above your spare tire

Mar 24, 2017 | Cars & Trucks

1 Answer

What is bent when your front tire tows in at the top of the rim


the upper control arm is bent
the strut mount at the inner guard is bent
the strut is bent
best to replace all of the drivers side suspension

Oct 06, 2015 | Cars & Trucks

1 Answer

Small black box hanging behind the rear drivers tire


Charcoal canister for your evaporative emissions system.

Mar 25, 2015 | 2005 Nissan X-Trail 2.0

2 Answers

How to replace a battery on Sebring 2010?


See my pic below. The battery is in the wheel well in front of the driver side tire. I took this pic when I had the entire front bumper off to work on the radiator. You obviously don't have to take the bumper off to get to the battery, but it's still a pain. To change the battery you need to remove the driver side front tire. Then remove the plastic push pins holding the front of the black plastic wheel well. (These push pins have a center button that need to be lifted. They sell a tool, but a flat screwdriver works fine. Once the center button is lifted the push pin comes right out). Once you have the front wheel well off you can see and reach the battery. Good luck to all!
replace-battery-sebring-2010-ctwhbipqr4140ccykbyimcgi-3-0.jpg

Feb 04, 2015 | 2010 Chrysler Sebring

1 Answer

2002 ford ranger gas issues


Okay I got tired of this and did something about it . so here is the solution . Pull off the bed . 6 bolts , hit them with a 2 pound sledge hammer and use a impact or a big 1/2 drive . Disconnect tail light harness on drivers side just above bumper area. undo screws on gas tank filler . two people can lift off bed . on top of the spare tire you will see the charcoal canister . About a foot long and black with a solenoid on the drivers side .connected to this solenoid by a cigar sized hose is a black box with another hose on the other side . This is a air filter . Lets in air when the solenoid opens so the fumes can travel back up the line . Notice that the open end hose is just right for collecting all the dirt and water that flies up there . This canister as it is marked has some foam inside like a lawn mower air filter . either go buy another at the dealer or simply tap it on the truck frame and get all the dirt out and blow out with air hose would be good if it is wet inside . Blow in it to make sure air flows freely through it . Put it back on .

Okay if that just happens to not be it here is how you find out what is it . After removing the bed make sure the vents on top of the gas tank are not plugged by blowing and sucking on them . Then unhook the fume line from the solenoid on the charcoal canister . Drive , I know no lights for breaks , to gas station and start filling up . If it splashes out then it is on the tank side . If not then plug up the line you removed and fill. If it splashes out then it is after the solenoid . Put thumb over other end of solenoid where the air filter is attached after removing the filter hose of course . If it splashes out then it is the air filter .
Make sure you point that hose on the end of the air filter at a downward angle so it does not collect water and dirt again . Stupid Ford makers .

Process of elimination.

I am so glad I can now fill my tank . Why in the he## can not all these mechanics on all these forums come up with the answer ? Or even the dealership.

Aug 04, 2012 | Ford Ranger Cars & Trucks

1 Answer

1995 Mercury Villager that was in an accident - bumper sticks out


I would go to a pick N pull salavge yard and buy an entire used bumper assembly.

http://groups.yahoo.com/group/villagerquest/

Mar 29, 2010 | 1995 Mercury Villager

1 Answer

Replace Driver side headlight


Remove bolt holding driver's side front bumper and push-in clips holding bumper to tire well. Pull bumper forward to gain access to remove old and install new assembly.

Jul 15, 2008 | Mitsubishi Galant Cars & Trucks

3 Answers

Renault espace


The bumper is held on by just two 13mm bolts, the problem is getting to them. First remove the air filter and you will then see a black junction box on the right hand side, remove this and the bracket underneath to get to the bumper bolt. The driver side bolt is behind the small black junction box under a larger black junction box. Remove the small one 2/3 small bolts) to access the other bumper bolt. Its easy to do just takes a bit of time.
Mark

Jun 13, 2008 | 2000 Renault 181

Not finding what you are looking for?
2005 Hyundai Elantra Logo

Related Topics:

40 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hyundai Experts

yadayada
yadayada

Level 3 Expert

75744 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8123 Answers

Are you a Hyundai Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...