Question about Saab 9 3

Open Question

Have a p1951 and p1960 error message. i was told it probably is the throttle body. replaced and same errors pop up. reset error codes numerous times saab 9-3se conv. 115,000 miles

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 25 Answers

SOURCE: stalling no idle

Hi,if you want to now where is a leak ,start the car if is possible and spry the hosing pipes wen suddenly rpm increase you now where is the problem or ken be the trottle body!

Posted on Jan 16, 2009

  • 45 Answers

SOURCE: I have a 2001 saab 9-3se convertible and the top

Is there fluid leaking out? look at the top rams on sides. You can manually lift your top through the sequence after it unlatches. Fold 5th bow up and raise tonneau and look at rams. Any leak is bad. I could also be low on fluid wich you check at the front edge of trunk, 2 holes 1 for flashlight 1 to ck level. Requires special fluid from saab, do not substitute!

Posted on Sep 23, 2009

  • 1596 Answers

SOURCE: I am wanting to know

LIMP MODE ? I am CONFUSED With this Term. I Have Researched this On AllData and Found NO Such Term Used in My Resources and Have Not (in 30 yrs ) Heard this Term used If you Could Elaborate a Little More and Also Give the Model & Eng Size this Would Help Us Also.
there is Engine sizes>> 2.0 L, 2.3L ,2.5L .& 3.0L along with the Different Models. I / We Need A Little More DETAIL in your Explination of SYMPTOM you are Having with your Vehicle. I / We Woule Like to Help in a Fast and Eficient Manner with your Help We CAN Do This THANK YOU.
,Also Sorry to Take up too much Time Here

Posted on Nov 09, 2009

johnjohn2
  • 5763 Answers

SOURCE: I have a 2000 saab 9-3SE. When the motor heats up

check the speed sensor and also the abs wheel speed sensors. most likely its going to be speed sensor in trany,good luck

Posted on Nov 28, 2009

Testimonial: "At least we have a direction in which to go!!! Thanks!"

  • 3640 Answers

SOURCE: saab 9-5 need to give alittle throttle for cold engine start

the idle air control valve may be bad or just needs cleaned out. idle air control valve acts the same as a choke. if it is messing up it will cause engine not to run right.

Posted on Jan 27, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Alfa 1452liter twinspark, 1999 model. We clean the trottle body put it back and key code and injector light stays on and wont start


At some point the computer has detected a fault (probably the missing throttle body while you had it off) and has thrown an error code. Suggest you get the error code reset - that will probably fix it. You will need the reset device to do this or get a dealer to do it.

Mar 23, 2015 | Alfa Cars & Trucks

1 Answer

Throttle body codes


it is the thing that lets petrol into the inlet manifold then it goes into the combustion chamber, basically. These have an amount of sensors on them. one of them may have been knocked or loosened itself

Apr 09, 2014 | 1992 Cadillac DeVille

1 Answer

1996 dodge stratus with error codes 12 43 23


probably by the fresh air hose the one that hooks to the throttle body.

Apr 19, 2013 | 1996 Dodge Stratus

1 Answer

How to reset error code on 2008 accord v6


Soft reset disconneting the negative battery cable few minutes; if the code come back again, its possible that you have some problem with the sensor, wires or harnesses connections.

Keep in mind that sometimes will need OBD scanner tool to reset or delete all stored codes.

Hope this helps; also keep in mind that your feedback is important and I`ll appreciate your time and consideration if you leave some testimonial comment about this answer.

Thank you for using FixYa, have a nice day.

Sep 04, 2012 | Honda Accord Cars & Trucks

1 Answer

Reset error code on 2008 accord v6


Soft reset disconneting the negative battery cable few minutes; if the code come back again, its possible that you have some problem with the sensor, wires or harnesses connections.

Keep in mind that sometimes will need OBD scanner tool to reset or delete all stored codes.

Hope this helps; also keep in mind that your feedback is important and I`ll appreciate your time and consideration if you leave some testimonial comment about this answer.

Thank you for using FixYa, have a nice day.

Sep 04, 2012 | 2008 Honda Accord

1 Answer

Throtle sensor


It is an integrated model.The TPS is part of the motorized throttle body. If you have TPS error code. Clean the throttle body and reset it with a good scanner. If that does not work, you may have to replace it.

Jun 02, 2012 | 2004 Proton Gen-2

1 Answer

CHEVY AVEO 2006 ERROR CODE P2135.


should not have to pay for same part twice.take vechicle back to dealership tell them car not fixed you have same problem.let them know you payed them to fix car.same problem still exist.code p2135 problem could be the tps sensor or signal circuit to sensor wires and connector have a short or problem could be throttle body assembly damaged.

Feb 26, 2012 | 2006 Chevrolet Aveo LT

1 Answer

I have a 2004 Chevy Malibu LS. When driving all of a sudden loss of power no gas pedal, TC wrench, engine light will lite. I can take out of gear then put back in gear TC and wrench lite will go off and I...


Throttle body ! Take it to a Mech. that knows the electronic throttle control .
Drive by Wire Function and diagnostics by Wells Saturn is also a GM vehicle an the electronic throttle control is the same . Has the gas pedal Assembly also wiring , engine computer the DC electric motor on the throttle body . Testing like this guy does is the way to a proper fix , not guessing .

May 15, 2017 | 2004 Chevrolet Malibu

2 Answers

P1193 error code car wants to stall when stopping and accelerating


P1193 = Detected engine speed below 470 RPM. There are several possible causes/components which can contribute to this drivability issue. ELECTRONIC THROTTLE SYSTEM (ETS). In most cases, an ETS related DTC will set in pairs of codes. The first code denotes the related system or component. The second code is for the specific fault detected.
There was also probably P1191 - limp home

For this issue, on frequent occations I've found the throttle position sensor (TPS) (potentiometer) had bad spots in it and subsequently sending erratice signals to the ETS Control Module (additionally, the throttle body and plate had carbon buildup inteferring with the intake air flow. Also check for air leaks (intake air hoses, vacuum lines & tubes for cracks/leaking). Clean the throttle body & plate. Bench test the TPS. You also have an APS (Accelerator Position Sensor) located on the RH side engine compartment near the firwall next to the strut tower. These are the initial components to check/examine. Replace as needed.


ghost45_37.jpg

ghost45_38.jpg

Aug 31, 2011 | 2001 Hyundai XG300

1 Answer

What do computer codes P0068 & P0496 mean ?


P0068 MAP/MAF is Throttle Position Correlation.In this error code:--- From the error code P0068 you have its indicating a bad throttle body or throttle actuator controller.. The 2 tps sensors inside read each other and if they differ for a few seconds or milliseconds then you get a this error code with reduced power. In some cases the new connector and wiring to the throttle actuator is required and in some cases getting the throttle body cleaned helps.---------------
And code P0496 - "Evaporative Emission System High Purge Flow".------------In this error the purge valve needs to be replaced. The purge valve is mounted on the inlet manifold under the hood.Its on the top of the intake manifold, passenger side. Two hoses (one on each side) and a wire harness on the front of it. It has a red w/blue stripe and brown w/white stripe wire harness connected to it.Remove and replace this valve.-----------------This will help.Thanks.Helpmech.

Jan 20, 2011 | 2008 Saturn Astra

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

219 people viewed this question

Ask a Question

Usually answered in minutes!

Top Saab Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

yadayada
yadayada

Level 3 Expert

75797 Answers

rgbypoet

Level 2 Expert

166 Answers

Are you a Saab Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...