Question about Isuzu Rodeo

Open Question

How to replace the rear wheel bearings on a ra rodeo 2 wheel drive

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Mr BrokRench
  • 1623 Answers

SOURCE: I need instructions on how to replace rear wheel bearings on my 1994 Honda Civic

Bearings are pressed into the hubs...much easier, faster and economical (if you don't have a press) to replace the complete bearing/hub assembly, no pressing is needed, since bearings are already pressed into the new hubs. Cost..aprox, 60 buxs each.
Here are the steps for the rear replacement...
Loosen the lug nuts on a rear wheel. 2) Chock the wheels and jack the rear of the car on the side with the lug nuts that you just loosened. 3) Remove the wheel by removing the lug nuts. 4) Pry open the dust cap covering the center of the axle/spindle. A small screwdriver tapped into the space between the hub and dust cap will work well for this. 5) With the dust cap now removed, use a thin center punch to straighten the little dent in the rim of the spindle nut so that you will be able to turn it freely in the next step. 6) Use a 32mm socket and a large breaker-bar to loosen the spindle nut. Unscrew the nut all the way and place it in a clean, safe area. 7) You should now be able to slide the hub/bearing assembly from the shaft. 8) Installation is the reverse of removal. Use plenty of high-temperature wheel bearing grease on all surfaces before you mount the replacement hub assembly.

IMPORTANT: Torque the spindle nut to 134 ft/lbs....(per manual specs)

When reinstalling the dust caps, tap them gently into place to avoid denting them...Install wheels, jack her down and pat yourself on the back...job complete.
Good luck..hope this will fixya up...please take time to leave me a fixya rateing...

Posted on May 23, 2009

  • 1 Answer

SOURCE: Rear Wheel Bearing Repair; 2005 pontiac aztek

Remove the brake caliper
Remove the disc, (rotor)
Remove the 34mm nut on the axel shaft
Remove the three (3) bolts from the back side
You will need a wheel puller (three jaw will work well)
Place the puller over the hub and tighten, this will push the shaft out of the hub. Now you have to pull the hub assy. out of the mounting bracket. I found hitting each side,of the hub with a lead hammer to work well. Don't forget to disconnect the ABS senser on the back side of the hub assy.
Do not over tighten the 34mm axel nut when you install the new assy. If you use an impact whrench on it you will damage the bearing.

Posted on May 03, 2009

  • 119 Answers

SOURCE: Procedure for replacing rear wheel bearings 2000 Forester

i'm assuming you don't have a hubshark,this is a tool that will alllow you to remove the bearing while the knuckle is attached to the car,you may be able to rent this tool at a auto prts store .if not you need to remove the entie knuckle,first remove the trailing arm bolt,then the lateral link bolt{long and stubborn bolt},disassemble the brake shoes and parking brake cable,abs sensor if equipped the knuckle to strut bolt{no marking necessary they are not eccentric} then you need a to use or borrow a press to remove hub and bearings good luck

Posted on Jul 26, 2009

  • 101 Answers

SOURCE: how do i replace the rear wheel bearing on my peugeot 206

wheel off remove the tin cap in the centure of the hub undo the big nut put the wheel back on with just 2 bolts finger tight so you can pull the hub off.once the hub is off take the 2 wheel bolts back out.now look in side the hub were the big nut was and you will see a sir clip take that out.then use a socket and a bench vice to press the old bearing out.use the socket and bench vice to put the new bearing back in.

Posted on Aug 01, 2009

alicantecoli
  • 22114 Answers

SOURCE: How do I change right rear wheel bearing on my

is it front or rear wheel drive¿¿

Posted on Oct 30, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Spark plug firing order


Hello Harvey, My information shows firing order of 123456. #1 being passenger's front cylinder and #2 being driver's front cylinder.

Jul 30, 2014 | 1995 Isuzu Rodeo

1 Answer

I have a 2005 ra crew cab 3.5L v6, it feels like the brakes are on when I select 4h. What is the cause?


Most Likely different tyre wear, or sizes, between front and rear wheels. The rodeo locks the front and rear together there is no differential between front and rear.
fuel use, wear and tear, and control are all compromised, if this is the case.

Jul 06, 2014 | 2005 Holden Rodeo

1 Answer

I have 2003 RA Holden Rodeo 3.0 ltr T/Diesel. The 2 front wheels don't seem to be engaging when i put it into 4wd (high or low range). I can hear the high and low range click in when i press the buttons...


Does yours have AUTO hubs, there are some luxory models have auto hubs, these rely on difference in drive on the axles,(wheel spin) others have manual locking hubs, these actually need to be engaged manually, these require you to twist the centre of the hub to engage and disengage the front hubs, these sometimes require you to reverse to disengage properly, Rodeo had both depending on model. Happy New Year

Dec 30, 2013 | Isuzu Rodeo Cars & Trucks

1 Answer

I need a step by step instructions how to replace rear wheel bearings on a ISUZU-HOLDEN RODEO 92 4 wheel drive.


Go to autozone.com register, then add your vehicle and look up the repair manuals. they are very good step by step instructions.

Jan 26, 2011 | Isuzu Rodeo Cars & Trucks

1 Answer

Is a 2002 isuzu rodeo front wheel drive ? And do you have to remove the axle to replace a transmission


There are no front wheel drive rodeos but there are 4 wheel drive and all wheel drive. If it is not 4 or all wheel drive then there is no front shafts. You will need to remove the rear drive shaft though to remove the transmission. Hope this helps. Good luck.

Aug 27, 2009 | 2002 Isuzu Rodeo

1 Answer

We are trying to replace my rear wheel bearing. Can anyone give any ideas how to get it apart?


here is how to replace it on a 2 wheel drive please do not forget to rate and comment about your experience today. 2-Wheel Drive
  1. Before servicing the vehicle, refer to the Precautions Section.
  2. Remove or disconnect the following:
    • Negative battery cable
    • Rear wheel
    • Rear brake drum
    • Wheel hub nut
    • Wheel hub
    • Inner wheel bearing race from the hub
    • Snapring
    • Wheel bearing outer race from the knuckle

06017-esca-g92.gif
06017-esca-g93.gif
06017-esca-g94.gif
06017-esca-g95.gif 06017-esca-g96.gif

To install:
  1. Install or connect the following:
    • Wheel bearing in to the knuckle
    • Snapring
    • Wheel hub into the wheel bearing
    • Wheel hub nut. Torque the nut to 214 ft. lbs. (290 Nm).
    • Brake drum
    • Rear wheel
    • Negative battery cable
06017-esca-g97.gif
06017-esca-g98.gif

Apr 11, 2009 | 2005 Ford Escape

1 Answer

Clutch kit for a 99 rodeo 5 speed 3.2 v-6


replace the complete clutch assembly which includes the disk, pressure plate and the release bearings, some of them also have a polot bearing / bushing, replace it while you are at it make sure that the fly wheel is nto overheated or scored if it is replace the fly wheel or atleast machine the fly wheel in a machine shop, and replace the rear main engine oil seal. when every thing is out and dont forget to rate me please

Dec 04, 2008 | 1999 Isuzu Rodeo

1 Answer

Rear Axle Bearing Replacement


That absolutely sounds like an axle (wheel) bearing. Jack up that corner of the truck and grab the top and bottom of the wheel, and shake like crazy. If you have any play whatsoever, it's a sign of a bad bearing (although you could have a bad one and not have any play - it would only mean the bearing isn't worn badly enough to cause looseness in the wheel).

You should be able to remove the axles without opening the diff up. If the axles have c-clips or snap rings on the ends inside the diff, you can usually get the axles out by dismounting them from the hubs and getting them free of all attachment except the diff, and then use a large flat-tip screwdriver as a pry bar. Use it right where the axle body mates to the diff, and lever it while you pull/yank/shake/swear at the axle, and you'll manage to pop the axle out of the diff. Sometimes it takes some time and profanity, but so far it's worked for me everytime.

Jul 30, 2008 | 1992 Isuzu Rodeo

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

506 people viewed this question

Ask a Question

Usually answered in minutes!

Top Isuzu Experts

yadayada
yadayada

Level 3 Expert

75744 Answers

Steve Hurc
Steve Hurc

Level 3 Expert

450 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Are you an Isuzu Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...