Question about 1996 Toyota Camry

1 Answer

Do I have to emty the tank to change the fuel filter. and direction how

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Scholar:

    An expert who has written 20 answers of more than 400 characters.

  • Expert
  • 90 Answers

Although it is not absolutely necessary to empty the fuel tank prior to removal of the tank and then the fuel pump, it makes dropping the tank a lot easier and safer as well.

Posted on Mar 21, 2011

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Whats involved with changing fuel filter on a 2008 Pontiac wave 5 door? Do I need to change fuel pump too? If so do I need to drop tank? Where is location of he fuel filter? Thanks Justin


Hey Justin, your fuel filter is a NON-SERVICEABLE filter.. there is nothing you can do. Changing the fuel pump(it has a filter on it)
Auto Metal Direct OER Fuel Tank Sending Unit Filter Screen
https://www.rockauto.com/en/catalog/pontiac,2008,wave,1.6l+l4,1447327,fuel+&+air,fuel+pump+&+housing+assembly,10147
Remove the back seat,,there should be a "trap door" in there-in the top of the gas tank... disconnect the battery first, then remove the fuel pump..

Jun 18, 2017 | Pontiac Cars & Trucks

1 Answer

How to change fuel filter on the 2006 scion xa


Open the hood and locate the fuel filter. If the fuel filter is not in the engine compartment, follow the fuel line from the tank until the fuel filter is located.

If the fuel filter has a clear case, inspect the filter element for dirt.

If the fuel filter case is not see-through, remove it from the fuel line. Drain the fuel from the filter into a container and inspect the condition of the fuel.

Install the new fuel filter making sure that the flow is in the correct direction. The arrow on the fuel filter is the direction of flow from the tank to the engine.

Launch X431

Aug 21, 2013 | 1995 Honda Accord

1 Answer

Tools needed to change fuel filter


Removal & Installation

Print

  1. Before servicing the vehicle, refer to the Precautions section.
  2. Properly relieve the fuel system pressure.
  3. Remove or disconnect the following:

    Negative battery cable and fuel filler cap, if not already done
  4. Raise and support the vehicle.

    Fuel tank shield, if equipped Quick connect fittings from the filter Filter feed nut and the clamp bolt Filter and the clamp from the vehicle

    0996b43f80209728.jpg enlarge_icon.gifenlarge_tooltip.gif

    Fig. Typical fuel filter location along frame rail


To install:
  1. Install or connect the following:
    NOTE The filter has an arrow (fuel flow direction) on the side of the case, be sure to install it correctly in the system, the with arrow facing away from the fuel tank.


    Filter and clamp with the directional arrow facing away from the fuel tank, toward the throttle body


    Tighten the fuel feed nut Tighten the filter clamp assembly bolt Fuel quick disconnect fittings to the filter Fuel tank shield, if equipped Fuel filler cap Negative battery cable
  2. Start the engine and check for leaks

Sep 04, 2012 | 2000 GMC Jimmy

1 Answer

2000 s-10 4 cyl. truck runs good gas gadge gose from full to emty with a full tank or emty tank dose not matter? whats the fix!


had the same problem on my 2000 s-10 ,turned out the wire from sending unit had worked loose(bad crimp). The fuel pump had recently been replaced. the connector to the sending unit was different from original . the new pump included the different connector ,but it had to be spliced in .Check connections at tank/fuel pump.Also there were 3 ground connections 1 tank to frame 2 bed to frame on my s-10 hope this helps

Mar 30, 2011 | 2000 Chevrolet S-10

1 Answer

I Have a 1999 f350 Super duty Dually 7.3 Powerstroke. It starts hard in 80 to 90 Deg. weather and runs like it is 20 below. Then when pulling a emty or under a load has no power like id is running on 4...


It could be that you have picked up a batch of dirty fuel that has clogged the gauze input filter that is part ot the fuel pump inside the fuel tank.

Jul 29, 2010 | 1999 Ford F350 Regular Cab

1 Answer

Changed the fuel pump and fuel filter but now car


It could be that the fuel filter was put on backwards or it could be the wrong filter. Some fuel filters will only allow the Fuel to flow a certain direction properly. There should be an arrow pointing the direction of flow on the filter or in and out are stamped on the end of the filters. If you can I would crawl underneath your car and locate the fuel filter. Look for the fuel line that comes from the fuel tank and follow it to the Fuel filter. Look for the arrow or the in and out. The back of the arrow should be where the line comes into it from the fuel tank and the head of the arrow should be connected to the line going towards the front of the car. If in and out are stamped on the filter, the line connected to the IN side of the filter should be the line coming from the fuel tank and the Out side should be the Line going towards the engine.. Hope this helps a bit

Apr 13, 2010 | 1999 Chevrolet Malibu

2 Answers

Gas gage read full when empty and sometimes emty


You have a bad fuel level sensor.The fuel tank needs to come out and the sensor replaced.You don`t have to replace the pump assembly.You can get the level sensor separate.I`m not sure if the parts stores have it but I know the dealerships do.Hope this helps.Good luck.

Mar 16, 2010 | 2004 Pontiac Montana

1 Answer

How do i change the fuel filter when it is


The fuel filter located in the tank is good for the life of the pump and does not need replacing. The filter usually changed is under the car - follow the fuel lines till you find the small barrel type container with a fitting on each end. (Note the direction of flow indicated by the arrow on the filter.)

Jan 19, 2010 | 1996 Chrysler Sebring

1 Answer

In drive mostly and idle it sputters and as no power i have a new fuel filter not on yet but engine light finally came on after i got gas today was on emty


Check your engine oil and please put the new fuel filter on. Do not let your tank get empty if possible because you will get sediment from the bottom of your tank and clog up you fuel filter and cause the car to sputter or cut off. Make sure your gas cap is on tight after putting gas in you car. The leading cause of the check engine light is a loose gas cap according to car shops. Good Luck

Oct 09, 2009 | 2003 Ford Focus

1 Answer

Tank is full but guage says emty


THIS PROBLEM IS CAUSED BY A DEFECTIVE GAS GUAGE SENDING UNIT, U WILL NEED TO PULL THE FUEL TANK AND REPLACE IT.

Feb 11, 2009 | 2004 Chevrolet TrailBlazer

Not finding what you are looking for?
1996 Toyota Camry Logo

93 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

76848 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8589 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...