Question about 1996 Plymouth Grand Voyager

1 Answer

1996 grand voyager need to know how to replace front lower control arm bushings, tools needed ect...

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    MVP:

    An expert that gotĀ 5 achievements.

    Champion:

    An expert who has answered 200 questions.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

  • Contributor
  • 299 Answers

Cheaper to buy a new one that already has new ball joint and bushing installed, just swap out old one.no fuss no rental tools , etc.. cheap around 120.00 shop around. u will pay that for ball joint and bushings.

Posted on Mar 20, 2011

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where are the bushings for the low control arm on 1996 chevy tahoe 4wd located


If you are replaceing both sides (drivers & passangers (recomended)) you will need 4 bushes in total 2 front susp rear & 2 front susp front. There is 2 bushes both sides (front of front & rear of front) The lower control arms go from the chassis to the lower ball joints (just behind tyres at bottom) will be a big job!

Jun 04, 2012 | Cars & Trucks

1 Answer

How do i change my rubber bushings on the front suspention of my 1997 dodge ram 1500


opper Control Arm Bushings
  • To access the upper control arm, remove the shock absorber and the strut bar. Also, disconnect the sway bar from the lower control arm, if your particular Ram model is equipped with it. After that, you can hold the coil spring in place with a spring compressor.
    Secure the wheel hub assembly to the chassis using a wire before you disconnect the upper ball joint. This will prevent damage to the brake hose. When ready, release the ball joint using a ball-stud loosening tool (see Resources).
    The upper control arm mounts to the chassis with a cam bolt assembly. Once removed, you can place the control arm on a vise and remove the bushings using a bushing service tool (see Resources). When installing the new bushings, do not use any lubricant but make sure the flange on the bushing end seats properly on the arm bore. Then re-install the upper control arm. When finished, take your Dodge vehicle to a good shop to align the front suspension.
Lower Control Arm Bushings
  • Remove the shock absorber and strut bar. If your particular model is equipped with a sway bar, disconnect it from the lower control arm.
    Secure the coil spring with a spring compressor and release the lower ball joint from the wheel/hub assembly using a ball stud loosening tool (see Resources).
    Now you can release the lower control arm by removing the rear mounting bolts. Remove the bushings with a bushing service tool (see Resources). When installing the new bushings, do not use lubricant and make sure they seat properly on the control arm bore. Then replace the lower control arm. When finished, take your Dodge vehicle to a good shop to align the front suspension

Oct 20, 2011 | Cars & Trucks

1 Answer

Excessive play in the steering wheel, car is all over the road. What could this be?


The steering gear box is worn out. And, there's probably worn front suspension components adding to the problem. You will need to check the following parts for looseness or movement: Idler Arm, Upper and Lower Ball Joints, Control Arm Bushings, Pitman Arm, Inner and Outer Tie Rod Ends, Front Hub Bearings. All of these can be replaced in your driveway with the exception of the Control Arm Bushings which are pressed in and require special tools to remove and install the bushings. If you can't replace all of them, concentrate your efforts on the following: Steering Box, Idler arm, and Control Arm Bushings. If you can afford to have all of them done, the front suspension would be factory fresh and should, with proper wheel alignment, drive like a new car.

Dec 24, 2010 | 1996 Isuzu Trooper

1 Answer

How to chnge control arm bushing on 1994 dodge intrepid


Here are the instruction on how to replace your control arm bushing. please not that there is a special tool needed that you will need to get from you auto parts retailer. you can usually rent these tools.
    1. Turn the control arm over in the arbor press, then position the arm so that it is supported by the receiver tool MB-990799 as shown.
  1. Position the new bushing into the control arm so it is square with the bushing hole. Position the installer tool MB-6644-1 or equivalent on top of the bushing, with the bushing setting in the recessed area of the installer tool. Press the bushing into the control arm.
  2. Press the control arm bushing into the control arm until the installer tool squarely bottoms against the surface of the control arm. When the installer tool squarely bottoms on the control arm, the bushing is installed in the arm in the correct position.
  3. Install the tension strut into the strut bushing in the control arm. Position the tension strut in the control arm with the word FRONT stamped in the tension strut positioned away from the control arm. With an open end wrench on the flat of the tension strut to stop the tension strut from turning. Tighten the NEW tension strut-to-control arm retaining nut to 110 ft. lbs. (150 Nm).
  4. Install the lower control arm and tension strut back onto the vehicle. Refer to the Lower Control Arm procedure earlier in this section.


Control Arm-to-Tension Strut Bushing
To replace the control arm tension strut bushing, the control arm and tension strut assembly must be removed. The removal of the bushing requires the use of an arbor press.
  1. Thoroughly lubricate the replacement tension strut bushing, control arm and installer tool 6644-3 or equivalent with a silicone lubricant.
  2. By hand, install the tension strut bushing into the large end of the installer tool. Press the bushing into the installer tool as far as it will go by hand.
  3. Position the control arm in the arbor press so that the tension strut hole in the control arm is centered on the receiver tool MB-990799 or equivalent. Position the installer tool with the previously installed bushing, inside of the tension strut bushing hole in the control arm. Position the installer tool on top of the tension strut bushing. Using the arbor press, press the tension strut bushing into the control arm. As the bushing is being pressed into the arm, a pop will be heard. When the pop is heard, the installer tool will slightly move up off the control arm. At this time remove the control arm assembly from the press and pull the tool MB-6644-3 off of the tension strut bushing in the control arm.


Jun 19, 2010 | 1994 Dodge Intrepid

1 Answer

How do I replace the upper Control arms on My 1979 chevy 1/2 ton pickup. I saw a replacement control arm that has the bushings and ball joints already installed. I'm trying to save the high labor cost that...


Since the new arm comes with the bushings, there is no reason to get the tool to install them. Upper arms are relatively easy to install...just a bolt out, bolt in operation as the springs aren't involved. Support the suspension under the lower control arm to take any tension off the upper arm.

Apr 27, 2010 | 1978 Chevrolet C1500

1 Answer

Need a diagram bad....!!!


The front suspension is a combination strut and spring design. The control arms (11) pivot from the crossmember (12). On base models conventional rubber bushings are used for the lower control arm pivots. On up-level suspensions the front bushing is replaced by a cross axis bearing.

Oct 02, 2009 | 1999 Pontiac Grand Am GT

1 Answer

Need to know how to replace lower control arm


LOWER CONTROL ARM

REMOVAL
1) Raise and support vehicle. 3) Remove the steering knuckle.
Remove the bolts fastening the power steering cooler to the front suspension cradle crossmember reinforcement (Fig. 21). 5) Remove the lower control arm rear bushing retainer bolts located on each side of each lower control arm rear bushing. NOTE: The bolts fastening the cradle crossmember reinforcement are of three different thread sizes. Note the location of the various sizes.

6) Remove the bolts attaching the cradle crossmember reinforcement to the front suspension cradle crossmember (Fig. 22). Remove the 2 bolts fastening the reinforcement and rear of cradle crossmember to the body of the vehicle. Remove the reinforcement. 7) Remove the pivot bolt attaching the front bushing of the lower control arm to the front suspension cradle crossmember. 8) Remove the lower control arm.

Sep 25, 2009 | 2006 Dodge Caravan

1 Answer

How to change upper control arm on 1996 Honda Civic DX ?


UPPER CONTROL ARM:

Do not disassemble the upper arm. If the ball joint or bushings are faulty, or the upper arm is damaged, the entire upper arm must be replaced.
  1. Raise and support the vehicle safely.
  2. Remove the front wheels. Support the lower control arm assembly with a floor jack.
  3. Separate the upper ball joint from the steering knuckle using a ball joint separator tool.
  4. Remove the self-locking nuts from the upper arm anchor bolts. Remove the upper arm from the vehicle.

Do not disassemble the upper arm. If the ball joint or bushings are faulty, or the upper arm is damaged, the entire upper arm must be replaced.
To install:
Use new self-locking nuts when installing the upper arm and strut.
  1. Install the upper control arm assembly into the strut tower.
  2. Connect the upper ball joint.
  3. Install the front wheels and lower the vehicle.
  4. With all four of the vehicle's wheels on the ground, torque the upper control arm nuts to 47 ft. lbs. (65 Nm). Torque the castle nut to 32 ft. lbs. (44 Nm); then, only tighten it enough to install a new cotter pin.
  5. Tighten the wheel nuts to 80 ft. lbs. (110 Nm).
  6. Check and adjust the vehicle's front end alignment.
The bushings on the front lower control arms are replaceable on most models.
This procedure requires the use of a press and may be above the skill range of the average driveway enthusiast. It is recommended that this procedure be done by a qualified machine shop if you are not skilled in the proper use of a press.
  1. Remove the lower control arm that is in need of new bushings.
It is recommended that both the left and right lower control arm bushings be replaced at the same time. The vehicles handling may become unstable if there are new bushings on one side of the car and worn ones on the other.
  1. Set up the control arm in a press.
  2. Using a impact socket of the correct length and size, press out the old bushing.
  3. Install the new bushing by slowly using the press to push it into the control arm.
  4. WARNINGExcessive force could cause the bushing to bend or tear so be careful.
  5. Once the bushing is properly seated in the control arm, remove the arm from the press and install it on the vehicle.

Apr 05, 2009 | 1996 Honda Civic

2 Answers

Control arm bushings


Special tools are required. Definitely not for the novice. An alignment will be needed after the required work is performed

Apr 03, 2009 | 2000 Buick LeSabre

2 Answers

Lower Control Arm Bushing replacement


Hi,
I just did this job on my 98 regal, and I own the service manuals also. The lower control arm bushing that usually goes, is the front one. The rear one doesn't usually go, it is horizontally mounted. The front one for some reason is vertical. The control arm must be removed, and put in a vise. The front bushings outer metal sleeve, must be driven out with a chisel. It comes out easily. The new bushing can be tapped in with a hammer. Hope this helps!
JOEVETTE

Feb 10, 2009 | 1998 Buick Century

Not finding what you are looking for?
1996 Plymouth Grand Voyager Logo

176 people viewed this question

Ask a Question

Usually answered in minutes!

Top Plymouth Experts

yadayada
yadayada

Level 3 Expert

75797 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8140 Answers

Are you a Plymouth Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...