Question about Subaru DL

1 Answer

No spark, one of the negative wires from battery is hanging loose with a bracket attached

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 492 Answers

I don't know what the wire does but you should ground the bracket to the frame or engine (wherever it will fit).

Posted on Mar 21, 2011

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My mother has a 1993 Oldsmoblile Cutlass Cierra. It's a 3.3. She had a new engine put in it last year. Now her car died yesterday. She had to have it towed home so my brother could look at it. He got...


Check for spark. My guess would be the ignition module going out, but could also be the crank sensor. The module sits under the coils. Check all coils for spark. If any coil doesn't spark, you can try replacing just that coil, but the problem may still be the module underneath. If you have a meter, run a resistance check on each coil from the terminals to ground. If the same coil that doesn't fire aslo has a different resistance, replace that coil.
If you have a meter, check the AC voltage on each of the crank sensor wires shown as compared to ground or battery positive. If the AC voltages are different on the three wires, suspect the sensor is bad, but also check the tone ring on the pulley (Fig 2 below) for any damage.
Please see my tip at http://www.fixya.com/cars/r5821173-doesnt_car_start_gasoline_engines for how to check for spark. These are genericinstructions.
The 3.3L engine is the only one with the C 3 I system. REMOVAL and INSTALLATION C3I Module See Figure 1
  1. Disconnect the negative battery cable.
  2. Unplug the 14-way connector at the ignition module.

jturcotte_1656.gif
Fig. Fig. 1: Distributorless C 3 I coils and module system - 3.3L engine
  1. Tag and disconnect the spark plug wires at the coil assembly.
  2. Remove the nuts and washers securing the C 3 I module assembly to the bracket.
  3. Remove the 6 bolts attaching the coil assemblies to the ignition module.

To install:
  1. Install the coil assemblies to the ignition module and install the 6 attaching bolts.
  2. Install the nuts and washers attaching the assembly to the bracket.
  3. Connect the spark plug wires.
  4. Engage the 14-way connector to the module.
  5. Connect the negative battery cable, then reset the clock, radio and any other accessories.

Ignition Coil(s)
  1. Disconnect the negative battery cable.
  2. Tag and disconnect the spark plug wires.
  3. Remove ignition coil attaching bolts, then the ignition coil from the module.

To install:
  1. Install the coil(s) and attaching bolts.
  2. Connect the spark plug wires.
  3. Connect the negative battery cable, then reset the clock, radio and any other accessories.

Dual Crankshaft Sensor
See Figures 2, 3 and 4
  1. Disconnect battery negative cable.
  2. Remove serpentine belt from crankshaft pulley.
  3. Raise and safely support the vehicle.
  4. Remove right front tire and wheel assembly, then the inner access cover.
  5. Remove crankshaft harmonic balancer retaining bolt and crankshaft harmonic balancer.
jturcotte_1657.gif

Fig. Fig. 2: Harmonic balancer with interrupter rings on C 3 I system
  1. Unplug the electrical connector from the sensor and remove the crankshaft sensor from the vehicle.

To install:
  1. Loosely install the crankshaft sensor on the pedestal.
jturcotte_1658.gif

Fig. Fig. 3: Dual crankshaft sensor - C 3 I system
  1. Position the sensor with the pedestal attached on special tool J-37089.
  2. Position the tool on the crankshaft.
  3. Install the bolts to hold the pedestal to the block face. Tighten to 14-28 ft. lbs. (20-40 Nm).
  4. Tighten the pedestal pinch bolt to 30-35 inch lbs. (3-4 Nm).
  5. Remove special tool J-37089.
  6. Place special tool J-37089 on the harmonic balancer and turn. If any vane of the harmonic balancer touches the tool, replace the balancer assembly.

A clearance of 0.025 inch is required on either side of the interrupter ring. Be certain to obtain the correct clearance. Failure to do so will damage the sensor. A misadjusted sensor of bent interrupter ring could cause rubbing of the sensor, resulting in potential driveability problems, such as rough idle, poor performance, or a no start condition.
  1. Install the balancer on the crankshaft and install the crankshaft balancer bolt. Tighten to 200-239 ft. lbs. (270-325 Nm).
  2. Install the inner fender shield.
  3. Install the tire and wheel assembly. Tighten to 100 ft. lbs. (140 Nm).
  4. Lower the vehicle.
  5. Install the serpentine belt.
  6. Connect the negative battery cable, then reset the clock, radio and any other accessories.
jturcotte_1659.gif

Fig. Fig. 4: Distributorless C 3 I positioning tool J-37089 for installing dual crankshaft sensor.system - 3.3L engine

May 07, 2011 | 1990 Oldsmobile Cutlass Ciera

1 Answer

Where is the starter located on my 2003 nissan sentra ser


Starter Motor -located to articulate with flywheel that has gear teeth between the engine and transmission accessible from down below. REMOVAL & INSTALLATION 240SX WITH AUTOMATIC TRANSMISSION
  1. Before servicing the vehicle, refer to the precautions in the beginning of this section.
  2. Support the transmission with a jack and remove the 4 rear mounting bracket bolts.
  3. Lightly lower the transmission to make room and pull out the dipstick tube.
  4. Remove or disconnect the following:
    • Negative battery cable
    • Connector bracket from the front mount bracket
    • Harness connector
    • Starter bolts
    • Starter
    To install:
  5. Install or connect the following:
    • Starter and torque the bolts to 30-37 ft. lbs. (40-50 Nm)
    • Harness connector
    • Connector bracket to the front mount bracket
    • Dipstick tube
    • Transmission into position
    • 4 rear mounting bracket bolts
    • Negative battery cable
  6. Remove the transmission jack
WITH MANUAL TRANSMISSION
  1. Before servicing the vehicle, refer to the precautions in the beginning of this section.
  2. Remove or disconnect the following:
    • Negative battery cable
    • Connector bracket from the front mount bracket
    • Harness connector
    • Starter bolts
    • Starter
    To install:
  3. Install or connect the following:
    • Starter and torque the bolts to 30-37 ft. lbs. (40-50 Nm)
    • Harness connector
    • Connector bracket to the front mount bracket
    • Negative battery cable
1.6L and 2.0L Engines
  1. Before servicing the vehicle, refer to the precautions in the beginning of this section.
  2. Remove or disconnect the following:
    • Negative battery cable
    • Wiring at the starter
    • Bolts attaching the starter to the engine
    • Starter
    To install:
  3. Install or connect the following:
    • Starter and torque the bolts to 70 inch lbs. (8 Nm)
    • Starter electrical connections
    • Negaative battery cable
Maxima
  1. Remove or disconnect the following:
    • Negative battery cable
    • Air duct
    • Harness protector from the harness
    • Starter wiring at the starter
    • Starter-to-engine bolts
    • Starter from the vehicle

      Image 89612G12l Not Found

    To install:
  2. Install or connect the following:
    • Starter and torque the long bolt to 57-72 ft. lbs. (77-98 Nm) and the short bolt to 22-30 ft. lbs. (30-41 Nm)
    • Starter wiring
    • Harness protector
    • Air duct
    • Negative battery cable
Altima
  1. Remove or disconnect the following:
    • Negative battery cable
    • Air inlet tube
    • Harness bracket
    • Wiring at the starter
    • Starter
    To install:
  2. Install or connect the following:
    • Starter and torque the bolts to 60 inch lbs. (7 Nm)
    • Starter electrical connectors
    • Harness bracket
    • Air inlet tube
    • Negative battery cable

Nov 03, 2010 | 2003 Nissan Sentra

1 Answer

How do i change the starter on a 2000 nissan altima


I hope this helps:

REMOVAL & INSTALLATION 240SX WITH AUTOMATIC TRANSMISSION
  1. Before servicing the vehicle, refer to the precautions in the beginning of this section.
  2. Disconnect the negative battery cable.
  3. Support the transmission with a jack and remove the 4 rear mounting bracket bolts.
  4. Lightly lower the transmission to make room and pull out the dipstick tube.
  5. Remove or disconnect the following:
    • Connector bracket from the front mount bracket
    • Harness connector
    • Starter bolts
    • Starter
    To install:
  6. Install or connect the following:
    • Starter
    • Starter bolts. Tighten the bolts to 30–37 ft. lbs. (40–50 Nm).
    • Harness connector
    • Connector bracket to the front mount bracket
    • Dipstick tube
    • Transmission into position
    • 4 rear mounting bracket bolts
  7. Remove the transmission jack
    • Negative battery cable
WITH MANUAL TRANSMISSION
  1. Before servicing the vehicle, refer to the precautions in the beginning of this section.
  2. Remove or disconnect the following:
    • Negative battery cable
    • Connector bracket from the front mount bracket
    • Harness connector
    • Starter bolts
    • Starter
    To install:
  3. Install or connect the following:
    • Starter
    • Starter bolts. Tighten the bolts to 30–37 ft. lbs. (40–50 Nm).
    • Harness connector
    • Connector bracket to the front mount bracket
    • Negative battery cable
1.6L and 2.0L Engines
  1. Remove or disconnect the following:
    • Negative battery cable from the battery
    • Wiring at the starter
    • Bolts attaching the starter to the engine
    • Starter from the vehicle
    To install:
  2. Install or connect the following:
  3. Install the components in the reverse order of removal.
Maxima
  1. Remove or disconnect the following:
    • Negative battery cable from the battery
    • Air duct
    • Harness protector from the harness
    • Starter wiring at the starter
    • Starter-to-engine bolts
    • Starter from the vehicle Fig. 1: Starter location and mounting detail — Maxima with a manual transaxle 89612g12.gif
    To install:
  2. Install or connect the following:
    • Starter
    • Starter attaching bolts. Tighten the long bolt to 57–72 ft. lbs. (77–98 Nm) and the short bolt to 22–30 ft. lbs. (30–41 Nm).
    • Starter wiring
    • Harness protector
    • Air duct
    • Negative battery cable
  3. Start the engine a few times to make sure of proper operation.
Altima
  1. Remove or disconnect the following:
    • Negative battery cable from the battery
    • Air inlet tube
    • Harness bracket
    • Wiring at the starter
    • Bolts attaching the starter to the engine
    • Starter from the vehicle
    To install:
  2. Install the components in the reverse order of removal.
prev.gif next.gif

Jul 13, 2010 | 2000 Nissan Altima

1 Answer

How do you remove a 1999 Nissan Altima starter?


Nissan Car Altima & Sentra 1999-06 StarterRemoval & Installation
  1. Remove or disconnect the following:
    Negative battery cable Air duct Harness protector from the harness Starter wiring at the starter Starter-to-engine bolts Starter from the vehicle


  2. b53bb6c.jpg
    Fig. Starter location and mounting detail-3.0L Maxima with a manual transaxle


    b2eb267.jpg
    Fig. Starter location and mounting detail-3.5L Maxima

To install:
  1. Install or connect the following:
    Starter and torque the long bolt to 57-72 ft. lbs. (77-98 Nm) on Altima and Maxima and 41 ft. lbs. (55 Nm) on 350 Z. torque the short bolt to 22-30 ft. lbs. (30-41 Nm) Starter wiring Harness protector Air duct Negative battery cable
  1. Remove or disconnect the following:
    Negative battery cable Air inlet tube Harness bracket Wiring at the starter Starter

To install:
  1. Install or connect the following:
    Starter and torque the bolts to 60 inch lbs. (7 Nm) Starter electrical connectors Harness bracket Air inlet tube Negative battery cable

1.6L & 2.0L Engines
  1. Before servicing the vehicle, refer to the precautions in the beginning of this section.
  2. Remove or disconnect the following:
    Negative battery cable Wiring at the starter Bolts attaching the starter to the engine Starter
To install:
  1. Install or connect the following:
    Starter and torque the bolts to 70 inch lbs. (8 Nm) Starter electrical connections Negaative battery cable

1.6L, 1.8L & 2.0L Engines
  1. Before servicing the vehicle, refer to the Precautions section.
  2. Remove or disconnect the following:
    Negative battery cable Wiring at the starter Bolts attaching the starter to the engine Starter
To install:
  1. Install or connect the following:
    Starter and torque the bolts to 70 inch lbs. (8 Nm) Starter electrical connections Negative battery cable

1.8L & 2.0L Engines
  1. Before servicing the vehicle, refer to the Precautions section.
  2. Remove or disconnect the following:
    Negative battery cable Wiring at the starter Bolts attaching the starter to the engine Starter
To install:
  1. Install or connect the following:
    Starter and torque the bolts to 70 inch lbs. (8 Nm) Starter electrical connections Negative battery cable

2.4L & 2.5L Engines
  1. Remove or disconnect the following:
    Negative battery cable Air inlet tube Harness bracket Wiring at the starter Starter
To install:
  1. Install or connect the following:
    Starter and torque the bolts to 60 inch lbs. (7 Nm) Starter electrical connectors Harness bracket Air inlet tube Negative battery cable

2.4L Engine
  1. Remove or disconnect the following:
    Negative battery cable Air inlet tube Harness bracket Wiring at the starter Starter
To install:
  1. Install or connect the following:
    Starter and torque the bolts to 60 inch lbs. (7 Nm) Starter electrical connectors Harness bracket Air inlet tube Negative battery cable

2.5L Engine
  1. Remove or disconnect the following:
    Negative battery cable Air cleaner cover and duct Harness bracket Wiring at the starter Starter
To install:
  1. Install or connect the following:
    Starter and torque the bolts to 60 inch lbs. (7 Nm) Starter electrical connectors Harness bracket Air inlet tube Negative battery cable

3.5L Engines
  1. Remove or disconnect the following:
    Negative battery cable Air cleaner case (upper) and air cleaner to electric throttle control actuator tube. Harness protector from the harness Starter wiring at the starter Starter-to-engine bolts Starter from the vehicle

    42c548c.jpg
    Fig. Starter location and mounting detail-3.5L engine

continue...

Apr 05, 2010 | 1999 Nissan Altima

1 Answer

Changing alternator


REMOVAL & INSTALLATION
2.2L Engines
CHRYSLER ALTERNATOR
  1. Disconnect the negative battery cable.
  2. Label and disconnect the wiring (for easy installation).
  3. Remove the air conditioning compressor drive belt, if equipped.
  4. Loosen the alternator adjusting bracket bolt and adjusting bolt. Remove the alternator belt.
  5. Remove the bracket and mounting bolts.
  6. Remove the pivot bolt and nut.
  7. Lift the alternator from the vehicle.
When lifting the alternator out of the vehicle on some years with A/C, clearance may be restricted by the condenser cooling fan assembly or the A/C compressor and mounting bracket assembly, if so, removal of one of these items will be necessary.

To install:

  1. Position the alternator against the engine.
  2. Install the pivot bolt and nut.
  3. Install the mounting bracket bolts, and adjusting bolt.
  4. Install drive belts and adjust to specification.
  5. Tighten all the mounting bolts and nuts.
  6. Connect all alternator terminals.
  7. Connect the negative battery cable.

BOSCH ALTERNATOR

  1. Disconnect the negative battery cable.
  2. Disconnect the wiring and label for easy installation.
  3. Remove the air conditioning compressor drive belt.
  4. Loosen the alternator adjusting bracket locknut and adjusting screw. Remove the alternator belt.
  5. Remove the bracket locknut and mounting bolt.
  6. Remove the pivot bolt and nut.
  7. Remove the alternator from the engine.
To install:
  1. Position the alternator against the engine.
  2. Install pivot bolt and nut.
  3. Set the mounting bracket in place and install the bracket mounting bolt and locknut.
  4. Install the drive belts and adjust to specification.
  5. Tighten all the mounting bolts and nuts.
  6. Connect all alternator terminals.
  7. Connect the negative battery cable.

2.5L Engines
2.5L engines were equipped with either Chrysler or Bosch alternators.

  1. Disconnect the negative battery cable.
  2. Remove the drive belts.
  3. Remove the adjusting bracket-to-engine mounting bolt.
  4. Remove the adjusting locking bolt and nut, then remove the mounting bracket.
  5. Position the alternator to gain access to the wiring.
  6. Disconnect the wiring and label for easy installation.
  7. Remove the pivot bolt, nut, and washers.
  8. Remove the alternator assembly from the engine.
To install:
  1. Position the alternator assembly against the engine.
  2. Loosely install the pivot bolt, washers, and nut.
  3. Attach all wiring connectors to the alternator.
  4. Position the mounting bracket in place, then install engine mounting bolt.
  5. Loosely install the adjusting locking bolt and nut.
  6. Install the drive belts, and adjust to specification.
  7. Tighten all mounting bolts and nuts.
  8. Connect the negative battery cable.

2.6L Engines
2.6L engines were equipped with Mitsubishi alternators.
  1. Disconnect the negative battery cable.
  2. Disconnect the wiring and label for easy installation.
  3. Remove the adjusting strap mounting bolt.
  4. Remove the drive belts.
  5. Remove the support mounting bolt and nut.
  6. Remove the alternator assembly.
To install:
  1. Position the alternator assembly against the engine, then install the support bolt.
  2. Install the adjusting strap mounting bolt.
  3. Install the alternator belts and adjust to specification.
  4. Tighten all the support bolts and nuts.
  5. Connect all of the wiring terminals to the alternator.
  6. Connect the negative battery cable.

3.0L Engines
The 3.0L engines were equipped with either the Nippondenso or Bosch alternators.
  1. Disconnect the negative battery cable.
  2. Install a 1 / 2 in. breaker bar in the tensioner slot. Rotate counterclockwise to release belt tension and remove poly-V belt.
  3. Remove the alternator mounting bolts (2).
  4. Remove the wiring and remove alternator.
To install:
  1. Position the alternator onto the engine, then install the wiring.
  2. Set the alternator against the mounting bracket and install the mounting bolts.
  3. Rotate the tensioner counterclockwise and install poly-V belt.
  4. Connect the negative battery cable.

3.3L and 3.8L Engines
The 3.3L and 3.8L engines were equipped with the Nippondenso alternators.
  1. Disconnect the negative battery cable.
  2. Remove the alternator drive belt, by relieving the tension on the dynamic tensioner.
  3. Loosen the nut on the support bracket at the exhaust manifold, do not remove it.
  4. Remove the alternator tensioner/power steering bracket bolt.
  5. Remove the tensioner stud nut and remove the tensioner.
  6. Remove the alternator mounting bolts.
  7. Remove the power steering reservoir from the mounting bracket, do not disconnect the hoses, and position it out of the way.
  8. Remove the alternator support bracket bolts. Remove the intake plenum to alternator bracket bolt and remove the alternator support bracket from the engine.
  9. Remove the alternator from the engine and disconnect the electrical leads.
To install:
  1. Install the alternator in position on the engine and connect the electrical leads.
  2. Install the alternator support bracket, tighten the retaining bolts to 40 ft. lbs. (54 Nm).
  3. Install the power steering reservoir on the mounting bracket.
  4. Install the alternator mounting bolts, tighten the bolts to 40 ft. lbs. (54 Nm).
  5. Install the tensioner and tensioner mounting stud. Install the retaining nut on the exhaust manifold.
  6. Install the alternator belt, insert a 1 / 2 in. extension into the square hole in the tensioner and turn the tensioner. Tighten the tensioner bolt.
  7. Connect the negative battery cable.

Hope this help (remember comment and rated this).

Apr 01, 2010 | 1994 Dodge Caravan

2 Answers

How to pullout starter on 2000 gmc sierra 4 by 4


4.3L Engine
  1. Remove or disconnect the following:

    Negative battery cable Bracket and shield Wires Mounting bolts and shims Starter
To install:
  1. Install or connect the following:

    Starter Mounting bolts and shim. Torque the bolts to 33 ft lbs. (45 Nm). Wires. Torque battery wire nut to 89 inch lbs. (10 Nm) and ignition nut to 18 inch lbs. (2 Nm). Bracket and shield. Torque the nuts to 53 inch lbs. (6 Nm). Negative battery cable

    c5acb83.jpg
    Fig. Exploded view of the starter motor-4.3L engines.


  1. Remove or disconnect the following:

    Negative battery cable Bracket and shield Wires Mounting bolts and shims Starter
To install:
Install or connect the following:

Starter Mounting bolts and shim. Torque the bolts to 33 ft lbs. (45 Nm). Wires. Torque battery wire nut to 89 inch lbs. (10 Nm) and ignition nut to 18 inch lbs. (2 Nm). Bracket and shield. Torque the nuts to 53 inch lbs. (6 Nm). Negative battery cable

a557bbc.jpg
Fig. Exploded view of the starter motor-4.3L engines.

Hope help with this (remember rated and comment this).

Mar 17, 2010 | 2000 GMC Sierra

1 Answer

How to remove alternator from 1997 Chrysler Concorde?


e
3.3L Engine

  1. Disconnect the battery negative - cable.
b9a39c6.jpg

Fig. Wiring and nut locations



  1. Disconnect the alternator field circuit plug.
  2. Remove the B+ terminal nut and wire.
  3. Loosen the adjusting T-bolt, but do not remove it.
  4. Loosen the pivot bolt, but do not remove it either.
  5. Remove the alternator drive belt.
  6. Remove the adjusting T-bolt, pivot bolt, and mounting bolt, be careful not to loose the spacer.
  7. Remove the alternator.
To install:
  1. Attach the alternator to the support bracket. Tighten all bracket and alternator (except for the wiring nuts) bolts to 40 ft. lbs. (54 Nm).
  2. Install the B+ terminal nut and wire and tighten to 75 inch lbs. (9 Nm).
  3. Install the drive belt onto the alternator pulley. Make certain that the belt is seated correctly on the pulley.
  4. Connect the negative - battery cable.

3.5L Engine

  1. Disconnect the negative battery cable.
  2. Loosen the lower mounting bolt but do not remove it.
  3. Loosen the pivot bolt, but do not remove it.
3260271.jpg

  1. Loosen the belt adjusting bolt.
  2. Remove the alternator drive belt.
  3. Remove the bracket.
  4. Remove the lower mounting bolt and pivot bolt.
  5. Remove the alternator.
  6. Disconnect the alternator field circuit plug.
  7. Remove the B+ terminal nut and wire.
To install:
  1. Attach the alternator and bracket to the engine, then tighten the mounting bolts to 40 ft. lbs. (54 Nm).
  2. Install the drive belt onto the alternator pulley. Make certain that the belt is seated correctly on the pulley.
  3. Install and tighten the B+ terminal nut and wire to 75 inch lbs. (9 Nm) onto the new alternator.
  4. Connect the alternator field circuit plug.
  5. Connect the negative battery cable.
Hope helped with this (remember rated this help) Good luck.

Nov 03, 2009 | 1997 Chrysler Concorde

1 Answer

How do I jump the battery?


Hook up the red cable wire to the positive terminal on the battery of the car to be jumped, then hook up the other red jumper cable wire to the jumper vehicles red or positive terminal, it is recomended on the car to be jumped that you attach the negative cable to a metal bracket on the motor or body that can be attached securely (good connection), then attach the other last cable to the negative battery terminal, if you cannot find a suitable bracket to attache the negative cable to use the negative battery terminal. When doing all this try to keep the two ends of the cables seperated from each other, always wear safety glasses when working on auto batteries the can explode if a spark or flame gets too close to the top of the battery.

Jul 15, 2009 | 2003 Chevrolet Venture Passanger

1 Answer

Alternator Replacement


REMOVAL & INSTALLATION 3.3L Engine
  1. Disconnect the battery negative (-) cable.
  2. Disconnect the alternator field circuit plug.
  3. Remove the B+ terminal nut and wire.
  4. Loosen the adjusting T-bolt, but do not remove it.
  5. Loosen the pivot bolt, but do not remove it either.
  6. Remove the alternator drive belt.
  7. Remove the adjusting T-bolt, pivot bolt, and mounting bolt, be careful not to loose the spacer.
  8. Remove the alternator.
  9. To install:
  10. Attach the alternator to the support bracket. Tighten all bracket and alternator (except for the wiring nuts) bolts to 40 ft. lbs. (54 Nm).
  11. Install the B+ terminal nut and wire and tighten to 75 inch lbs. (9 Nm).
  12. Install the drive belt onto the alternator pulley. Make certain that the belt is seated correctly on the pulley.
  13. Connect the negative (-) battery cable.

Jun 24, 2009 | 1997 Chrysler LHS

1 Answer

Need to change the alternator


REMOVAL & INSTALLATION

3.3L Engine:
  1. Disconnect the battery negative - cable.
  2. Disconnect the alternator field circuit plug.
  3. Remove the B+ terminal nut and wire.
  4. Loosen the adjusting T-bolt, but do not remove it.
  5. Loosen the pivot bolt, but do not remove it either.
  6. Remove the alternator drive belt.
  7. Remove the adjusting T-bolt, pivot bolt, and mounting bolt, be careful not to loose the spacer.
  8. Remove the mounting bolt.
  9. Remove the spacer & washer
  10. Remove alternator.
To install:
  1. Attachthe alternator to the support bracket. Tighten all bracket andalternator (except for the wiring nuts) bolts to 40 ft. lbs. (54 Nm).Install the B+ terminal nut and wire and tighten to 75 inch lbs. (9 Nm).
  2. Install the drive belt onto the alternator pulley. Make certain that the belt is seated correctly on the pulley.
  3. Connect the negative - battery cable.
-------------------------------------------------------------------------------------------------
3.5L Engine:
  1. Disconnect the negative battery cable.
  2. Loosen the lower mounting bolt but do not remove it.
  3. Loosen the pivot bolt, but do not remove it.
  4. Loosen the belt adjusting bolt.
  5. Remove the alternator drive belt.
  6. Remove the bracket.
  7. Remove the lower mounting bolt and pivot bolt.
  8. Remove the alternator.
  9. Disconnect the alternator field circuit plug.
  10. Remove the B+ terminal nut and wire.
To Install:
  1. Attach the alternator and bracket to the engine, then tighten the mounting bolts to 40 ft. lbs. (54 Nm).
  2. Install the drive belt onto the alternator pulley. Make certain that the belt is seated correctly on the pulley.
  3. Install and tighten the B+ terminal nut and wire to 75 inch lbs. (9 Nm) onto the new alternator.
  4. Connect the alternator field circuit plug.
  5. Connect the negative battery cable.
If you need photos to follow then try this link...
http://www.autozone.com/shopping/repairGuide.htm?pageId=0900c1528006a83e

Jan 20, 2009 | 1999 Dodge Intrepid

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

17 people viewed this question

Ask a Question

Usually answered in minutes!

Top Subaru Experts

yadayada
yadayada

Level 3 Expert

75797 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8140 Answers

Are you a Subaru Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...