Question about 2005 Cadillac CTS

1 Answer

Need to replace rt turn signal lamp on 2005 cts

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Governor:

    An expert whose answer got voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 68 Answers

I just replaced front turn signal bulb. Since all of them (signal and fog lamps) are integrated with the bumper, you have to do that from beneath. First ,turn your wheels to the max right.Inside the arch you'll see that it is covered by plastic shield.You will have to remove plastic clips on the sides of that shield.There are six of them and they are clearly visible.Be careful not to brake clips.Use flat screwdriver to pull hat first,then the whole clip can be removed with fingers.Once all six clips pulled out,plastic shield will almost fall by itself - no efforts needed to detach it. That's it - you've got the access to your signal and fog lamps.

Removing the tire and blocking the front end first with jack stands makes the access much better

Posted on Mar 20, 2011

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Turn signal not working or 4 way flasher


Did you check your fuses to the turn signals and the flasher.They may need to be replace? Plus check all your bulbs make sure there is no burnt ones.If there are then you need to replace them. Hope this helps?

Apr 19, 2015 | 2005 Cadillac CTS

1 Answer

2010 chevy equinox right rear turn signal doesnt work, replaced bulb and still the same. front works, is there a fuse for the rear light and where is the fuse located.


RT/SIG fuse #11 15amp - I/P fuse box . Fuse Block - I/P
In the center of the instrument panel, beneath the right side of the radio, in back of the right side console access panel.
This fuse is power to the BCM , When you put on the right turn signal , this is a voltage signal to the BCM . With logic ( programming ) the BCM then controls the turn signal !
Turn Signal/Hazard Lamps
The body control module (BCM) is responsible for controlling the turn signals and hazard lamps. When the turn signal switch is placed in either the left turn or right turn position, the BCM receives a signal from the turn signal switch. The BCM then sends an on-off voltage signal to either the left or right turn signals and their instrument panel cluster (IPC) indicator. When the hazard switch is pressed, the BCM receives a signal from the hazard switch. The BCM then will send an on-off voltage signal to all the turn signal lamps. All the turn signal lamps will flash including both IPC turn signal indicators.
There could be a DTC- diagnostic trouble code stored in the BCM pointing to the problem ! I suggest you take your vehicle to the dealer or a ASE certified repair shop that has the diagnostic tools to find the problem . Just so you don't waste your money replacing parts that don't fix it.
There could

Dec 14, 2012 | 2005 Chevrolet Equinox

3 Answers

Only Rt turn signal works no matter if switch is in Lt or Rt position


The multi-function switch could be defective. The L/R position signals go to the instrument cluster then they are bussed on computer data lines to the front control module to develop the outputs that light the turn lamps. The defect could be in the instrument cluster, the front control module, or even the PCM

Nov 05, 2012 | 2008 Mitsubishi Raider

1 Answer

My rt turn signal on my 2005 sts does not work. i replaced th bulb, and checked the but that didn't fix it. what else could it be?


After you replace the bulb you would check the socket for power on that wire and for a ground. If there is no power on the circuit you would then check the turn signal switch.

Sep 29, 2012 | Cadillac Cars & Trucks

1 Answer

2009 Impala rear lights not working


Turn Signal Lamps
The LT T/SIG and RT T/SIG fuses located in the underhood fuse block supplies battery positive voltage to the body control module (BCM) for turn signal and hazard lamp operation. When the turn signal switch is place in either the LEFT or RIGHT position, ground from G202 is applied through the turn signal switch signal circuit to the BCM indicating the turn signal request. In response to this signal, the BCM applies a pulsating voltage to the front and rear turn signal lamps supply voltage circuits cycling the lamps ON and OFF. The BCM also sends a message via GMLAN to the instrument panel cluster (IPC) to cycle the turn signal indicator ON and OFF depending on the position of the turn signal switch.
Ground for the turn signal lamps is supplied as follows:
• G101 provides ground for the left front turn signal lamp
• G100 provides ground for the right front turn signal lamp
• G302 provides ground for the left and right rear turn signal lamps

The LT T/SIG and RT T/SIG fuses located in the underhood fuse block are also used by the body control module (BCM) for stop lamp operation.
The brake pedal position sensor is used to sense the action of the driver application of the brake pedal. The body control module (BCM) provides both, a 5-volt reference voltage and low reference to the brake pedal position sensor. The position sensor provides an analog voltage signal back to the BCM that will increase as the brake pedal is applied. When the brake pedal is applied, the BCM will then apply battery voltage to the left and right stop lamp supply voltage circuits and the center high mounted stop lamp (CHMSL) supply voltage circuit illuminating the stop lamps. At the same time the BCM signals the transmission control module (TCM) and the engine control module (ECM) that the brakes are applied. Ground for all stop lamps is provided at G302.
The stop lamps on this vehicle will not illuminate unless the ignition is in the accessory, run, or crank positions. When the ignition is in the OFF position the stop lamps will not illuminate when the brake pedal is applied.

Did you check the fuse's. ? Wouldn't think it's a ground because right an left tail lamp Assembly's use same ground ! Did you check for B+ voltage at the bulb. with a volt meter ? Power is supplied by the BCM . Could be the tail lamp assembly

Jul 19, 2017 | Cars & Trucks

1 Answer

Back lights dont work


check stop lamp 15 amp fuse. if fuse okay either brake light switch is bad or turn signal switch is faulty that is a dealership fix.

Jan 26, 2012 | 2005 Cadillac CTS

1 Answer

I am trying to replace aleft rear turn signal bulb on a 2005 lacrosse. I removed two wing nuts but cannot remove assmbly. Is there another wing nut holding it in. I cannot find it?


3 wing nuts. here is the info needed.

gmlogoflat.gif Service Information
bhome.gifbpublication.gifbnumsrchbutton.gifbnews.gifymkbutton.giffeedback.gifbhelp.gif
2005 Buick LaCrosse ' Allure, LaCrosse VIN W Service Manual ' Body ' Lighting Systems ' Repair Instructions ' Document ID: 1537542 Tail Lamp, Turn Signal Lamp, High Mount Stop Lamp, License Lamp, Backup Lamp Replacement - Rear
1537540.gif
tif.gif
Callout
Component Name
Notice: Refer to Fastener Notice in the Preface section.
Fastener Tightening Specifications: Refer to Fastener Tightening Specifications .
Turn Signal/Stop Lamp Assembly Replacement - Rear 1
Nut, Turn Signal/Tail Lamp (Qty: 3)
Tip
Pull back rear compartment carpet to gain access to lamp.
Tighten
2 N·m (18 lb in)
2
Lamp, Turn Signal/Tail Lamp
Tip
Twist the bulb socket and pull inward to replace the bulb.
License Lamp Replacement 3
Screws, License Lamp (Qty: 2)
Tighten
2 N·m (18 lb in)
4
Lamp, License Lamp
Tip
Twist the bulb socket and pull inward to replace the bulb.

Jul 29, 2011 | Buick LaCrosse Cars & Trucks

1 Answer

Turn signal don,t turn on lf rt


are you refering to when you turn the signal on and the steering wheel returns, the switch needs to be manualy turned off? if this is the case the the switch itself needs to be replaced. there is no "repair". cheers

Dec 23, 2009 | 2005 Land Rover Range Rover

2 Answers

I have a 2005 Cadillac CTS. Both my brake lights went out and don't work. Turn signal works. Could it be my brake actuator that isn't working or something else? thank you


Check the fuse and see if it isn't blown, if it is good, check the brake switch, it's near the top of the brake pedal on the back side.

Apr 08, 2009 | 2005 Cadillac CTS

1 Answer

1995 chrysler lebaron


Here's what mine says- for a 95 Chysler LeBaron GTC Convertible. I didn't see anything about a fuel pump, but maybe it's connected to something else? I dunno. Good luck. Here's the info at least.
1 HTR-AC 30A, 2 POWER WINDOWS 30A C/B, 3 PWR SEAT, LKS, TOP 30 A C/B, 4-BLANK, 5 BACK-UP LAMPS 20A, 6 TURN SIGNAL 20A, 7 REAR WIPER 20A, 8 ILLUM LAMPS 5A, 9 INTERIOR LAMPS 10A, 11 CIGAR LIGHTER 20A, 12 RS AMO 20A, 13 INTERIOR LAMPS 10A. 14 BOD COMP MESS CTR 5A, 15 SPEED CONTROL 2A, 16 GAUGES AIRBAGS 5A, 17 STOP LAMPS 18 HEAD LAMP RT-LOW 10A, 19 HEATED MIRRORS 5A, 20 AIRBAGS 5A, 21 STOP LAMOS 20A, 22 HORN 20A, 23 RT-TAIL LAMP-EUR 5A, 24 LT-TAIL LAMP EUR 5A, 25 HEAD LAMP LT-HI 10A, 26 HEAD LAMP RT-HI 10A, 27 RADIO 104, 28 FRONT WIPER 20A

Mar 29, 2009 | 1995 Chrysler LeBaron

Not finding what you are looking for?
2005 Cadillac CTS Logo

192 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cadillac Experts

yadayada
yadayada

Level 3 Expert

75817 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8180 Answers

Are you a Cadillac Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...