Question about 1992 Oldsmobile Cutlass

1 Answer

How to remove the wire track cover from front of engine 3300 to remove and replace ignition wires

Posted by on

  • Anonymous Sep 17, 2008

    I haven't looked at the service manual but I have to do this same repair. I'm pretty sure you need to take that motor mount bracket off the top of the engine to do it.

  • Anonymous Nov 29, 2008

    I have the same problem trying to replace ignition wires for the left two wires/ drivers side. How do you remove the cover underneath the top engine mount with out breaking it?

×

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

On that plastic strip there are two small clips under the block that have to be unlatched before you can rotate the plastic strip upwards and then off. Even knowing this it is a large pain to remove. Be carefull the plastic clips tend to break off.

Posted on Jan 17, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where is the spark plugs located for the 2002 4 cylinder highlander located. Plan on replacement.


First, remove the no. 1 engine cover. Locate the ignition coils, these will be squarish-looking packs with spark plug wires (4 of them) coming out. The wires should be going to the spark plugs, which are on the front and back side of the engine.
Grab the ignition coils or spark plug wires by the thick plastic piece at the end of the wire. Squeeze the end and turn it to release it from the spark plug. Pull back to remove the plug from the engine.
Slide the spark plug socket over the spark plug. The most common size of spark plug socket used on a Toyota Highlander is 16mm. Turn the socket to the left to unscrew and remove the spark plug from the cylinder well.

Mar 07, 2011 | 2002 Toyota Highlander

1 Answer

Describe your how fix my pontiac 2000 montana Problem changing spark plugs



Inspection

Inspect for the correct routing of the spark plug wires. Improper routing may cause cross-firing. Inspect each wire for any signs of cranks or splits in the wire. Inspect each plug wire boot for tearing, piercing, arcing, carbon tracking or a corroded terminal.
If there is any corrosion, carbon tracking or arcing indicated on a plug wire boot or terminal, both the plug wire and component it was connected to should be replaced.


Removal & Installation

3.5L Engine

  1. Before servicing the vehicle, refer to the Precautions Section.
  2. Remove the left side spark plug wires from the spark plugs.
  3. Remove the left side plug wires from the retaining clips.
  4. Rotate the engine for access as follows:
    1. Set the parking brake.
    2. Shift the transaxle into neutral.
    3. Remove the engine mount strut bolts. Swing the engine mount struts aside.
    4. Install the Engine Tilt Strap J-41131.
    5. Pull on the engine in order to rotate the engine forward.
    6. Tighten the strap.

  5. Remove the right side spark plug wires from the spark plugs.
  6. Remove the plug wires from the retaining clip.
  7. Remove the spark wires from the ignition coils.
  8. Remove the plug wire assembly from the engine.
    NOTE If you are replacing the spark plug wires, the spark plug wire conduit and retaining clips should be transferred to the replacement wires.

To install:
  1. Install the right side plug wires to the ignition coils and then the spark plugs.
  2. Install the spark plug wires to the retaining clip.
  3. Rotate the engine back to the original position.
  4. Install the left side spark plug wires to the ignition coils and then to the spark plugs.
  5. Install the spark plug wires to the retaining clips.

3.9L Engine
  1. Before servicing the vehicle, refer to the Precautions Section.
  2. Remove the intake manifold cover.
  3. Remove the left side spark plug wires as follows:
    1. Disconnect the left side spark plug wires from the spark plugs.
    2. Disconnect the left side spark plug wires from the ignition coil.
    3. Remove the left side spark plug wire clips from the intake manifold and heater inlet and outlet pipe.
    4. Remove the left side spark plug wire assembly.

  4. If removing the right side spark plug wires, the engine must be rotated for access as follows:
    1. Set the parking brake.
    2. Shift the transaxle into neutral.
    3. Remove the engine mount strut bolts. Swing the engine mount struts aside.
    4. Install the Engine Tilt Strap J-41131.
    5. Pull on the engine in order to rotate the engine forward.
    6. Tighten the strap.

  5. After rotating the engine, remove the right side spark plug wires as follows:
    1. Disconnect the right side spark plug wires from the spark plugs and ignition coil.

  6. Remove the right side spark plug wire clip from the ignition coil bracket.
  7. Remove the right side spark plug wire assembly.

To install:
  1. Install the spark plug wire assembly.
  2. Install the right side spark plug wire clip at the ignition coil bracket.
  3. Connect the plug wires to the ignition coil and spark plugs.
  4. If the engine was rotated for access, return the engine to the original position.
  5. The remainder of the installation is the reverse order of removal.

Feb 05, 2011 | 2000 Pontiac Montana

2 Answers

How do I replace the ignition coil in my 2002 ford taurus



Removal & Installation

3.0L (VIN S) Engine

  1. Disconnect the negative battery cable.
  2. Unplug the engine control sensor wiring connectors from the ignition coil and the radio ignition interference capacitor.
  3. Tag and disconnect the spark plug wires from the coil by squeezing the locking tabs, then twist the tab and pull upwards.
  4. Unfasten the four ignition coil retainers and remove the coil and the coil ground wire the radio ignition interference capacitor. Save the capacitor and coil ground wire for re-installation of the coil assembly.
  5. Wipe the coil towers with a clean cloth dampened with soap and water. Remove any soap film and dry with compressed air. Inspect the coil for cracks, carbon tracking, dirt or damage and replace as necessary.

    0996b43f802333d8.jpg enlarge_icon.gifenlarge_tooltip.gif

    Fig. Ignition coil assembly mounting-3.0L DOHC engines


To install:
  1. Place the coil, capacitor and the coil ground wire onto its mounting location on the right hand valve cover.
  2. Install the coil assembly retainers and tighten to 45-61 inch lbs. (5-7 Nm)..
  3. Apply dielectric compound D7AZ-19A331-A or its equivalent to the spark plug wire boots.
  4. Attach the spark plug wires to their proper terminals on the coil and make sure the boots are firmly seated so that the locking tabs engage.
  5. Attach the engine control wiring connectors to the ignition coil and the radio ignition interference capacitor.
  6. Connect the negative battery cable, start the vehicle and check for proper operation.

Dec 19, 2010 | 2002 Ford Taurus

1 Answer

Need change plugs on 99 grand marquis gs how do i remove coil .do P meed to dopressurize anyting


Ford Crown Victoria, Mercury Grand Marquis, Marauder, Lincoln Town Car 1999-2005

Ignition Coil - Removal & Installation
  1. Disconnect the negative battery cable.
  2. Disengage the TFI-IV harness or the engine control sensor wiring connector from the ignition coil, as applicable.
  3. On the 3.8L engine, disengage the engine control wiring connector from the radio ignition interference capacitor.
  4. Remove the ignition coil retaining screws and the ignition coil and radio interference capacitor (if equipped) from the ignition coil mounting bracket.
e6622a7.jpg

Fig. Ignition coil and related components-late model 3.8L shown

79c5948.jpg

Fig. Remove the ignition coil retaining screws

353f142.jpg

Fig. If your coil has this kind of build-up, it needs a good cleaning

a2c1928.jpg

Fig. This is the coil wire. Replace it if it looks like this
  1. Remove the ignition coil cover from the ignition coil by releasing the locking tabs on both sides of the cover, then remove the ignition coil.
To install:
  1. Install the ignition coil, then attach ignition coil cover, making sure the cover is firmly in place.
  2. If removed, connect the ignition coil and radio interference capacitor, then install the ignition coil retaining screws. Tighten the retaining screws to 25-35 inch lbs. (3-4 Nm).
  3. Connect the coil wire, then engage any electrical connectors that were removed.
  4. Connect the negative battery cable.

Hope help with this (remember rated this post). TY for using Fixya.

May 19, 2010 | 1999 Mercury Grand Marquis

1 Answer

How involved it distributor removal and


it is very easy-for starters there is no distributor,it has an ignition module which is located on the right side off the engine in front-just follow the spark plug wires.the plugs are very easy to get to. on an sl1 the plugs are right below the valve cover-just remove the plug wires and replace the plugs and probably wire also-unless the coils are bad(corroded)you shouldnt have to replace the ignition module.

May 01, 2010 | 2000 Saturn SL

2 Answers

Where is the ignition control module on an 1989 totota camry


Toyota Camry 1983-1996 Repair Guide Ignition Module - REMOVAL & INSTALLATION

External
All engines, except the 2S-ELC, have an external igniter.
  1. Turn the ignition key to the OFF position. Disconnect the negative battery cable.
  2. Separate the wiring harness connections.
  3. Unbolt the igniter.
  4. Loosen the nut holding the wire lead onto the coil.
  5. Tag and disconnect the wire lead.
  6. Lift the igniter off its mount.

To install:
  1. Mount the igniter to the bracket.
  2. Attach the wire lead to the coil.
  3. Connect the harness.
  4. Connect the negative battery cable. Reset any digital equipment such as radio memory and the clock if necessary.

Internal
REMOVING IGNITER WITH DISTRIBUTOR
See Figure 1
The internal igniter is only applicable to 2S-ELC engine Camry models. All other engines are equipped with an external igniter assembly.
Review the complete service procedure before this repair. Note position, color of wire and routing of all internal distributor assembly wiring.
  1. Disconnect the cable from the negative battery terminal.
  2. Remove the number one spark plug. Place a finger over the spark plug hole and rotate the crankshaft clockwise to top dead center. When there is pressure felt on the finger at the spark plug hole, this will be top dead center of the compression stroke on number one cylinder. If not, repeat the procedure. Install the number one spark plug.
  3. Mark the position of the distributor flange in relation to the camshaft housing. Remove the IIA distributor assembly.
  4. Remove the distributor cap with the wires attached, and remove the packing. Mark the position of the rotor relative to the housing and pull the rotor straight up and off the shaft. The distributor cap is held to the housing with three retaining screws.
  5. Remove the ignition coil dust cover.
  6. Remove the two nuts and spring washers and disconnect the four wires from the terminals on the side of the ignition coil. The wires are color coded yellow, blue, brown and red.
  7. Remove the four retaining screws and remove the ignition coil and packing.
  8. Remove the nuts and disconnect the pink, white and black wires from the igniter terminals. Remove the two igniter retaining screws and remove the igniter.

To install:
  1. Attach the new igniter with the two retaining screws. Connect the pink, black and white wires to their respective terminals and install the nuts. Make sure that the pick-up coil wires are secured in their clips and that there is slack in the wires.
  2. Install the ignition coil and attach it with the four retaining screws.
  3. Connect the four ignition coil wires to their respective terminals and install the two nuts and spring washers.
  4. Install the coil dust cover and push the rotor onto the shaft.
  5. Place the distributor cap and wires into position. Install and tighten the retaining screws.
  6. Install the distributor assembly and connect the negative battery cable.
  7. Connect a tachometer and timing light to the engine and adjust the ignition timing.

71948a0.jpg

Fig. 1: Make sure you remember where the colored wires attach for installation-2S-ELC engine
  1. Reset any digital equipment such as radio memory and the clock if necessary.

REMOVING IGNITER WITHOUT REMOVING DISTRIBUTOR
  1. Remove the distributor cap, rotor and di-electric insulator covers. Disconnect the red and yellow wires from the coil and the pink, white and black wires from the igniter.
  2. Remove the igniter. It may be necessary to mark and rotate the distributor to gain access to the igniter retaining screws. The timing should be checked after the distributor is returned to the mark.

To install:
  1. Install the new igniter using the two new retaining screws.
  2. Twist the pick-up coil wires together, install the white wire first then pink and black wires to their original locations. Make sure the wires do not touch the housing generator or advance plate.
  3. Route the red and yellow wires from the igniter so they do not contact moving parts. Connect the red wire to the right coil terminal (with the brown wire) and the yellow wire to the left terminal (with the blue wire). Replace the covers, rotor and cap.
  4. Connect a tachometer and timing light to the engine and adjust the ignition timing.

Hope this helped (remember comment and rated this).

Apr 05, 2010 | 1989 Toyota Camry

1 Answer

How to replace the starter


Toyota Celica, Corolla, ECHO & MR2 1999-05
Starter - Removal & Installation

1. Before servicing the vehicle, refer to the Precautions section.
2. Remove or disconnect the following:
Radiator upper support seal
Air cleaner
Engine under covers
Starter wiring
Starter

3. Installation is the reverse of removal. Torque the bolts to 28 ft. lbs. (37 Nm). Note that the bolts are 2 different lengths.


1. Before servicing the vehicle, refer to the Precautions section.
2. Remove or disconnect the following:
Battery and tray. On models equipped with an air bag, work must NOT be started until at least 90 seconds have passed from the time that both the ignition switch is turned to the LOCK position and the negative cable is disconnected from the battery.
Coolant reservoir
Reservoir hose from the radiator
Right side under cover
Wiring clamp
Wiring from the starter
Starter


To install:
1. Install or connect the following:
Starter
Starter wiring and nut
Starter connector and wire clamp
Right side engine cover
Radiator reservoir and hose
Battery and tray

2. Check the cooling system and top off if necessary.


1. Before servicing the vehicle, refer to the Precautions section.
2. Remove or disconnect the following:
Negative battery cable. On models equipped with an air bag, work must NOT be started until at least 90 seconds have passed from the time that both the ignition switch is turned to the LOCK position and the negative cable is disconnected from the battery
Engine under covers
Wiring from the starter terminals
Starter mounting bolts
Starter


To install:
1. Install or connect the following:
Starter
Starter wiring
Engine under covers


1. Before servicing the vehicle, refer to the Precautions section.
2. Remove or disconnect the following:
Negative battery cable
Front engine undercover
Starter wiring harness connectors
Starter mounting bolts
Starter motor


To install:
1. Install or connect the following:
Starter motor. Tighten the bolts to 28 ft. lbs. (37 Nm).
Starter wiring harness connectors
Front engine undercover
Negative battery cable

Hope help with this (remember rated and comment).

Mar 11, 2010 | 2003 Toyota Corolla

1 Answer

I need the diagram to put the spark plug cables


2003 Chevrolet Malibu 3.1L SFI OHV 6cyl
Spark Plug Wires - Removal & Installation

3.5L Engine
  1. Before servicing the vehicle, refer to the Precautions Section.
    NOTE Twist the spark plug boot one-half turn in order to release the boot. Pull on the spark plug boot only. Do not pull on the spark plug wire or the wire could be damaged.
  2. Remove the intake manifold cover, if required.
  3. Disconnect the left side spark plug wires from the spark plugs.
  4. Disconnect the left side spark plug wires from the ignition coil.
  5. Remove the spark plug wire clips from the Manifold Absolute Pressure (MAP) sensor bracket and the heater inlet and outlet pipe tab.
  6. Remove the spark plug wire assembly.
  7. If replacing only one plug wire, open the retaining clips and remove the appropriate spark plug wire.
  8. Disconnect the right side spark plug wires from the spark plugs.
  9. Disconnect the right side spark plugs from the ignition coils.
  10. Remove the spark plug wire assembly.
  11. If replacing only one plug wire, open the retaining clip and remove the appropriate spark plug wire.
To install:
  1. Install the spark plug wire assembly.
  2. Connect the right side spark plugs to the ignition coils.
  3. Connect the right side spark plug wires to the spark plugs.
  4. If replacing only one plug wire, open the retaining clip and install the appropriate spark plug wire.
  5. Install the spark plug wire assembly.
  6. Connect the left side spark plug wires to the spark plugs.
  7. Connect the left side spark plug wires to the ignition coil.
  8. Install the spark plug wire clips to the MAP sensor bracket and the heater inlet and outlet pipe tab.
  9. If replacing only one plug wire, open the retaining clips and install the appropriate spark plug wire.
  10. Install the intake manifold cover, if required.

Fig. 2.2L Engine Firing Order: 1-3-4-2 Distributorless ignition system
74d742b.jpg


Fig. 3.1L Engine Firing order: 1-2-3-4-5-6 Distributorless ignition system
306b531.jpg


Fig. 3.5L Engine Firing order: 1-2-3-4-5-6 Distributorless ignition system
9313fa7.jpg


Fig. 2.4L Engine Firing order: 1-3-4-2 Distributorless ignition system
2c9af72.jpg


Fig. 3.1L Engine Firing order: 1-2-3-4-5-6 Distributorless ignition system
d929c16.jpg


Fig. 2.2L Engine Firing Order: 1-3-4-2 Distributorless ignition system
f357cd3.jpg

Fig. 3.5L & 3.9L Engines Firing order: 1-2-3-4-5-6 Distributorless ignition system
09e9db9.jpg

I really hope help you with this (remember rated this help) Good luck.

Sep 23, 2009 | 2003 Chevrolet Malibu

3 Answers

Coil pack. what and where is it? what does it look like?



 
 
Ignition Coil
Removal & Installation
4.2L Engine
1997-2000
To Remove:

Before servicing the vehicle refer to the precautions at the beginning of this section.
Remove or disconnect the following:
The ignition coil electrical connector
The radio ignition interference capacitor connector
The locking tabs
The six ignition wires, marking for reinstallation
The brackets
The spark plug wire set
CAUTION
Spark plug wires must be connected to the proper ignition coil terminal. Mark spark plug wire locations before removing them.
The accelerator cable bracket nut
The accelerator cable bracket bolt
The accelerator cable bracket and position it aside.
The two ignition coil nuts
The ignition coil stud bolt
The ignition coil
To Install:
Install or connect the following:
The ignition coil
The two ignition coil nuts
The ignition coil stud bolt
Torque to: 71-98 inch-lbs (8-11 Nm)
The accelerator cable bracket
The accelerator cable bracket nut
The accelerator cable bracket bolt
Torque to: 71-98 inch-lbs (8-11 Nm)
The ignition coil electrical connector
The radio capacitor connector


CAUTION
The Spark plug wires must be connected to the proper ignition coil terminal.
Squeeze the locking tabs and connect the six ignition cables.
2001-2003
To Remove:

Before servicing the vehicle refer to the precautions at the beginning of this section.
Remove or disconnect the following:
The ignition coil electrical connector
The spark plug wires, marking for reinstallation
CAUTION
The sparkplug wires must be connected to their correct ignition coil terminal.
The ignition coil
The bolts
Inspect the ignition coil for carbon tracks or damage.
To Install:
Inspect the ignition coil for carbon tracks or damage.
Install or connect the following:
The ignition coil
The bolts
Torque to: 53 inch-lbs (6 Nm)
The ignition coil electrical connector
The spark plug wires, in their original positions
4.6L Engine
1997-1999
To Remove:

NOTE: This procedure is for either RH or LH ignition coil.
Before servicing the vehicle refer to the precautions at the beginning of this section.
Remove or disconnect the following:
The ignition coil electrical connector
The radio capacitor electrical connector
The spark plug wires by squeezing the locking tabs (four each side)
CAUTION
The spark plug wires must be connected to their proper ignition coil terminal. Mark spark plug wire locations.
The bolts
The ignition coil
To Install:
NOTE: The procedure is for either LH or RH ignition coil
Install or connect the following:
The ignition coil
The bolts
Torque to: 44-62 inch-lbs (5-7 Nm)
The ignition coil electrical connector
The radio capacitor electrical connector
The spark plug wires (four each side), into their original positions by squeezing the tabs


CAUTION
The spark plug wires must be connected to their proper ignition coil terminal.

 
Top of Form 1
Bottom of Form 1

Mar 28, 2009 | 1998 Ford F150 Regular Cab

1 Answer

Replacing the plug wires


You may have a cover over the engine that has 3.3 on it; if so twist the lower half of the oil fill tub and remove it and pick up cover to exspose top of motor. this cover is a big plastic cover.

Nov 20, 2008 | 1992 Oldsmobile Cutlass Ciera

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

38 people viewed this question

Ask a Question

Usually answered in minutes!

Top Oldsmobile Experts

yadayada
yadayada

Level 3 Expert

60792 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6811 Answers

Are you an Oldsmobile Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...