Question about 1991 Mercury Tracer

1 Answer

Hi, my brake lights stopped working. i changed the bulbs and harnesses. what else can i do

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Expert
  • 86 Answers

Replace the brake switch, usually located under drivers side dash, on or very near brake pedal.

Posted on Mar 20, 2011

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Location of brake light switch fault on 2002 discovery freelander


The brake light switch is on top of brake pedal arm. Check your bulbs, and connections to the rear lights (unplug harnesses and clean the connectors as well as bulb(s) etc... )

Also, it (shouldn't) be the brake light switch if you can shift out of park. Good luck.

Sep 13, 2014 | 2002 Land Rover Discovery Series II

2 Answers

2007 chevy impala brake light and left turn signal not working


Fast flashing dash signals mean there is a bulb issue-DEFINATELY!

Aug 07, 2012 | 2007 Chevrolet Impala LS Sedan New Cars

2 Answers

I have a 2006 Chevy Silverado 1500 4wd, and both of my brake lights stopped working, but the light above the bed of the truck still works. I have checked all the fuses, changed the bulbs, and checked the...


well it sounds like you have a short fro junction block to taillights , make your own wire from where you know you have power to brake lights . and that will tell you where to go.

Feb 13, 2011 | Chevrolet Silverado 1500 Cars & Trucks

1 Answer

The lower brake lights have stopped working yet the upper brake light above rear window works Doesn't appear to be burnt bulbs. I removed a trailer wiring harness that was connected to a connector on the...


No you cannot just connect the 3rd brake light to the left/right brake light, chances are they also function independently as turn signals. The type of trailer wiring harness you speak of is usually installed by unplugging the wiring harness and plugging that connector inline. The two sides of that harness should plug back together.

Oct 14, 2010 | Chevrolet Venture Cars & Trucks

2 Answers

I have a 2000 Dodge RAM 3500 with no lower brake lights. The turn signals work and the hazard lights work so the bulbs are good. The center high mounted stop lamp works but just in case I replaced the...


if the third brake light works then ther is a broken wire. start looking for it at the tail lights and work forward if you cant find the break you can always run a new possitive wire from either the third brake light to the tail lights or if the trailer wiring harness hase power to the brake lights you can splice in there as well. hope this helps

Mar 14, 2010 | 1994 Dodge Ram

4 Answers

Brake lights won't work. tail lights do. I


need to know if your third brake light up high is working or not.if it isn't,you need to check the brake light switch on the brake pedal with a test light,one side hot all the time,the other side should turn hot when brake pedal is pushed.

Jan 19, 2010 | 2002 GMC Envoy XL

1 Answer

My Stop lights are not working.


The brake system error code is for a faulty master cylinder. check the cylinder function and check your brake fluid level as well. the master cylinder is located on the fire wall directly in line with the steering wheel under the hood. the brake fluid reservoir is located and attached to the master cylinder on top. check the master cylinder and fluid thoroughly.

Concerning the brake lights, you will need to inspect the wiring harness in the trunk or back hatch. make sure the brake light wiring harnesses is in good condition. check the bulb housing as well.

replace the brake light wiring harness if found to be faulty.

May 25, 2009 | 2003 Dodge Durango

1 Answer

Brake lights


Hi,

Usual suspects would be:
1. bulbs;
2. brake light switch;
3. rear harness connector;
4. loose grounding of rear lights assembly.

Hope this be of initial help/idea. Pls post back how things turned up or should you need additional information.

Good luck and kind regards.

Thank you for using FixYa.

Jul 12, 2008 | 2000 Jeep Cherokee 2WD

Not finding what you are looking for?
1991 Mercury Tracer Logo

76 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mercury Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

fordexpert

Level 3 Expert

5501 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Are you a Mercury Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...