Question about 2004 Honda Odyssey

2 Answers

Torque settings whats the torque settings for the head bolts ?

Posted by on

2 Answers

  • Level 1:

    An expert who has achieved level 1.

    MVP:

    An expert that got 5 achievements.

    Greenhorn:

    A rookie expert who has answered 20 questions on their first day.

    Night Owl:

    An expert who has answered 10 or more questions between 12 midnight and 6am on the same day.

  • Contributor
  • 21 Answers

Usualy taken up in three stages 30,50,65 foot punds dont use the small torque wrench because that is in inch pounds. Cheers

Posted on Mar 03, 2013

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that has over 10 points.

    Mayor:

    An expert whose answer got voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 19 Answers

  1. Tighten the cylinder head bolts sequentially in three steps. NOTE: Perform each step twice. 1st step torque: 39 Nm (4.0 kgf-m, 29 ft. lbs.) 2nd step torque: 69 Nm (7.0 kgf-m, 51 ft. lbs.) 3rd step torque: 98.1 Nm (10.0 kgf-m, 72.3 ft. lbs.) Use a beam-type torque wrench. When using a preset-type torque wrench, be sure to tighten slowly and not to overtighten. If a bolt makes any noise while you are torquing it, loosen the bolt, and retighten it from the first step.

Posted on Aug 06, 2008

6 Suggested Answers

  • 2 Answers

SOURCE: what is the 98 isuzu rodeo head bolt torque

joyce, there are different specs for sohc and dohc engines. my advice is to get a Haynes manual from the auto parts store.

doug

Posted on Sep 01, 2008

  • 1 Answer

SOURCE: Angle Torque settings head bolts

Use new bolts, tighten in the following stages 1. 20Nm 2. 100Nm 3. wait 3 mins 4. slacken bolts 1&2 retighten to 20Nm +110 degrees 5. carry out stage 4 for bolts 3,4,5 & 6 then bolts 7,8,9 &10 Sequence, 8 4 1 5 9 7 3 2 6 10 Bolts 9 & 10 are flywheel side of the engine.

Posted on Mar 17, 2009

the terrier
  • 94 Answers

SOURCE: head bolts torque settings

according to the manual its 22NM or 16lb/ft

Posted on Oct 26, 2008

SOURCE: need torque settings for honda ballade cylinder

dear friend-your torque setting is cold 66 nm

Posted on Jul 23, 2009

  • 12 Answers

SOURCE: head bolt torque specs for 200 honda accord 3.0

its a three step process 1st 29ft/lbs 2nd 51ft/lbs 3rd 72.3ft/lbs

Posted on Apr 25, 2010

  • 1 Answer

SOURCE: golf iv 1.6 8v cylinder head torque settings

Hi the title says 1986 is the correct

Posted on Mar 06, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What is torque settings for head bolts on Kia pregio 2001


What are the cylinder head torque settings for a KIA K2700

www.answers.com > ... > Categories > Cars & Vehicles > Asian Cars > Kia
What is the torque specification for the cylinder head on a 2002 Kia Sportage? ... the correct torque for cylinder head bolt of kia pregio 2.7 diesel is 130-135ft-lbs. ... Thehead bolt torque settings, on your Kia 2.7 diesel engine, is 70 pounds per ...

Aug 17, 2015 | Kia Cars & Trucks

1 Answer

Torque settings on a fiat uno 1100 engine


Answer barbo(fiat mechanic) Fiat do not issue torque settings for a punto they use angles so that you can snap your stretch bolts! after contacting fiat and haynes neither of them would give proper torque settings, so i delved into my many tech manuals on fiat fire engines which is what is in your punto and i have successfully changed many fiat punto head gaskets using the following torque settings: stage 1 starting from the centre head bolts tighten to 33nm: stage 2:65nm and finally stage 3: 96nm these torque settings work fine and will probably save you buying new head bolts.

Oct 29, 2014 | Cars & Trucks

2 Answers

What is the cylinder head bolt torque settings fir a 4g69 mitsubishi engine ?


BOLT INSTALLATION


Apply engine oil to the thread of the bolts and to the washers.
Tighten the bolts to the specified torque, using the tightening sequence shown.
Tightening torque: 54 ft-lb +/- 2 ft-lb
Loosen all bolts fully in the reverse order of tightening.
Re-tighten the loosened bolts to the specified torque in the tightening sequence shown.
Tightening torque: 15 ft-lb +/- 1 ft-lb
This step is to make it easier to ensure you are making 90 degree turns. Make a paint mark across each bolt head and cylinder head.
Tighten the cylinder head bolts 90 degrees in the specified order.
Tighten the bolts another 90 degrees in the specified order and check that the paint marks on the cylinder head bolts are aligned with the paint marks on the cylinder head.
Link to the guide for this engine: http://www.mivec.co.nz/tech/4G9x_Engine_Manual.pdf



Aug 04, 2014 | 2007 Mitsubishi Outlander 2.4

1 Answer

What is the torque settings for a mitsubishi colt hiline 2.0i cylinder head?


There is no torque value. Commonly, Head bolts are tightened and then removed in sequence as you step threw 3 values: 23/33/45 ft lbs then the final value is achieved by rotating the bolts 90 degrees so the final value is unknown.

You have to get either a hayes manual or follow a procedure online if you are replacing the head gasket. If you are not replacing the gasket do not "re-torque" the head bolts thinking that you can fix a head gasket leak.

Jul 29, 2014 | 2005 Mitsubishi Colt 1.1

1 Answer

Hi. I am assembling a avanza 1.3 that blew head gasket. What are the torque settings for head bolt


I don't have the specs.Evenly go around to all of the head bolts and gradually torque them. 20,40 60 foot pounds.
Depending on the type of gasket you used,you may have to re-torque the bolts after it has gone through one heat cycle.

Mar 08, 2013 | 2007 Toyota Avanza 1.3

1 Answer

Need torque settings for cylinder head bolts on a 52 reg skoda fabia 1.4 16v any help much appreciated thanks


Torque settings for cylinder head bolts for Skoda Fabia 1.4 16v

Cylinder head bolts tightening order:

tdisline_116.jpg

IMPORTANT NOTE: RENEW BOLTS!

Stage 1: Tightening torque = 30 Nm
Stage 1: Tightening torque = 90 Degrees
Stage 1: Tightening torque = 90 Degrees

Please do rate my response. Thanks!

Dec 17, 2010 | Volkswagen Polo Cars & Trucks

3 Answers

I need torque settings for the engine ie head bolts v6 engine 1


i am replacing the heads on a GMC 350 cu in engine. what is the final torque of the head bolts?

Jul 15, 2010 | 1985 Chevrolet Camaro

2 Answers

Torque setting cylinder head bolt 4 cylinder KIA sportage


I need the torque settings and pattern for a Kia Sportage 2.2

Nov 24, 2009 | 2001 Kia Sportage

3 Answers

Torque settings for cylinder head nissan sentra


Tighten in sequence to 29ft.lbs then tighten in sequence to 58ft lbs. then loosen all bolts. Then tighten in sequence to 33ft lbs. then tighten each bolt in sequence 90 degrees then tighten each bolt again 90 degrees

Jul 18, 2009 | 1999 Nissan Sentra

4 Answers

Torque wrench settings


please understand there are a lot of items on a car that require torque settings every thing from the lug nuts to every engine bolt, and transbolt. please be more specific

Jul 03, 2008 | 1999 Ford Taurus

Not finding what you are looking for?
2004 Honda Odyssey Logo

645 people viewed this question

Ask a Question

Usually answered in minutes!

Top Honda Experts

yadayada
yadayada

Level 3 Expert

60769 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6811 Answers

Are you a Honda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...