Question about Hyundai Elantra

1 Answer

I installed a new mastercylender and cannot get a good pedal. Will not blead left front, I reused the perportioning valves. Bench bleed twice, have gravity bleed, any idea's?

Posted by on


1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 10 achievements.


    An expert that got 5 achievements.


    An expert whose answer got voted for 500 times.

  • Hyundai Master
  • 2,007 Answers

Loosen your bleeder screw. Push one end of a peice of vacuum line on it (about 2 feet long). Make sure it fits tight. Put the other end of the vacuum line in a clear bottle or jar of clutch/brake fluid, about half full. Pump the brake pedal until the bubbles quit coming out. Tighten the bleeder screw, remove the hose, and repeat on each wheel. You have to keep the jar end of the hose submerged. If not, when you release the pedal, it sucks the air back in. If you can't get any air out of that one screw, you may have to remove the screw and clean it, or replace it. Good luck.

Posted on Mar 20, 2011


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

2 Answers

Brakes not working right

you need to bleed your master cylinder also. you are going to need help pumping on the brakes. and you can bleed your brakes on the master cylinder lines just you bleed your brakes.

Jan 22, 2018 | 1997 Nissan 200SX

2 Answers

1992 f-250 brake pedel go's to the floor when applyed. I installed new master cylinder & brake booster new rear brakes all new front ok no leaks.

Did you remember to bench bleed the new master cylinder before installing it on the truck, to get all the air out of it?

Jan 26, 2011 | 1992 Ford F250

2 Answers

The brake pedal goes to the floor with no resistance. I have replaced both rear wheel cylinders and master cylinder, problem persists.

Is the brake-light on? I understand what you replaced but what was the procedure that you followed to bleed the brakes? Did you bench bleed the master? After installing the new master, did you bleed air out of the proportioning valve, and all four wheels. You need to start with the F/L wheel and finish with the R/R wheel. Unless you own and are using an automatic brake bleeding unit. You will have to get another person to help bleed them.

May 07, 2010 | 1984 Ford F 150

1 Answer

Brake pedal went to floor. replaced master cylinder and blead system but no luck. what do i do?

Did you bench bleed the master cylinder before installing? Run lines from outputs on master cylinder back into reservoir and pump air out . Connect lines and bleed system, Start from back passenger wheel first then back drivers wheel then front passenger and last front drivers wheel.

Feb 27, 2010 | 2005 GMC Sierra 1500 Hybrid

1 Answer

How do you bleed the abs unit on a 1997 chevrolet truck

start by bleeding the master cylinder bleed the line closest to the fire wall, then proceed to the right rear wheel, left rear wheel, right front wheel, and then the left front wheel.

Sep 16, 2009 | 1997 Chevrolet Malibu

3 Answers

Brakes were working fine and all the sudden the pedal went to the floor bench blead new master cylinder still no pedal any ideas

what kind of vehicle?? wheel cylinder maybe, ... look in side rim for fluid... does new master loose fluid?? did you bleed brakes after new master install???

Apr 07, 2009 | 1994 Toyota 4Runner

1 Answer

How to bleed brakes

Sounds like the proportioning valve is stuck. You may need to break a front bleeder loose and hit the pedal the unseat the valve. Then blead the rearbrakse and then bleed the wheel where you broke the bleeder loose. That should work.

Good Luck

Oct 12, 2008 | 1997 Chevrolet S-10 Pickup

1 Answer

Audi A3 diesel 2000 reg brake pedal going to the floor with engine running and heavy pedal pressure

you should have bench bleed the master cylinder first before installation return cylinder and get a new one than bench bleed it first than install it to car once installed you may have to bleed each wheel

Jul 06, 2008 | Audi A3 Cars & Trucks

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

94 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hyundai Experts


Level 3 Expert

79847 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8836 Answers

Are you a Hyundai Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides