Question about 1999 Ford Crown Victoria

1 Answer

Wire connection for a cooling fan on a 1999 crown victoria

I want to direct wire the fan, someone cut of the plug harness.

Posted by on


1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 2 Answers

Direct wiring of the fan is not a good idea. The fan will not cycle and it could burn the fan up. It would be best to get another harness from the auto parts store or from a salvage yard. The auto parts store should have a diagram to wire in the harness or you can see how the harness wires in by looking at another vehicle. If you are going to direct wire the system, be sure to put in an inline fuse on the hot wire.

Posted on Aug 09, 2008


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

I can start my 1999 crown Victoria with spark plug #1 disconnected but, if I connect it, it will shut off and will blow the fuse

A bad plug boot or coil is shorted bend the boot back and forth it will show a crack or even break if it's to brittle if not that coil or the wire or plug is dhorted out look at the wire for torn insulation making contact to ground if not coils bad and maybe cracked letting the positive voltage escape to ground and blowing the fuse try to check it in the dark while someone cranks the engine the voltage leak will be seen as a spark

Nov 19, 2016 | 1999 Ford Crown Victoria

1 Answer

Where is the cooling fan sensor located at on a

You'll find said sensor on the lower radiator tank. Just look for a wire connected to a sensor screwed into the lower tank and that's it.

Sep 24, 2014 | 2003 Ford Crown Victoria

1 Answer

My cooling fan stooped working ,my a/c stopped working and i checked all the fuses that are related to that circuit. 2006 crown victoria taxi package. all started off when you turn the key ,and the...

check your vlcm-variable load control module, located in front of the radiator (has fins, and has a large harness attached to it)-the harness may need to be tightened or the module itself may be bad-before to replace it swap relays for the AC with the ABS to see if it is just a bad relay.

Sep 12, 2011 | 2006 Ford Crown Victoria

1 Answer

Need help finding the ignition module on a 97 ford crown victoria

There is no ignition module. The ignition coils are controlled directly by the Powertrain control module (computer) located inside the vehicle above the drivers left foot and connected to the engine wiring harness thru the firewall

Apr 06, 2010 | 1997 Ford Crown Victoria

1 Answer

Battery not charging, new alternator, checked connections, checked fuses, alternator harness was melted at the end where it plugs into the main harness

A melted plug typically means a loose connection. Maybe one of the pins in the connector got loose and the poor connection created heat. If there are only a couple of wires to the plug and harness I would cut out the plugs and use good solderless connectors to repair. I wil be a lot less expensive than a new harness. If it is just damage to the plug going to the alt you can get replacements for them.

Oct 10, 2009 | 1990 Ford LTD Crown Victoria

1 Answer

Can't start my cron vic 1998 battery sign comes on and off but battery is good alternater is good

i have a 1999 Ford Crown Victoria Police Interceptor. you have a short in your wiring harness leading to your battery. this happens every time with these cars, good battery-good starter-good alternator but car still wont turn over because the power from the battery isnt able go directly to the motor. check your relay circuits and harness.

Jul 26, 2009 | 1998 Ford Crown Victoria

1 Answer

I am missing my number eight spark plug assembly and wiring harness. I need to know what parts are needed.

plug coil pack and harness repair plug. check plug hole for threads chances are the threads are gone out of plug hole if so you will need a repair kit also.

Jun 09, 2009 | 1999 Ford Crown Victoria

1 Answer

Radiator fan in my 2003 crown victoria runs continuosly

No, the fan is supposed to come on only at certain temperatures.

Trace the wiring from the fan back, there should be a temp switch/relay in line. If there isn't,then someone has bypassed it and wired the fan to run when the car is running.

Jan 02, 2009 | 1999 Ford Crown Victoria

2 Answers

P0304=misfire in cylinder 4. coil? spark plug? spark plug wiring. 1999 crown vic 4.6 V8. runs ok, just little cutting out every now and then.

not coil coil it wouldnt fire at all it is either a plug or a wire replace the wire and plugs and that will fix it

Oct 06, 2008 | 1996 Ford Crown Victoria

Not finding what you are looking for?
1999 Ford Crown Victoria Logo

334 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts


Level 3 Expert

77499 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22306 Answers


Level 3 Expert

5622 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides