Question about 1990 Ford F250

1 Answer

1990 ford f250

4 hose connector in the back but on the top of the engine

Posted by on

  • Curt Downs May 11, 2010

    What engine is in the F-250, and what exactly is your question concerning this 4 hose connector? Countrycurt0

×

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 508 Answers

I believe the connector you are inquiring about is where your vacuum connections come into play. If you have power brakes this is where the larger line hooks up from your power brake booster. The others will be specific to your engine configuration. Any leaky lines will adversely affect your vehicles performance and idle characteristics.

Posted on Feb 14, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where is thermostat on 1990 econoline ford van


Follow the top rad hose back to the metal housing isa attached to, the thermostat will be inside the housing.

Feb 19, 2015 | 1990 Ford Econoline

1 Answer

Need to replace engine thermostat on 1990 festiva


follow the top radiator hose fron radiator to engine, there at end of the hose is the thermostat housing. remove hose from engine side, also remove the 2 bolts from housing to reveal the thermostat. remember which way the thermostats positioned in the housing. replace with your new one and also new gasket. reinstall your hose and you should be good to go.be prepared to lose some fluid when you remove the top radiator hose. i've always found that a little rtv glue'''blue glue''' will hold the gasket in place while you're replacing you thermostat. hope this helps!!

Aug 20, 2010 | 1990 Ford Festiva

1 Answer

1990 F350: i just bought a 6.9 ford and i found a small hose ...


try disconnecting that hose and crank the engine

May 16, 2010 | 1990 Ford F350

1 Answer

What controls the temperature gauge on a 1990 ford f150 5.0 engine and where is it located


The temp gauge on the dash displays the information transmitted by the coolant temperature sensor. This sensor is located - on the engine - by the water neck. The water neck is where the top radiator hose comes across and connects to the radiator. This sensor can look like the one here:

http://fordfuelinjection.com/?p=28

Hope this helps.

Mar 18, 2010 | 1990 Ford F150

1 Answer

ERG valve Replacement How would you go about getting to this valve....


in my 1990 ford f-250 it sits on top of the engine has small hose and wiring on it near the front of engine..I hope this is of some help

Dec 21, 2009 | 1998 Ford Explorer

2 Answers

Iiiiiiihow to install thermostat for 1990 honda civic


Thermostat is located where the lower hose connects to the motor. Not the upper. Just follow the lower hose back to the engine, remove spring clamp, three 10 mil. nuts, and housing, therm has no gasket but o-ring seal instead.

Sep 17, 2009 | 1990 Honda Civic

1 Answer

Replace thermostat on Ford e350 diesel 1990


follow top hose from radiator to engine, it connects to steel tube with a plat and 2-3 boltshold plate down. sypgon radiator down into clean bucket, remove bolts, take out thermostat, clean both mounting surfaces very clean until only metal showing put in new thermo put gasket on tighten bolts and add antifreeze

Jul 06, 2009 | Ford E-350 Cars & Trucks

1 Answer

Making a soundlike a hole i n muffler


Depending on what engine is in your truck, I think that canister does not have a hose connected to it. A common source of that exhaust leak noise is from a broken thermactor check valve in the back of the engine. If it is a Ford V8 look in the back of the engine closest to the firewall. There is a Metal pipe that is bolted to the back of the left & right cylinder head. in the middle of the pipe is a bulblike checkvalve that has a 1" hose that suppose to be connected to the check valve... if the hose is not connected look to see if the top of the check valve has rotted off and the broken piece is still clamped in the inside of the hose. The easiest way to replace the valve if it is broken is to unbolt the tube forn the left & right side of the rear of the cylinder heads and fish the tube out and clamp the tube on a bench vise. Do not distort the tube or you will struggle to bolt it back on.

Apr 04, 2009 | 1990 Ford F150

Not finding what you are looking for?
1990 Ford F250 Logo

Related Topics:

160 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

70347 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22041 Answers

Ron Lankford

Level 3 Expert

5386 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...