Question about 2001 Ford Ranger Regular Cab

Open Question

Need torque specs for 2001 ranger front suspension , and tie rod nut etc.

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

reisdos
  • 1297 Answers

SOURCE: need the torque specs for

hope this helps...

4c17033.jpg

2c46aed.jpg

Posted on May 11, 2010

  • 1 Answer

SOURCE: Torque specs for front wheel hub nut

112 to 174 ft lbs

Posted on Apr 04, 2009

warlock61
  • 659 Answers

SOURCE: Axle nut torque spec

184 ft/lb

Posted on May 11, 2009

tneubauer
  • 437 Answers

SOURCE: I need a suspension diagram that shows the Inner tie rods.

The inner tie rods are screwed into ends of the steering rack assembly.

Look at this diagram. #6 is the rubber boots and #7 is the shaft from the inner tie rods.


http://www.anubiscycle.com/fixya/2000-windstar-steering-gear.jpg

Posted on Jun 08, 2009

wilsodfarm
  • 986 Answers

SOURCE: torque specs. for outer tie rod ends for 2006

Tie rod end is 35 ft. lbs. Pinch bolt for the lower ball joint - 105 .I hope this helps you

Posted on Oct 06, 2009

Testimonial: "thanks for the help"

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What are the torque specs on a 2007 Jeep Compass. Front axel nut and tie rod end?


Axle nut=180 foot pounds Outer tie rod nut= 97 foot pounds

Nov 15, 2015 | Jeep Cars & Trucks

1 Answer

Looking for front suspension torque specs for tie rod. Or is a stabilizer shaft link the same thing as a tie rod


The tie rod connects the two front steering pieces together so that both tires point in the same direction at the same time.
The stabilizer shaft link is part of the suspension that helps keep the vehicle lever when you're going around corners.
Check with your local GM dealer or auto parts supply for torque specs.

Mar 16, 2015 | 2006 Chevrolet Silverado 1500 2WD

1 Answer

What's the outer tie rod end torque specs for 2000 Dodge Dakota sport ?


this was copied off of the following link. should be same torque requirments-
this is off a 2004 manual,which should be real close if not exact

INSTALLATION
1. Align reference marks and install pitman arm.
2. Install the lock washer and retaining nut on the pitman
shaft and tighten nut to 251 N·m (185 ft. lbs.).
3. Install the drag link (1) to the pitman arm (5). Install
the nut (4) and tighten to 54 N·m (40 ft. lbs.) Then
an additional 90°.
4. Remove the supports and lower the vehicle to the
surface. Center steering wheel> and adjust toe,
(Refer to 2 - SUSPENSION/WHEEL ALIGNMENT -
STANDARD PROCEDURE).
5. After adjustment tighten tie rod adjustment sleeve
clamp> bolts to 61 N·m (45 ft. lbs.).
NOTE: Position the clamp on the sleeve so retaining
bolt is located on the bottom side of the
sleeve

got it from here -

Tie rod end torque spec DodgeTalk Dodge Car Forums Dodge Truck Forums and...

Feb 23, 2015 | Dodge Cars & Trucks

1 Answer

Torque specs for 2008 ford ranger 4x2 front axle


Torque Specifications

Description Nm lb-ft Axle-to-frame bolt 66 49 Axle damper-to-frame bolt 34 25 Brake caliper guide pin bolt 33 24 Differential bearing cap bolt 61 45 Differential housing cover bolt 29 21 Ring gear bolt 122 90 Tie-rod nut 91 67 U-joint spider retainer bolt 19 14 Upper ball joint pinch bolt 48 35

Sep 18, 2014 | 2008 Ford Ranger 2WD

1 Answer

What is the torque specs for a tie rod end on a 1994 toyota camry


The tie rod end adjusting nut, 54 ft lb or 74 Nm
The tie rod end ball joint nut, 36 ft lb or 49 Nm

May 10, 2014 | 1994 Toyota Camry

1 Answer

What is the torque spec on the cv shaft drivers side 1997 toyota carolla


LOWER SUSPENSION ARM TO STEERING KNUCKLE NUTS AND BOLTS TORQUE 105 FT LBS. TIE ROD ENDS TO THE STEERING KNUCKLE NUT FT LBS.

May 16, 2011 | Toyota Corolla Cars & Trucks

2 Answers

I want to know how to fix the alignment on my 1995 honda accord ex.


Before making wheel alignment adjustment, perform the following checks:
  1. Tires should be equal in size and runout must not be excessive. Tires and wheels should be in balance, and inflated to manufacturer's specifications.

  2. Wheel bearings must be properly adjusted. Steering linkage and suspension must not have excessive looseness. Check for wear in tie rod ends and ball joints.
  3. Steering gear box must not have excessive play. Check and adjust to manufacturer's specifications.
  4. Vehicle must be at curb height with full fuel load and spare tire in vehicle. No extra load should be on vehicle.
  5. Vehicle must be level with floor and with suspension settled. Jounce front and rear of vehicle several times and allow it to settle to normal curb height.
  6. If steering wheel is not centered with front wheels in straight-ahead position, correct by shortening one tie rod adjusting sleeve and lengthening opposite sleeve equal amounts.
  7. Ensure wheel lug nuts are tightened to torque specifications
Ride Height Adjustment

Before adjusting alignment, check riding height. Riding height must be checked with vehicle on level floor and tires properly inflated. Passenger and luggage compartments must be unloaded. Bounce vehicle several times, and allow suspension to settle. Visually inspect vehicle from front to rear and from side to side for signs of abnormal height.
Measure riding height. See figure. Riding height between left and right sides of vehicle should vary less than 1′ (25.4 mm). If riding height is not within specification, check suspension components and repair or replace them as necessary.
Wheel Alignment Procedures

Honda recommends using commercially available computerized 4-wheel alignment equipment. Follow equipment manufacturer instructions to obtain vehicle alignment settings. Use following procedures for necessary adjustments.
Civic Camber Adjustment
Compare camber settings with vehicle manufacturer recommendations. If camber is incorrect, check for bent or damaged front suspension components. Replace faulty components. Recheck camber.
Civic Caster Adjustment
DO NOT use more than 2 shims. If more than 2 shims are required to adjust caster angle, check for bent or damaged suspension components.
Compare caster settings with vehicle manufacturer recommendations. If caster is incorrect, check for bent or damaged front suspension components. Replace faulty components. Recheck caster.
Civic Toe-In Adjustment

  1. Secure steering wheel in straight-ahead position. Measure front wheel toe-in. If adjustment is needed, loosen tie rod lock nuts. Turn both tie rods equally in the same direction until front wheels are in straight-ahead position and toe-in reading is correct. Tighten tie rod lock nuts. Reposition tie rod boots if twisted.
  2. Ensure parking brake is released. Check rear wheel toe-in. If adjustment is needed, hold adjusting bolt on rear compensator arm and loosen lock nut. See figure. Adjust rear toe-in by sliding rear control arm until rear toe-in is correct. Install NEW lock nut, and tighten it while holding adjusting bolt.
Wheel Alignment Specifications

  • Camber - Measurement in degrees.
    • Front: 0 (range -1 to 1)
    • Rear: 0.33 (range -1.33 to 0.67)
  • Caster - Measurement in degrees.
    • 1.17 (range 0.17 to 2.17)
  • Toe-In - Measurement in inches (mm).
    • Front: -0 (0)
    • Rear: 0.08 (2.0)
  • Toe-In - Measurement in degrees.
    • Front: 0.00 (range - 0.16 to 0.16)
  • Toe-Out On Turns - Measurement in degrees.
    • Inner: 41.00
    • Outer: 33.50
Torque Specifications Ft. Lbs (N.m)

  • Rear Control Arm Adjusting Bolt: 48 (65)
  • Spindle Nut: 136 (185)
  • Tie Rod Lock Nut: 41 (55)
  • Wheel Lug Nuts: 80 (108)
hope this helps you out.

May 09, 2011 | 1995 Honda Accord

1 Answer

2006 grand caravan sxt 3.8 liter outer tie rod torque specs needed please.


Hello billmarks: My name is Roger and I will help you. The torque specs for the tie rod lock nut and the tie rod spindle nut is 55 foot pounds. Should you need further help please just ask.Please rate the answer. Thank You for using Fix Ya. Roger

Sep 08, 2010 | 2006 Dodge Grand Caravan

1 Answer

Torque spec for king nut on front spindle of 1999 2 wheel drive dodge dakota?


Unsure as to what you are calling the King nut but here are the torque specs for your front end.

Steering Gear-To-Cradle Bolt...........135 ft pnds
Steering Gear-To-Crossmember Bolt (Dakota 2 WD)..........190 ft pnds
Suspension Cradle Plate To-Cradle Attaching Bolt..............123 ft pnds
Tie Rod End-To-Steering Knuckle Nut Dakota (2WD) .............65 ft pnds
Tie Rod Lock Nut.....................55 ft pnds

Dec 08, 2009 | 1999 Dodge Dakota

1 Answer

Need torque spec for 2000 Cirrus outer tie rod ends


45 Ft-lbs Tie-rod balljoint stud-to-steering knuckle nut, and 55 Ft-lbs Tie-rod (outer)- to- inner jam lock nut

Apr 04, 2009 | 2000 Chrysler Cirrus

Not finding what you are looking for?
2001 Ford Ranger Regular Cab Logo

Related Topics:

820 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

fordexpert

Level 3 Expert

5501 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...