Question about Mazda B2600

Open Question

Got a 88 mazda b2600 trying to get the cv axle out of the front diff

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 373 Answers

SOURCE: front axle how to remove half shaft

Hi.. The step to remove the front Axles of you Vitara.
Raise and support Vehicle . Remove front wheel,
Drain Diff,fluid,
Remove Locking Hub if is equipaded,
Remove Circle clip from axle shaft
On right side of Vehicle, Remove the Stabilizer Little ball joint nut. Remove castle nut Front Tie rod end,
Remove mounting bolts from brake calipper,
Remove Calipper from steering knuckle and wire a side.
Remove Stud Nut from steering knuckle,
Support Lower suspension arm with a jack,
Remove lower strut bracket bolt ,
Lower jack and disconnect Knuckle from lower suspension crontrol arm,
Pull Outler joint from Hub.
Use Large screwdriver or Prybar To pry Right inner joint from differential, The axle will go out making a little froce with the prybar,
To remove the left side,
Remove mounting bolt from inner joint flange,
Pull out axle from hub.

To reinstall just reverse the prosses.

I hope this help on your job...
Thank you for use fixya....


Posted on Aug 19, 2008

BigBlue77
  • 59 Answers

SOURCE: 2005 Yukon Front Diff Axle seals

You don't have to remove the whole diff to change the seals, but you will have to seperate it where the shaft meets the carrier housing. There is a clip holding the passenger axle shaft in place that you have to remove to change the seal. The drivers side axle stub can be removed with a little force as there is a spring clip holding that side in.

Posted on Sep 06, 2008

  • 14 Answers

SOURCE: 94 Geo Prizm CV or driveaxle?

on this type of vehichle, you have two axles in the front; one going to each side. Chances are that the boot at the axle joint was torn and that is why you are having problem. In teh past people used to replace the boot, this day and age its actually cheaper to replace the axle. So you would need to replace that side of the axle (the half shaft).

Posted on Nov 20, 2008

  • 4 Answers

SOURCE: front cv axle 1995 dodge intrepid

Naturally you need to remove the tire then the brake caliper. After the brake caliper is removed then you need to remove the 34mm axle nut that is inside the hub. After that is removed then you can remove the hub. Becareful not to damage the hub seal on the back or you will have to buy a new hub (100 or more). Then you need to remove the strut knuckle assembly. Once the knuckle assembly is removed then you can pull the CV axle. Take care the inner CV housing is held in place by an inner snap ring. You will probably have to pry off the inner housing. Once the axle is off then install the new axle (if you buy complete axle). Make sure if you are doing both that you take care which side you are installing. I made that mistake and double the work. Slide the new axle on the spline and make sure it is seated completely. Then put back together the reverse of removal.

Posted on Mar 24, 2009

germcelchar
  • 389 Answers

SOURCE: how do i remove cv axle for a 98 isuzu trooper

Go to my profile I have just explained how to change a cv boot on a Trooper. The axle needs to be taken out to change the boot so the same solution. What you call an axle I have refered to as a drive (short for driveshaft) It takes a lot of explaining so save me a lot of writing if you read the solution I gave for changing the CV boot. Cheer's

Posted on Sep 28, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Front diff


Here might be the answer for that.
Cv Axle Answers com

May 15, 2014 | Kia Sorento Cars & Trucks

1 Answer

Can you remove the driver side cv axle from a 2005 Chevy asteo van AWD permenanlry


The CV axle stub (end with the axle nut on it) supports the wheel bearing, removing the axle then driving on it would cause the bearing to wear prematurely. I would not recommend this. The front differential is also sealed by the cv assembly, removing it would cause the diff fluid to leak out . CV shafts for this van run $50-80. I would replace if it is bad, instead.

May 04, 2014 | 2002 Chevrolet Astro

1 Answer

How do i remove the front drive shafts on a 97 mazda b2600 4wd to replace the cv boots?


When you did the ball joints you should have pulled the axles

I would guess that you know the axle nut has to come off & that
in most cases you break the bottom ball joint loose, so you can
get the axle out of the steering knuckle

So I will guess you can't get the axle out of the trans

You use a long pry par,3 foot or more & put the end against
a piece of wood, so as not to pry on the aluminum trans case

Then you pop it out with the pry bar.
You don't pry on the axle ,you use the side of the pry bar
to bang it with the end against the wood

Sep 26, 2012 | 1986 Mazda 323

1 Answer

I got a 1997 gmc jimmy 4wd my 4wd doesnt engage the front diff but it engages the ****** for low range ive checked my actuator pump and its moving but now i have a rattling noise in my front drivers side...


It would appear you have a failed CV shaft on your drivers side front. If the axle is jumping around, that means the 4wd is engaged, but the front wheels can't pull because the one axle is just freewheeling. Replace that left axle and you should be good to go. Might want to check the cv boots on the right side axle while you are there.

Aug 22, 2011 | GMC Jimmy Cars & Trucks

1 Answer

How to remove both front cv axles from front diff, i have every thng off and this aint my first rodeo, so whats up with getting the inner cv joint out of the diff.


If you have everything loose so the CV axle will pull out of the diff, try this: Using two flat head screwdrivers, put them beteween the inner edge of the joint and the diff. GENTLY pry with both screwdrivers 180 degrees apart ( like at 3 and 9 o'clock). there is a clip in a groove that has to retract al the way in to release the halfshaft. It can be very frustratiing as I have been there done that. try rotating the axle about a quarter turn and then use the two screwdrivers again. some times you just have to find the "sweet spot".

Jul 24, 2011 | 1998 Isuzu Trooper

1 Answer

Im replacin the cv joints on passanger side and driver side how do i get the axle out of the transmission casing is ther a key behind the plate with the 4 bolts? my truck is a 99 isuzu rodeo LS 4wd


remove inner cv boot, just on inside edge is circlip which holds inner bearing joint into outer housing remove circlip and separate joint outer housing does not come out of front diff unless you drop or remove whole front diff assembly
will have to remove whole stub axle hub assembly to remove drive shaft from outer wheel stub axle (hub) assembly

Apr 20, 2011 | 1999 Isuzu Rodeo

2 Answers

Front pass side cv axle removal on 2003 hyundai santa fe


pull swiftly !!! on the axle hub
as its got a big circlip in there & that is why it feels STUCK!
Cheers Rob

Aug 15, 2009 | 2004 Hyundai Santa Fe

3 Answers

My front differential is leaking!


I cannot see it, but I am guessing that you need to replace your axle seal. To do this,you have to pull your CV shaft out. Remove the tire, remove the caliper from the top of the rotor. Using a hammer on the back, remove the rotor. Take off the spindle (axle) nut, separate the axle (CV shaft) from the hub. Replace seal. It should pop right out. Good luck!

Aug 05, 2009 | GMC Sierra 1500 Cars & Trucks

1 Answer

How to replace front cv shafts ?


remove inner cv boot, just on inside edge is circlip which holds inner bearing joint into outer housing remove circlip and separate joint outer housing does not come out of front diff unless you drop or remove whole front diff assembly
will have to remove whole stub axle hub assembly to remove drive shaft from outer wheel stub axle (hub) assembly

Aug 01, 2009 | 1997 Isuzu Rodeo

2 Answers

When turning hear a clicking noise from drivers front wheel 1999 mazda millena s


most likely the cv boot is bad will need to be replaced recomend change the whole cv axle

Jul 29, 2008 | 2000 Mazda Millenia

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

57 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mazda Experts

yadayada
yadayada

Level 3 Expert

75797 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8140 Answers

Are you a Mazda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...