Question about 2008 Pontiac G6

1 Answer

Hi I used a sequence to shut off my power door locks but want to reactavate them again pontiac g6/06,also sometirs when i shift it goes hard into gear with a clunk and small ****

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Pontiac Master
  • 14,036 Answers

IF PRESSING REMOTE TRANSMITTER LOCK BUTTON ONCE TO LOCK ALL DOORS DONT WORK.THE REMOTE HAS TO BE REPROGRAMMED AT DEALERSHIP.CLUNK NOISE GOING IN GEAR COULD BE LOOSE FRONT SUSPENSION COMPONENTS OR DAMAGED LOOSE ENGINE MOUNT OR TRANSMISSION MOUNT.CLUNK NOISE CAN COME FROM LOOSE DRIVE CHAIN ON TRANSMISSION DRIVE CHAIN SPROCKETS

Posted on Mar 20, 2011

  • Brother Kinnon
    Brother Kinnon Mar 21, 2011

    I turned off the locks by turning key on and off and then on and pulling in on signal light switch there must be some sequence to reverse this also the tranny doesn't hard shift all the time just seems when tranny is warm

  • Jonah Oneal Mar 21, 2011

    THE DEALERSHIP HAVE REPROGRAM KEY REMOTE.LET DEALERSHIP DO A SERVICE CHECK AND THEY WILL CHECK THE TRANSMISSION. FLUID AND FILTER.

×

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Key doesn't go into door lock


open the other door to get in.
spray some WD-40 to loosen lock.
if key won't go in there might be something jammed in lock.
I might try a tiny drill to see what is in there.
drill size of .0040 or smaller.

Jan 31, 2013 | 2007 Pontiac Grand Prix GXP Sedan

1 Answer

2005 Chevrolet Tahoe Power Windows and Power Locks not working.


The power windows an power locks are controlled by a module , DDM - driver door module . As far as the locks locking when you put the vehicle into reverse an unlocking when you put the vehicle into park , that's how there are suppose to work , automatic lock an unlock feature . When you put the vehicle into any gear from park the locks should lock . Did she hit window lockout function ?

The power door lock system consists of the following components:
• The driver door module (DDM)
• The passenger door module (PDM)
• The body control module (BCM)
• The driver information center (DIC)
• The rear door lock switch
• The door lock relay
• The door unlock relay
• The liftgate lock relay--utility vehicles with liftgate only
• The reversible door lock actuators in each of the doors and liftgate
• LOCKS 20A fuse (rear lock/unlock relay supply voltage)
• ECC 10A fuse (liftgate lock relay supply voltage .

Programmable Automatic Door Locks
The automatic door lock feature can be programmed to control the door lock system. The automatic door lock feature is factory programmed to have all doors lock and unlock. For detailed instructions on programming the automatic door locks, refer to Vehicle Personalization in Personalization.
When the automatic door lock feature is programmed to control the door lock system, the driver door module (DDM), passenger door module (PDM) and body control module (BCM) will lock the vehicle doors if the following inputs are true:
• Ignition 1 input is active.
• All door jamb switch inputs are inactive.
• Cargo door or liftgate/liftglass ajar inputs are inactive.
• Transmission is shifted out of park.
This automatic door lock function will only occur once per ignition cycle unless, a door jamb switch input changes state to active and back to inactive. Then the DDM, PDM and BCM will lock all doors again.
Once the automatic door lock feature has locked the doors, the BCM will then unlock all the doors when the transmission is shifted into park.
Driver, Passenger and Cargo Door Lock System Operation
The front power door lock switches are integral components of the driver door module (DDM) and passenger door module (PDM). The switches are two position normally open rocker switches. When placed in either the lock or unlock positions, the switches provide a direct input to the DDM or PDM. The DDM or PDM monitors these inputs and sends a Class 2 message indicating a change in the switch's respective position. Modules which activate the power door lock motors receive the Class 2 message and activate the motor in the appropriate direction to lock or unlock the vehicle's doors and liftgate. The rear door lock switch provides a lock and unlock signal to the body control module (BCM). The BCM upon receipt of a lock or unlock signal will control the rear door lock relays and also send a Class 2 message to the DDM and PDM to perform the appropriate function.
The modules which activate the power lock motors are:
• The DDM (driver door lock actuator).
• The PDM (passenger front door lock actuator).
• The BCM (both rear door lock actuators and cargo door/liftgate).
The DDM and PDM are directly connected to the respective door lock actuator through the door lock motor lock and unlock circuits. Once a door lock or unlock request has been received, the module will supply battery voltage to one side of the actuator and ground the other causing the doors to lock or unlock.
The rear passenger and cargo doors differ slightly in that they use lock and unlock relays. The relays supply and coil sides receive a constant voltage through the battery voltage supply circuit. The normally closed contacts are connected to ground and the control side is connected to the BCM. Once a door lock or unlock request has been received by the BCM, the BCM will ground the control side of the appropriate relay. This energizes the relay and allows voltage to be applied to either the door lock motor lock or unlock circuits. since the other side of the door lock actuator is connected to the normally closed contacts of the opposing relay to ground, the doors lock or unlock.

Mar 16, 2017 | 2005 Chevrolet Tahoe

1 Answer

Programming 2006 pontiac pursuit fob


Gm and Chevy fob can be programmed at home. I have done it my self for a 01 chevy a 03 sunfire.
The steps on
 Step 1 of 5
Get in your Pontiac G6 and make sure all the doors and the trunk are closed.

 Step 2 of 5
Put your key in the ignition and hold the "Lock" button on the driver's car door.

 Step 3 of 5
Turn the G6 key in your ignition from "On" to "Off" while holding the "Lock" button, and do two more cycles of "On" and "Off" in quick succession.

 Step 4 of 5
Release the "Lock" switch on your door and press and hold the "Lock" button on your keyless remote for 10 to 15 seconds.

 Step 5 of 5
Remove the key from the ignition of your G6, and test the programming.

Or

Or

 Step 1 of 9
Enter your vehicle and close all of the doors behind you besides the driver's door. Be sure to have your keyless remote and ignition key in hand.

 Step 2 of 9
Insert and remove the key from the ignition twice in a row and then close and open the door twice in a row.

 Step 3 of 9
Insert and remove the key from the ignition again and close and open the driver's door two more times.

 Step 4 of 9
Insert the key into the ignition and close the driver's door.

 Step 5 of 9
Cycle the key in the ignition "On" and then "Off" and then remove the key from the ignition.

 Step 6 of 9
Wait for the locks to cycle to indicate the beginning of the programming sequence.

 Step 7 of 9
Press and hold the unlock and lock buttons on your remote for two seconds and then release.

 Step 8 of 9
Press and hold just the
lock button on the remote for three seconds and wait for the locks to cycle to indicate successful programming.

 Step 9 of 9
Repeat steps seven and eight to program any additional remotes and open the driver's door to end the programming sequence once you are finished.
Hope this helps

Feb 04, 2012 | Cars & Trucks

1 Answer

No power to left side rear window to raise the window. Window can only open (lower) by its own door control. The drivers door controls will not control that window at all. Checked with a fluke 87...


Then you found it also the window lock switch can also affect it use this diagram to help you you have a control switch on the driver side problem cansmo_133.gif

Aug 28, 2011 | 2005 Pontiac Grand Prix

1 Answer

99 Grand Am GT - power locks don't lock


easy one... many cars have the option of programing the lock sequence. Your manual (if you own one) shows you how to reset or program door locks. Someone may have press and held the lock switch in one direction for a short while which will put it program mode. If you dont have the manual you can try to hold the lock button torward lock for about 5-10 sec. You should hear a tone, then try pressing the switch again to reset.

Aug 21, 2009 | 1994 Pontiac Grand Am

1 Answer

My 2002 town & Country Rear sliding door wont close


You need to change the locking mechanism on the door,not the theft lock that you push down by the window,the lock that keeps thew door shut.I dont know why it wouldnt lock,it must be a factory defect,that worn out before its time..

Jul 29, 2009 | 2006 Pontiac Montana SV6

1 Answer

"Door Ajar" signal on dash panel stays on even when doors are clo


there should be a switch mounted( or more than one) in the door jamb that tells the car when the car door is open...i will probably look like a little plastic plunger...might be broken off or bad internally

Feb 22, 2009 | 2008 Pontiac G6 Sedan

1 Answer

The battery in my 2006 pontiac vibe went dead. I recharged it; however, the setting for the door locks changed. It now unlocks automatically when I turn the car off instead of when I put the car in park. I...


The 2006 Vibe no longer has that feature. It was discontinued after 2005. I have the 2005 so I know how to change it. If your 2006 is able to change then here are the directions from my 2005.
Programmable Automatic
Door Locks
If you have an automatic transaxle, your vehicle is equipped with an auto door lock/unlock feature which enables you to program your power door locks.
Your vehicle left the factory programmed to Mode 4.
The following is a list of the available programming options:
Mode 1: All doors and liftgate lock when the shift lever is moved out of PARK (P) with the ignition on and all doors and liftgate closed. There is no automatic door unlocking.
Mode 2: No automatic door locking or unlocking.
Mode 3: All doors and liftgate lock when the shift lever is moved out of PARK (P) with the ignition on and all doors and liftgate closed. All doors and liftgate unlock when the shift lever is moved to PARK (P) with the ignition on.
Mode 4: All doors and liftgate lock when the shift lever is moved out of PARK (P) with the ignition on and all doors and liftgate closed. All doors and liftgate unlock when the ignition switch is turned from ON to ACC or to LOCK.
To change the mode you are in, do the following:
1. Set the interior lamp control dial to the door position.
See Interior Lamps Control on page 3-16.
2. Move the shift lever into PARK (P) and close all doors and liftgate.
3. Turn the ignition to ON.
4. Within five seconds after the ignition is turned to ON, press and hold the power door lock switch in
the lock position for about five seconds.
5. The interior lamp will flash to indicate that the mode has been changed. For example, if the lamp flashes once, the function has been changed to Mode 1.
If the battery is disconnected or run down, the mode is changed to the initial mode which is Mode 4.

Jan 22, 2009 | 2006 Pontiac Vibe

1 Answer

2005 pontiac G6 GT, car shows engine locked


that is a theft system problem must take to dealer have them scan and program if ness.

Jan 04, 2009 | 2005 Pontiac G6

1 Answer

Automatic door locks


have you checked the fuse

Nov 07, 2008 | 1997 Pontiac Bonneville

Not finding what you are looking for?
2008 Pontiac G6 Logo

478 people viewed this question

Ask a Question

Usually answered in minutes!

Top Pontiac Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8210 Answers

Are you a Pontiac Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...