Question about Chevrolet Lumina

1 Answer

I need pic of sparkplug wire routing from coils 2 plugs

Posted by on


1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 20 achievements.


    An expert that got 10 achievements.


    An expert that got 5 achievements.

  • Chevrolet Master
  • 17,970 Answers

Send us the year, model and cyl numbers or check in this link: Engine_Firing_Orders.

Hope helps (remember to rate this answer)

Posted on Mar 20, 2011


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

No spark on #2cylinder

Year make and model? coil pack or coil on plug? If you have coil packs and just #2 replace the coil pack/s If you have coil on plug, Then you need to check the wiring. One wire will be hot(B+) with the key on. The other will go on and off to ground when cranking the engine. This is assuming you also check the plug wire/boot and made sure it isn't shorting out to the engine.

Dec 09, 2014 | Cars & Trucks

1 Answer

How do I get to the spark plugs on a 2004 vw passat 1.8t engine

This all depends on if its got coil over plug or sparkplug wires, whichever remove the coil or the sparkplug wire and then remove the sparkplug, this engine may have covers that cover the plugs, just remove the covers and make sure to label any wires you remove to get the covvers off.

Feb 02, 2011 | 2004 Volkswagen Passat

1 Answer

Need a diagram of spark plug wire routing, may have crossed wires, 95 3.8

This should solve your problem. Firing order 1s 1-4-2-5-3-6. Just connect the tower numbers on the coilpack to the sparkplugs of the cylinders as numbered in the diagram :


Dec 30, 2010 | 1995 Ford Windstar

1 Answer

Changing sparkplugs and wires

Change the plugs and wires one at a time as to not get confused. Purchase a quality set of custom plug wires that will fit perfectly. Put anti-sieze on the plug threads. Put some dielectric grease on the plug connector before snapping the plug wire in place. Route the plug wires exactly as they were originally routed.

Aug 11, 2010 | 2006 Kia Optima

1 Answer

I'm not sure which sparkplug and coil wires go

OK most stock engines for daily street driving use the NGK BUR6 and BUR8 spark plugs the 6's go in the Leading side so the bottom 2 spark plug holes. The 8's go in the Trailing side which is the top 2 spark plug holes.

Now as far as the plug wires. You have 2 coil packs one will have markings by the output tips that say L1 and L2 the other will say T1 and T2. its very simple L= Leading side, or bottom plug. T=Trailing side or top plug. 1=Front rotor, 2=Rear rotor.

Hook up everything that way and you should have no more issues.

Jul 31, 2010 | 1987 Mazda RX-7

1 Answer


Starting on the pasenger side. Remove the intake tube running from the air filter box to the throttle body and disconnect enough tubes to swing it out of the way. The sparkplugs are down below the small coils you see at the end of the sparkplug wires. With a 10mm socket remove bolt holding the coil, disconnect the plug at the top of the coil by squeezing it at the top and pulling straight off the coils.

Pull the coil straight up. there will be about a 6 inch tube that connects to the top of the spark plug when inserted. You will need a 5/8 sparkplug socket and about 2 feet of extensions to make it easy on yourself. Insert the spark plug socket and extensions down the hole you removed the coils with the tube from and remove and replace the sparkplug. Reinstall your coil onto the engine and move to the next one until you have replaced all the plugs on the passenger side.

Make sure you reconnect all the plugs to the coils, hoses to the intake tube and reinstall your intake tube. The drivers side is a little easier. Pop the spark plug wires from their plastic holders to free enough slack to be able to pull your sparkplug wires out of the block. For the plug closest to the front of the engine you will need to remove the 10mm bolt holding the ground wires to the intake manifold to be able to free enough space for removing the plug.

For the middle plug you will need to remove the 10mm bolt holding the bracket that is holding one of the throttle cables at the top of the intake manifold. For the rear plug just pop the flexible hose that runs behind the black metal bracket straight up out of its clip and push it out of the way along with any other hoses that run through this area. Pull the spark plug wire from its place by pulling straight up just like with the coils. there will also be about a 6 inch tube running down to the spark plug at the bottom of these plugs.

Remove and replace the plugs same as before. make sure you reconnect all your hoses and wires to their previous locations. Doublecheck to make sure you reconnect all the ground wires/ brackets. Also you will need to use " twin ground electrode plugs" (see sticker on front of your plastic timing belt cover? to the right of the radiator hose).

May 27, 2010 | 2002 Toyota Tacoma

1 Answer

Have a 2.2 4 cylinder distributorless chevy egine , acts like it might be out of time .Is there any way to check it ?

They dont really go out of time...These were common for bad sparkplug wires and ignition coils having open circuts...check for spark on plugwires 1 and 4 and 2 and 3 if there is no spark on 1 and 4 replace ignition coil the same with 2,3 the coils do fire the 2 sparkplugs simultainously ..and if there is an open circut in the plug wire only one wire will not have spark..if its a coil 2 wires will have no spark..

Apr 05, 2010 | Chevrolet Cavalier Cars & Trucks

1 Answer

Tune up on a 2008 dodge caliber 2.0. the wires are wierd and it dosent even look like they can be replaced

Doesn't have sparkplug wires, individual coils 1 per cylinder mounted right on top of the sparkplug. Here's a pic, they should look like #3.


Nov 23, 2009 | 2008 Dodge Caliber

2 Answers

2001 elantra, check engine light comes on and I get a cylinder 2 misfire

Inspect #2 spark plug and the ignition wire to it. Inspect the connector to the plug and to the coil... replace as needed.

Nov 02, 2009 | 2000 Hyundai Elantra

1 Answer

2003 Lincoln Aviator how to change spark plugs

Here is a pic of what it looks like
Remove the cover in the center of valve covers.
Remove coil packs
Remove spark plugs

Mar 23, 2009 | 2004 Lincoln Aviator

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

17 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts


Level 3 Expert

79865 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides