Question about 2003 Ford E-Series

Open Question

The lower front shock bolt broke off and I can't get it out.

The lower front shock bolt snapped off and I can't get it out.

Posted by on

  • cabrooster Aug 10, 2008

    I have a 2002 E150 and also snapped off the shock bolt. This bolt appears to be pressed into the lower control arm, with a screwed-on bushing that the shock slips over, then (if one had a long bolt prior to snapping) could be secured with a nut that has an integrated washer.

×

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Steps to replace 2007 dodge dakota tront shocks from strut spring assembly


Hello Russell,

If you replacing the front struts as an assembly the springs will be equipped and ready to install.

If your purchasing the strut assembly without the coil springs you will need a spring compressor.

  1. Before servicing the vehicle a service manual for safety precautions should be consulted.
  2. Raise and support the vehicle.
  3. Remove the tire and wheel assembly.
  4. Support the lower control arm outboard end.
  5. Remove the upper shock nuts.
  6. Remove the stabilizer link lower nut and then separate the stabilizer link from the lower control arm to gain access to the lower shock bolt.
  7. Remove the lower shock bolt.
  8. Remove the shock.
To install:
  1. Install the upper part of the shock into the frame bracket.
  2. Install the nuts. Tighten to 45 ft. lbs. (61 Nm).
  3. Install the lower part of the shock into the lower control arm. Tighten the bolt to 155 ft. lbs. (210 Nm).
  4. Install the stabilizer link lower nut to the lower control arm.
  5. Remove the support from the lower control arm outboard end.
  6. Install the tire and wheel assembly.
  7. Remove the support and lower the vehicle.

Jul 27, 2016 | Dodge Cars & Trucks

1 Answer

Dakota front shock


If the head of the bolt broke off, you're going to have to drill the bolt out with a carbide bit.

Oct 26, 2013 | Cars & Trucks

2 Answers

How to replace rear shocks on a 2006 cadillac srx Have 125,000 miles on car and need to replace rear shocks


Your car should have different shocks from most cars, with the magnetic, electrical charge viscosity change. Be sure that the shocks are actually not functioning correctly.

Sep 13, 2010 | 2006 Cadillac SRX

1 Answer

How to change 2007 dodge 1500 front struts?


Removal & Installation Independent Front Suspension – 2WD Vehicles To Remove:
  1. Before servicing the vehicle, refer to the precautions at the beginning of this section.
  2. Safely raise and support the vehicle.
  3. Support the lower control arm outboard end.
  4. Remove or disconnect the following:
    • Upper shock absorber nut, retainer and grommet
    • Lower nuts and shock absorber
To Install:
  1. Install or connect the following:
    • Lower retainer and grommet on the shock absorber stud and insert shock absorber through frame bracket hole
    • Lower nuts
      1. Torque to: 25 ft. lbs. (34 Nm)
    • Upper grommet, retainer and new nut (or existing nut with Mopar Lock N Seal or Loctiti 242) on the shock absorber stud
      1. Torque to: 40 ft. lbs. (54 Nm)
  2. Remove support from lower control arm outboard end.
  3. Lower the vehicle.
Independent Front Suspension – 4WD Vehicles To Remove:
  1. Before servicing the vehicle, refer to the precautions at the beginning of this section.
  2. Safely raise and support the vehicle.
  3. Remove tire and wheel assembly.
  4. Support the lower control arm outboard end.
  5. Remove or disconnect the following: dod_ram15_02-04_4wd_shock.gif

    • Upper shock nut with insulator and retainer
    • Lower shock bolt
    • Shock absorber
To Install:
  1. Install or connect the following:
    • Upper part of shock absorber into frame bracket with insulators and retainers and nut
      1. Torque to: 40 ft. lbs. (54 Nm)
    • Lower part of shock absorber into lower control arm with the bolt
      1. Torque to: 100 ft. lbs. (135 Nm)
  2. Remove support from lower control arm.
  3. Install tire and wheel assembly.
  4. Lower the vehicle.
Link/Coil Front Suspension To Remove:
  1. Before servicing the vehicle, refer to the precautions at the beginning of this section.
  2. Remove or disconnect the following:
    • Nut, retainer, and grommet from upper stud in engine compartment dod_ram15_02-04_shock.gif

    • Nuts from upper shock bracket
  3. Lower bolt from axle bracket and shock absorber from engine compartment
To Install:
  1. Position lower retainer and grommet on upper stud and insert the shock through the spring from the engine compartment.
  2. Install or connect the following:
    • Lower bolt
      1. Torque to: 100 ft. lbs. (135 Nm)
    • Upper shock bracket and nuts
      1. Torque to: 55 ft. lbs. (75 Nm)
    • Upper grommet, retainer and upper shock absorber nut
      1. Torque to: 35 ft. lbs. (47 Nm)
prev.gif next.gif

Jul 22, 2010 | 2007 Dodge Ram Truck

1 Answer

How do you remove the front shocks on a 2004 Dodge Durango 4X4?


how do you remove the front shocks on a 2004 durango limited 4x4. the stabilizer bar and axle links appear to be the way for removing the lower shock mounting bolt

Apr 29, 2010 | 2004 Dodge Durango

1 Answer

Replacing front struts


Okay....here is the steps first....and then the directions on how to use the tools:

  1. Raise and properly support the vehicle.
  2. Remove the front wheel.
  3. Detach the shock absorber lower mount by removing the two bolts.
  4. Remove the retainer nut, retainer, cushion and shock absorber.
  5. Detach the cushion retainer from the shock absorber.
  6. Compress the coil spring with a commercially available spring compressor.
  7. Detach the stabilizer bar.
  8. Support the upper suspension arm and steering knuckle securely.
  9. Remove the cotter pin.
  10. Loosen and remove the nut.
  11. Using a ball joint removal tool, detach the lower ball joint from the lower control arm.
  12. Loosen the suspension arm set bolt.
  13. Remove the suspension arm set bolt nut.
  14. Remove the nut from the strut bar front set bolt.
  15. Pull out both set bolts.
  16. Remove the lower suspension arm and coil spring. To install:
  17. Installation is the reverse of removal. Note the following torque specifications:
    1. Strut bar front set bolt: 221 ft. lbs. (300 Nm)
    2. Lower suspension arm set bolt: 148 ft. lbs. (200 Nm)
    3. Lower ball joint nut: 80 ft. lbs. (110 Nm)
    4. Lug nuts: 83 ft. lbs. (110 Nm).

May 13, 2009 | 1998 Toyota Tacoma

1 Answer

I am trying to get the wheel assembly apart to change the front bearings on a 1996 mercury villiger


http://groups.yahoo.com/group/villagerquest/

9ad2184.gif
Item Part Number Description 1 — Cotter Pin 2 — Nut Retainer 3 1131 Insulator 4 3B477 Front Axle Wheel Hub Retainer 5 1195 Front Wheel Outer Bearing Retainer Washer 6 1104 Wheel Hub 7 1107 Lug Bolt 8 3K050 Snap Ring 9 3123 Front Wheel Bearing 10 2K004 Front Disc Brake Rotor Shield 11 3130 Front Wheel Knuckle

Wheel Hub, Wheel Knuckle and Wheel Bearing SPECIAL SERVICE TOOL(S) REQUIRED Description Tool Number Tie Rod End Separator T85M-3395-A
Removal
  1. Raise and support the vehicle.
  2. Remove the wheel (1007) and tire assembly.
  3. NOTE: It is not necessary to disconnect the front brake hose (2078).

    Remove the disc brake caliper (2B120) and suspend it with mechanic's wire out of the way. Refer to Section 06-03 for the removal procedure.
  4. Remove the front disc brake rotor (1125).
  5. Remove and discard the cotter pin.
  6. Remove the nut retainer and insulator.
  7. Remove the front axle wheel hub retainer (3B477) and the front wheel outer bearing retainer washer (1195).




  8. Remove and discard the cotter pin from the front suspension lower arm ball joint (3050).
  9. Loosen the front suspension lower arm ball joint nut until it contacts the front wheel driveshaft joint.


    stv~us~en~file=f8063b.gif~gen~ref.gif

  10. Strike the front wheel knuckle with a hammer while pulling down on the front suspension lower arm (3078) until the front suspension lower arm ball joint separates from the front wheel knuckle.




  11. Remove the front suspension lower arm ball joint nut.




  12. Remove the front suspension lower arm ball joint from the front wheel knuckle.
  13. Remove and discard the cotter pin.




  14. Remove the tie rod end nut.




  15. Use Tie Rod End Separator T85M-3395-A to separate the tie rod end (3A130) from the front wheel knuckle.




  16. Remove the front brake anti-lock sensor bolt.




  17. Remove the two front shock absorber-to-front wheel knuckle nuts.




  18. Remove the two front shock absorber-to-front wheel knuckle bolts.
  19. Remove the front shock absorber (18124) from the front wheel knuckle.
  20. Use 2-Jaw Puller D80L-1002-L, or equivalent, to separate the front wheel driveshaft and joint (3B436) from the front wheel knuckle.
  21. Remove the front wheel hub, front wheel knuckle and front wheel bearing as an assembly from the vehicle.
  22. If necessary, match mark and remove the steering stop bolt and steering stop bolt jam nut from the front wheel knuckle.




Installation
  1. Position the front wheel hub, front wheel knuckle and front wheel bearing as an assembly on the front wheel driveshaft and joint.
  1. Install the front wheel knuckle into the front shock absorber.
  1. Install the two front shock absorber-to-front wheel knuckle bolts.
  1. Install the two front shock absorber-to-front wheel knuckle nuts. Tighten the front shock absorber-to-front wheel knuckle nuts to 113-123 Nm (83-91 lb-ft).

Apr 10, 2009 | 1996 Mercury Villager

1 Answer

Shocks


rear
5955ba5.gif ------------------------------------------------------------------------------------------

front

Removal
  1. Remove front shock absorber-to-upper shock bracket nut and bolt.
  1. Disconnect the lower end of the front shock absorber bolt and nut from the U-bolt plate.
  1. Compress the front shock absorber and remove.
Installation
  1. Insert front shock absorber into the front shock absorber mounting bracket (18183). Insert bolt and tighten nut to 60-81 Nm (45-60 lb-ft).
  1. Attach the lower end of the front shock absorber to the U-bolt plate by installing the nut and bolt. Tighten to 60-81 Nm (45-60 lb-ft).
---------------------------------------------------------------------------------------------

front


Feb 04, 2009 | 1996 Ford F350 Crew Cab

1 Answer

How to take off & install front shocks on a 2002 Chevrolet S-10


NOTE Hold the shock absorber stem with a wrench while backing the nut off.
Wheel Mounting nut


Retaining nut and grommet Shock absorber-to-lower control arm bolts Shock absorber Replace the parts, as necessary.

0900c1528024dc58.jpg enlarge_icon.gifenlarge_tooltip.gifFig. Front shock absorber mounting-2WD vehicles


To install:
  1. Fully extend the shock absorber stem, then push it up through thelower control arm and spring so that the upper stem passes through themounting hole in the upper control arm frame bracket.
  2. Install or connect the following:

    Retaining nut and grommet on the stem. Tighten the nut to 106 inch lbs. (12 Nm).


    Shock absorber-to-lower control arm bolts and tighten to 22 ft. lbs. (30 Nm) Wheel

Oct 17, 2008 | 2001 Chevrolet S-10

Not finding what you are looking for?
2003 Ford E-Series Logo

Related Topics:

104 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

70387 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22041 Answers

Ron Lankford

Level 3 Expert

5386 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...