Question about Chevrolet S 10

1 Answer

Is there band adjustment on chevy s-10 - S 10 Chevrolet Cars & Trucks

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Chevrolet Master
  • 2,007 Answers

No.

Posted on Mar 20, 2011

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2000 chevy 3500 4l80 trany where is band or clutch adjustment located for reverse


The band is on the inside of the transmission. There isn't an adjustment.

Jul 12, 2015 | Cars & Trucks

2 Answers

How do you tighten bands on a 1997 Chevy Blazer


Not adjustable on newer model vehicles

May 23, 2014 | 1997 Chevrolet Blazer

1 Answer

How do you tighten transmission bands in a 1997 Chevy Blazer


These bands are no adjustable by turning an adjuster there are adjusted by a measurement once fully applied and the apply pin come in different lengths.

May 23, 2014 | 1997 Chevrolet Blazer

1 Answer

5r55w od and intermediate band adjustment


The bands should be tightened all the way with 10 ft-lbs on the adjuster bolt then 2 turns out and locked at that position

May 22, 2014 | 2003 Ford Explorer

1 Answer

I have a 10" band saw model 124.214000 how much tension do i need put on blade or the proper way to adjust the tension.


I've been having hard times also putting right tension on my Haltbar blade . Try reading this blog : http://bandsawblog.com/blade-tension/
Hope that helps.

Feb 08, 2013 | Cars & Trucks

1 Answer

1981 chevy truck that will only go in reverse, other gears will move it, but very slowly and at very high RPMs. Could this be torque converter, drivebands in transmission, or something else?


Transmission slipping,this is not the torque convertor, you would not even have reverse, You can adjust the band, when you adjust the band in doing so it holds the transmission drum and there it transfers power,So the transmission band is worth your try, if it fails you need a transmission

Nov 26, 2012 | Cars & Trucks

1 Answer

Automatic transmission service adjustments for 2000 mazda bravo


There should not need to be any "adjustments" for a normal fluid and filter service for your vehicle, unless you have replaced some parts of your transmission that requires adjustment such as the gearshift lever, intermediate and overdrive band, throttle cable, or transmission range sensor/switch.

With that said, the band adjustment specs are "Tighten the band adjusting screw to 10 Ft.Lbs. (14 N.m.) then back off 2 full turns. While holding band adjusting scew stationary, tighten the locking nut to 35-45 Ft.Lbs. (48-61 N.m.)

Jun 16, 2012 | Cars & Trucks

1 Answer

Automatic transmission band adjustment in a 1997 chevy blazer


I have a 1995 Chevy 1500 4.3 v6 trans bands need to be adjusted I have two out of the four gears. Reverse tends to slip but works. How do I adjust the bands. And what side are they on. I baught it as is.

Sep 20, 2010 | 1997 Chevrolet Blazer

1 Answer

Transmition adjustments


Sorry, Reverse isn't controlled by a band on the 4L60E. Reverse is controlled by two clutches. The trans will need rebuilt to fix the problem.

Jul 11, 2010 | 1995 Chevrolet Silverado 2500

1 Answer

Jeep grand cherokee revs for to high before changing gear


Message:
My 2002 Dakota has been somewhat confused about shifting as well. It showed a code P1762. I dropped the pan to install a new fluid filter and fluid-(use only ATF+3 or ATF+4). Since the pan was off I decided to adjust the bands. The front band controls the 2nd gear cluster. The rear band controls the 3rd gear cluster and reverse. For a 2-3 shift, the transmission shifts back to 1st gear with the front band while the rear band engages 3rd gear. If the front band does not release the 2nd gear clutches before the third gear clutches engage, the transmission binds, which shortens the life of the transmission clutches. If the front band releases too early in the shift, the engine will overspeed (sounds and feels like a slip) during the 2-3 shift.
The front band adjusting screw is on the driver's side above the shift linkage. The rear band is inside the fluid pan near the filter.
1. Loosen band adjusting screw locknut. Then back locknut off 3-5 turns. Be sure adjusting screw turns freely in case. Apply lubricant to screw
threads if necessary. The front band adjuster is on the outside of the transmission and the locknut requires a 3/4" wrench.

2. Using Inch Pound Torque Wrench C-3380-A, a 3-in. extension and appropriate Torx� socket (T-40), tighten adjusting screw to 72 in-lb. CAUTION: If Adapter C-3705 (from SPX Miller) is needed to reach the adjusting screw, tighten the screw to only 47-50 in. lbs. torque.

3. Back off adjusting screw the number of turns listed below for your transmission.

4. Hold adjusting screw in place and tighten lock-nut to:

41 N�m (30 ft. lbs.) for the front band
34 N�m (25 ft. lbs.) for the rear band
The adjustment screw inside the case is a square head bolt. You will need a 1/4 square head socket to fit your torque wrench.
Band adjustments for each model year:
1994

* Front Band - tighten to 72 in-lb, back off 2-1/2 turns (all transmissions)
* Rear Band
o 32/42RH - Tighten to 72 in-LB, back off 4 turns
o 36/37/46/47RH - Tighten to 72 in-lb, back off 2 turns

1995-1996

* Front Band
o 42RH - tighten to 72 in-lb, back off 2-1/4 turns
o 46RH - tighten to 72 in-lb, back off 2-7/8 turns
o 47RH - tighten to 72 in-lb, back off 1-7/8 turns
* Rear Band
o 42RE/RH - tighten to 72 in-lb, back off 4 turns
o 46RE/RH - tighten to 72 in-lb, back off 2 turns
o 47RE/RH - tighten to 72 in-lb, back off 3 turns

1997-1998

* Front Band
o 42RE - tighten to 72 in-lb, back off 3-5/8 turns
o 46RE - tighten to 72 in-lb, back off 2-7/8 turns
o 47RE - tighten to 72 in-lb, back off 1-7/8 turns
* Rear Band
o 42RE - tighten to 72 in-lb, back off 4 turns
o 46RE - tighten to 72 in-lb, back off 2 turns
o 47RE - tighten to 72 in-lb, back off 3 turns

1999

* Front Band
o 42RE - tighten to 72 in-lb, back off 3 turns. (TSB 21-16-98)
o 47RE - tighten band adj. screw to 72 inch pounds, back off 1 7/8 turns
* Rear Band
o 47RE - tighten band adj. screw to 72 inch pounds, back off 3 turns
+ The 47RH rear band requires a 1/4" hex driver, the front band requires a
T-30 Torx driver, the filter is held in place by two screws which require a T-20 Torx drive

2000-2002

* Front Band
o 42RE - Tighten band adj. screw to 72 in-lb, back off 3 turns
o 44RE - Tighten band adj. screw to 72 in-lb, back off 1 7/8 turns
o 46RE - Tighten band adj. screw to 72 in-lb, back off 2 7/8 turns
o 47RE - Tighten band adj. screw to 72 in-lb, back off 1 7/8 turns
From Bill Konolday's 47RE notes: I usually go a little looser than factory
specs on this front band - backing off the adjustment screw 2 or 2 1/4 turns.
Depending on the circumstances I have backed off the band up to 2 1/2 turns.
* Rear Band
o 42RE - tighten band adj. screw to 72 inch pounds, back off 4 turns
o 44RE - tighten band adj. screw to 72 inch pounds, back off 4 turns
o 46RE - tighten band adj. screw to 72 inch pounds, back off 2 turns
o 47RE - tighten band adj. screw to 72 inch pounds, back off 3 turns

2003

* Front Band
o 48RE - tighten band adj. screw to 72 inch pounds, back off 1-3/4 turns
* Rear Band
o 48RE - tighten band adj. screw to 72 inch pounds, back off 3 turns

2005

* Front Band
o 48RE - tighten band adj. screw to 72 inch pounds,
back off front band adjusting screw 1-3/4 turns for diesel vehicles,
or 1-1/2 turns, for V-10 vehicles.
* Rear Band
o 48RE - tighten band adj. screw to 72 inch pounds, back off 3 turns

94+ Automatic Transmission Bolt and Nut Torque Specs

* Front band adjustment locknut - 30 ft-lb
* Rear band adjustment locknut - 25 ft-lb
* Transmission pan bolts - 13 ft-lb
I just replaced the solenoid with the recommended transducer and all is fine now. The transducer cost me about $50 at a nearby dealership.
Hope this helps. -zman. rroszman@yahoo.com

Dec 09, 2008 | 2001 Jeep Grand Cherokee

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

38 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

75797 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8140 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...