Question about 2003 Chevrolet Tahoe

1 Answer

Removing rear break pads, how do the top and bottom pins come out

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    MVP:

    An expert that gotĀ 5 achievements.

    Master:

    An expert who has achieved Level 3.

    Sergeant:

    An expert that hasĀ over 500 points.

  • Master
  • 411 Answers

14 mm socket

Posted on Mar 20, 2011

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Replacing front brake pads 2001FXST


Front Brake Caliper: All But FLSTS/FXSTS

Remove the front master cylinder reservoir cap to be able to check the fluid level as the caliper pistons are pushed back into the caliper because the fluid level may rise more than the 1/8 in. (3.2 mm) from the top level and you may have to remove some excess fluid if it does so. THEN loosen but do not remove both pad pins with a 12 point one quarter inch socket. THEN remove both metric caliper mounting bolts and remove the caliper from the front forks and brake disc and pry the pads back to force all four caliper pistons into their bores. THEN once the pistons have been retracted, remove the pad pins and the brake pads.


Although the front and rear brake calipers except FXSTD models, use the same exact brake pad set the FXSTD does not and the FXSTD rear pads have a vertical slot cut into the pads. Be sure NOT to substitute front and/or rear brake pads for the other on these bikes. On the right side of the vehicle the pad with the two tabs installs on the inboard side of the caliper and on the left side of the vehicle, the pad with the two tabs installs on the outboard side of the caliper.


THEN install new pads into the caliper noting that the curved portion of the pad faces to the rear of the bike, and loosely install the pad pins until you hear an audible click from them. THEN re-attach the caliper to front fork, place the caliper over the brake disc with the bleeder valve facing upwards, loosely install the long caliper mounting bolt into the top hole on the fork leg, install the short mounting bolt into the bottom hole on the fork le, tighten the bottom mounting bolt to 28-38 ft-lbs (38.51.5 Nm) and final tighten the top mounting bolt also to 28-38 ft-lbs (38.51.5 Nm) and final tighten the two pad pins to 180-200 in-lbs (20.3-22.6 Nm).


THEN and whenever new pads are installed, before moving the bike pump the brakes until brake fluid pushes the caliper pistons and the pads out and verify that the pads are against the brake disc and then rotate the wheel to ensure there is not any excessive drag between the pads and the disc, check for proper fluid level in the reservoir and if necessary top it up with DOT 5 Silicone base brake fluid only, install the reservoir cover and tighten its screws to 6-8 in-lbs (0.7-0.9 Nm).


THEN and whenever any work has been done on brakes always test the brakes at low speed before operating on a roadway or at higher speeds. THEN test brake system light and if during the road test the brakes feel spongy at all bleed the system and after obtaining a hard lever or pedal road test the bike again.

Oct 04, 2014 | Cars & Trucks

1 Answer

Step by step instructions on how to replace front break pads on a 2003 VW Passat


For front brake pads replacement you need only usually wrench set, inclusive 7 mm allen key also.
But for rear brake pads replacement you need obligatory a special caliper piston pressing tool, in order to press back rear caliper piston with parking brake automatic adjustment!!!
For front brake pads. First you must verify yours front brake disc diameter: 280 mm or 288 mm. After that you can buy the brake pads (with wear sensor). For change front brake pads you must raise vehicle, remove wheels, extract the retaining spring of the caliper, and remove the caliper as follow:
1. Do not disconnect the brake hose from the caliper, and do not allow the caliper to hang by the brake hose!
2. Remove top and bottom caps (on back side of the caliper) for access to guide pins, then unbolt and remove them from the brake carrier. Remove the caliper.
3. Now you must thoroughly clean the brake calipers (free of grease).
4. Remove outer brake pad from brake carrier.
5. Pull inner brake pad out of brake caliper piston.
6. Check up the brake fluid level on the reservor, and emptying if neccessary!
7. Push piston back into brake caliper housing.
8. Install inner brake pad (with expanding spring) in brake caliper piston. (Arrow marked on pad - if exist, must point in direction of brake disc rotation when vehicle is moving forward).
9. Install outer brake pad into brake carrier.
10. Bolt brake caliper housing to brake carrier using two guide pins. Tightening torque is 25 Nm.
11. Install both caps.
12. Insert retaining spring into brake caliper housing. Important: Depress the brake pedal firmly several times while the car is stationary so that the brake pads adjust to their normal operating positions!!! Check brake fluid level and top up if neccessary!!!

Mar 10, 2011 | Volkswagen Passat Cars & Trucks

1 Answer

How to change rear brake shoes


Tools

Needle Nose Pliers
Hammer
Phillips Screwdriver
9/16 Socket and ratchet (not a deep socket)
Large C-Clamp
Center Punch

1. Put front of vehicle on jack stands. Brace back wheels
2. Remove front wheel.
3. Using the C-Clamp squeeze the caliper so the piston goes back inside the caliper.
4. Using the 9/16 socket undo the 2 bolts that go through a rubber boot. There's one on the top of the caliper and the other one is the bottom of caliper. The reason I said not to use a deep socket is that the torsion bar link is kinda in the way so you can't fit a deep socket in there.
5. Once the 2 bolts are removed, remove the wire retaining clips. One wraps around the top pin that holds the brake pads together and the other clips onto the top and bottom pin. Remove the one that goes from the top pin to the bottom pin. You will not be able to take the other one out just yet.
6. Using your center punch or screw driver tap both pins out of the caliper. You will at this point be able to remove the other wire retaining clip.
7. At this point the caliper should be loose and you should be able to remove it. If you are just changing the brake pads then you're half way done. Replace old pads with new pads and reassemble in the reverse order.
8. If you are replacing the rotors as well then all you need to do is loosen both Phillips head screws that are holding the rotors to the hub. Be careful with the screws I happened to strip the head on one of these babies and let me tell ya it wasn't easy taking it out. Once the screws are removed the rotor should come right off. Might need a hammer to persuade it a little.

9. Install new rotor and brake pads and you are done.

Feb 04, 2011 | 2001 Kia Rio

1 Answer

Will I need a caliper reset tool kit to change the brakes on my 2007 toyota sienna or will a standard c-clamp do the job? And since it is an ABS system, I assume that brakes must be bled, correct?


Brake Pads Removal & Installation Front To Remove:
  1. Remove the front wheels. Front brake caliper (exploded view) toyota-09-00-5838.gif

  2. Loosen the caliper bleeder.
  3. Hold the slide pin; remove the 2 mounting bolts and remove the brake caliper from the support.
  4. Support the caliper.
  5. Open the brake bleeder. Press the caliper piston into the bore.
  6. Close the bleeder after the piston has reached the bottom of the caliper bore.
  7. Remove the brake pads, support plates, wear indicators and anti squeal shims.
  8. Remove the slide pins and bushings from the caliper support.
To Install:
  1. Lubricate the slide pins and bushings with brake grease.
  2. Install the bushing on the slide pin.
  3. Install the slide pin on the caliper support.
  4. Install the brake pad support plates on the caliper supports.
  5. Lubricate the anti squeal shims with brake grease.
  6. Install the anti squeal shims on the brake pads.
  7. Install the pad wear indicator facing upward and install the pads on the caliper support.
  8. Install the caliper on the support.
  9. Install the 2 mounting bolts, hold the slide pins and tighten 25 ft-lb (34 Nm).
  10. Fill the reservoir and bleed the brakes.
  11. Install the front wheels.
Rear To Remove:
  1. Remove the rear wheels.
  2. Loosen the caliper bleeder. Rear brake caliper (exploded view) toyota-09-00-5842.gif

  3. Hold the slide pin; remove the 2 mounting bolts and rear brake caliper assembly from the support.
  4. Support the caliper.
  5. Open the brake bleeder. Press the caliper piston into the bore.
  6. Close the bleeder after the piston has reached the bottom of the caliper bore.
  7. Remove the brake pads, support plates, and anti squeal shims.
  8. Remove the slide pins from the caliper support.
To Install:
  1. Lubricate the slide pins with brake grease.
  2. Install the slide pin on the caliper support.
  3. Install the brake pad support plates on the caliper supports.
  4. Lubricate the anti squeal shims with brake grease.
  5. Install the anti squeal shims on the brake pads.
  6. Install the rear pads on the caliper support.
  7. Install the rear caliper on the support.
  8. Install the 2 mounting bolts, hold the slide pins and tighten 25 ft-lb (34 Nm).
  9. Fill the reservoir and bleed the brakes.
  10. Install the front wheels.
prev.gif next.gif

Sep 18, 2010 | 2007 Toyota Sienna

1 Answer

Removing breaks from a 2000 Hyundai Accent


hi from uk the 17mm bolts you mention do not remove as these secure the caliper carrier and only need removing to facilitate disc/rotor renewal to remove caliper only if you check the rear of caliper you will see two 13mm blts top and bottom of caliper these bolts pass thro conveluted rubber boots into slide pins bolts screw into these pins and the caliper is what is known as floating caliper this means only one piston operation on caliper then caliper slides on pins tou operate both pads when brakes applied so remove the two bolts and the steel spring on front face of caliper ?(remember how it fits !) then caliper slides off the rotor leaving pads in place on the carrier you then prise out pads/wirebrush carrier points where new pads are to fit then push caliper piston back then refit caliper in reverse order ADVICE= before refitting caliper smear alittle copper grease on rear metal side of each pad this prevents squeeling of pads when braking also pull out the to pins mentioned above that fit into carrier top/bottom wipe clean and put /smear copper grease on these too then refit and push in till rubber boots reseat on the carrier lips ? when you have done both sides brakes bleed calipers this is a must ! and when you do you will see dirty fluid emmited on the fist couple of pumps on b/pedal then clean fluid ? this WILL improve b/pedal travel and more positive ? the dirty fluid is o/heated /burnt fluid which becomes compressable giving soft pedal when operated and is due to heat transfer from disc/pads over time and is conducted thro caliper piston to fluid that is why it is recommended you bleed/flush hydraulics at least 2year intervals hope the above helps you and understandable best wishes from uk

Apr 09, 2010 | 2000 Hyundai Accent

1 Answer

Changing rear brake pads on 2002 buick lesabre


Your correct, does hinge on top bolt and then is ussually stiff pulling from pin, but it will move

Jun 30, 2009 | 2005 Buick LeSabre

1 Answer

Changing front and rare break pads in hyundia excel


this front::
  1. Raise and support vehicle, then remove wheel/tire assembly.
  2. Remove lower bolt and caliper assembly. Position assembly aside using suitable wire.
  3. Remove brake pads and shim.
  4. Bottom piston in caliper using suitable tool.
  5. Install new brake pads and attach shim to the outer pad. Tighten lower bolt to specifications.
this for rear::

1. Raise and support vehicle, then remove wheel/tire assembly.
  1. Remove axle nut, then the hub and drum assembly.
  2. Remove end shoe springs, cylinder and hold-down spring.
  3. Remove shoes and adjuster as an assembly.
  1. Reverse removal procedure to install, noting the following:
    1. Apply suitable grease to backing plate shoe contact surfaces.
    2. Install shoe hold-down pin, then assemble return spring with the pushrod shortened.
    3. Pull parking brake lever fully upward. Repeat process several times.

Jun 04, 2009 | 1994 Hyundai Excel

1 Answer

The top bolt that holds the caliper on looks to need a special tool the bottom is just a socket what takes off the top bolt on the rear?


Hi the top is not a bolt its a pin
to remove the caliper remove the lower bolt then lift the caliper up till it clears the brake pads and slide the caliper off the pin
when you reinstall lube the top pin and the bottom slide pin
TAKE CARE WHEN REMOVING THE LOWER BOLT THEY BREAK EASY

May 05, 2009 | Buick Park Avenue Cars & Trucks

2 Answers

Rear brake caliper removal


I just did the rear caliper on my '95 Deville Concours and found that the caliper would not rotate enough to slide it off the top bolt. My solution was to remove the parking brake cable bracket bolt behind the caliper. This gave me the ability to rotate the caliper enough to get the caliper off of the brake pads and slide the caliper towards the inside of the car.

Apr 22, 2009 | 1995 Cadillac DeVille

1 Answer

Rear brakes


NEED A 17MM SOCKET TO REMOVE THE REAR TIRES, THEN THERE IS A PIN THAT HOLD THE TOP OF THE PADS IN. YOU MUST REMOVE THAT PIN WITH A TYPE OF PUNCH AND USE A HAMMER . PUNCH IT OUT THEN REMOVE ONE PAD, PUSH THE PISTON IN THEN THE OTHER PAD. PUT THE PIN BACK IN PLACE, DO THE SAME TO THE OTHER SIDE

Mar 24, 2009 | 2003 Mercedes-Benz C-Class

Not finding what you are looking for?
2003 Chevrolet Tahoe Logo

Related Topics:

23 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

75817 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8180 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...