Question about Jeep Wrangler

1 Answer

Can not locate egr valve - Wrangler Jeep Cars & Trucks

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Expert
  • 80 Answers

Its on the cylinder head right hand side by the exhaust manifold/

Posted on Aug 02, 2008

6 Suggested Answers

chuck943
  • 783 Answers

SOURCE: egr valve location

here is a pic of it.
[IMG]http://i253.photobucket.com/albums/hh43/chuck943/V2903019.gif[/IMG]

Posted on Mar 02, 2009

  • 398 Answers

SOURCE: egr valve location

The EGR Valve Location is typically housed on the intake manifold this schematic may help you
http://www.autozone.com/shopping/repairGuide.htm?pageId=0900c1528008822d

Posted on Mar 07, 2009

c17hydro
  • 2984 Answers

SOURCE: Location of EGR Valve

Found the info!!

This Dodge EGR valve is a certain kind of device that is mounted right on your intake manifold which controls the amount of exhaust gasses back into your engine.
On a 2005 Dakota with 4.7 liter engine (non-HO), the EGR valve is located near the intake manifold on the driver's side right up against the firewall. It's hard to spot as it sits lower than the intake manifold. To change it, remove the electrical connector. There's a red tab that needs to be pushed to one side and then you have to squeeze down on a tab to get it free. Using a 13 mm socket, remove the bolt that you can see. I had to use a 3 inch wobble extention and then a 8 inch extension with a deep well socket to reach it with my 3/8 inch ratchet. There's a second bolt that you can't see between the EGR valve and the firewall. With a little trial and error and a lot more luck, you can reach the hidden bolt with the 3 inch wobble extension and a 13 mm deep well socket. Attach the ratchet after the socket is on and remove. This one isn't easy and if there's any Dodge engineers reading this one, a couple of extra inches of clearance between the valve and the firewall wouldn't have killed you no matter what the cost accountants said. With both bolts removed, you should be able to pull out the metal pipe that connects the manifold to the EGR valve out of the manifold (Pull to the right) and then you can lift the valve out. For assembly, the metal pipe connecting the intake manifold the EGR valve has to be removed and reinstalled on the new valve. It's held on with 2 5/16th" bolts. You should put the rear bolt on tight, but leave the front bold loose for the reinstall as some adjustment is necessary to get it put back together and the rear is a pain to tighten when installed. Line up the bolts that attach the valve and get the rear 13 mm bolt (The one you couldn't see on disassembly) started. Do not start the other 13 mm bolt as you'll need to pivot the valve and pipe to the left in order to reinsert the pipe into the intake manifold. Once the pipe is in the intake manifold. Start the other 13 mm bolt and tighten both 13 mm bolts and then the 5/16" bolts holding the pipe onto the valve. Reinstall the electrical connection. Please don't forget to rate!!!!

Posted on Mar 14, 2009

Murphybanton
  • 2004 Answers

SOURCE: location of egr valve?

The EGR Valve and transducer is mounted near the throttle body. 42224993.gif

Visit http://autorepair.about.com/library/faqs/bl948e.htm


Rate this fixya.

Posted on May 27, 2009

ZJLimited
  • 17970 Answers

SOURCE: egr valve location on dodge ram 2005 4.7

The EGR, or exhaust gas recirculation valve, takes inert exhaust gasses drawn from the exhaust system and reintroduces them into the combustion chamber through the intake manifold. This process lowers the peak combustion temperature and helps combat the formation of Nitrous Oxide (NOx) in the exhaust.

f0255cf.jpg

  1. Separate the intake ducts from the air cleaner assembly by loosening the retaining clamps and pulling the ducts away from the housing.
  2. Disconnect the vacuum line from the air cleaner assembly.
  3. Remove the wing nut that secures the air cleaner housing lid to the base.
  4. Remove both the air cleaner hosing lid and base.
  5. Locate the EGR valve. Look at the front of intake manifold. The EGR valve will be bolted to the intake manifold just in front of the carburetor.
I hope help you with this. Good luck.

Posted on Sep 07, 2009

ZJLimited
  • 17970 Answers

SOURCE: were is the egr valve located for mazda rotege5

2002 Mazda Protege5 with the FS2.0 Motor. The EGR Valve is located below the throttle-body. You must take off the Intake tube to get a good view of it. To replace it I think you might have to take off the throttle-body.

0335fe8.jpg

Fig. Exploded view of the intake manifold assembly with 2.0L (FS) engine

Good luck (remember rated this).

Posted on Jun 25, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Erg flow insufficient


  • The DPFE (differential pressure feedback EGR) sensor is faulty and needs to be replaced
  • There is a blockage in the EGR (tube), most likely carbon buildup
  • The EGR valve is faulty
  • The EGR valve may not be opening due to a lack of vaccuum
It is quite common for people to just replace the EGR valve only to have the OBD code return. The EGR valve is not always the culprit.
  • Use a vacuum pump and pull the EGR valve open while monitoring engine RPM's & DPFE voltage. There should be a noticable difference in RPM's with the EGR open
  • Clean out the EGR valve and/or tubing to remove deposits
  • Check the voltage at the DPFE, compare to specified values (refer to a repair manual for your specific model)
  • Replace the DPFE sensor (with a good quality / OEM one)
  • Replace the EGR valve
The EGR valve is located in the engine compartment. Its should look this

2_7_2012_10_25_48_pm.jpg

Feb 07, 2012 | 2000 Mercury Sable

1 Answer

Is there an EGR valve on 01 Jeep Grand Cherokee 4.7 L, and if so where?


The EGR Valve is located on the rear, driver's side of the engine. It's a failry easy job, and you should be able to this yourself.

The electronic EGR valve and solenoid assembly is attached to the rear of the left cylinder head. An exhaust gas routing tube connects the EGR valve to the intake manifold.

2010-05-30_173844_1.gif
  • Remove electrical connector at top of EGR valve solenoid.
  • Remove tube mounting bolt at intake manifold.
  • Remove two bolts connecting EGR tube to valve assembly.
  • Remove gasket located between EGR tube flange and EGR valve assembly. 2010-05-30_173909_2.gif
  • Remove two EGR valve mounting bolts.
  • Separate valve assembly from engine.
  • Remove and discard metal gasket located between cylinder head and valve assembly.


Sep 30, 2011 | 2001 Jeep Cherokee

2 Answers

My car is a suzuki xl-7 2002. it's has a problem with an egr valve. How you can help,me please,and where is the egr valve is located.?


The EGR valve will be mounted on the intake manifold, and may have either wiring or a vacuum hose attached to it. Type 'EGR valve' into Google images, and you will see what it looks like.

Sep 25, 2010 | 2002 Suzuki XL-7

1 Answer

I cant locate the egr valve on a 1998 Dodge ram 1500 5.2 L


An EGR valve assembly located at the front of the intake manifold. The EGR valve is a poppet style valve (on/off only) and is controlled by an internal diaphragm.

af91f0c.jpg

Fig. EGR location and associated components-California diesel

Hope helps (remember to rate this and comment ).

Sep 14, 2010 | 1998 Dodge Ram 1500 4WD

1 Answer

Where is the egr valve on a 2005 dodge 1500 5.7L


The electronic EGR valve and solenoid assembly (3) is attached to the front of the right cylinder head (1). An exhaust gas routing tube connects the EGR valve to the intake manifold.

2efe0f8.gif

Disconnect electrical connector (1) from EGR solenoid (2). Remove two bolts (3) connecting EGR tube (4) to valve assembly. Remove gasket located between EGR tube flange and EGR valve assembly.

Remove two mounting bolts (2). Separate valve assembly (3) from cylinder head (1). Remove and discard metal gasket located between cylinder head and valve assembly.
The new EGR valve will come with a new metal gasket. You can reuse the smaller gasket for the metal pipe going to the egr valve as long as its not damaged.

TY for using Fixya; remember rated this post.

Apr 14, 2010 | 2005 Dodge Ram 1500

1 Answer

WHERE DO I LOCATE THE EGR VALVE ON MY 2001 CHEVY IMPALA 3.8 V6


The egr valve is located at the end of a hose that plugs into youe valve cover. It is pushed right into a rubber grommet that is located in one of the valve covers. I hope this helps. don.t forget to rate my nswer, thanks

Feb 27, 2009 | 2001 Chevrolet Impala

2 Answers

Location of the egr sensor on 2000 ford ranger


The EGR pressure sensor is located within inches of the EGR valve. The exact location varies depending on the engine (2.5L, 3.0L or 4.0L). It is usually attached to the upper intake manifold with two small bolts.

Feb 24, 2009 | 2000 Ford Ranger SuperCab

2 Answers

2005 Dodge 1500 code p0404 EGR valve.


The electronic EGR valve and solenoid assembly is attached to the rear of the left cylinder head ,

  1. Remove electrical connector (5) at top of EGR valve solenoid.
  2. Remove tube mounting bolt (1) at intake manifold.
  1. Remove two bolts (4) connecting EGR tube (1) to valve assembly.
  2. Remove gasket located between EGR tube flange and EGR valve assembly.
  3. Remove two EGR valve mounting bolts (5).
  4. Separate valve assembly (3) from engine.
  5. Remove and discard metal gasket located between cylinder head and valve assembly.
INSTALLATION
  1. Clean area at rear of left cylinder head where it joins base of EGR valve.
  2. Clean EGR tube where it joins EGR valve.
  3. Position new gasket between EGR valve and cylinder head.
  4. Position EGR valve to cylinder head. Install and tighten two bolts (5). Refer to Torque Specifications.
  5. Position new gasket between EGR tube flange and EGR valve assembly.
  6. Position EGR tube (1) to side of EGR valve and into intake manifold.
    1. Install EGR tube flange bolt (1) at intake manifold. Tighten bolt. Refer to Torque Specifications.
    2. Connect electrical connector (5) to top of EGR valve solenoid (2).Do a final tightening of two EGR tube bolts (4). Refer to Torque Specifications

Feb 05, 2009 | 2005 Dodge Ram 1500

2 Answers

EGR VALVE ON 96 FORD PROBE SE


If it's a 2.0L, 5 speed (1994-7) there are two DPFE solenoids (both w/ 3 vacuum ports) near the oil filter, which control the EGR valve. They are discontinued and impossible to find except on junked cars. (FORD #'s K5T44093-4)
I have to junk my 1996 Probe if I don't find them - Missouri emissions.

Aug 24, 2008 | 1996 Ford Probe

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

535 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts

yadayada
yadayada

Level 3 Expert

61249 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...