Question about Ford Expedition EL

Open Question

1998 iveco 75e15 6000cc engine cylinder head torques

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 1779 Answers

SOURCE: need torque settings for 1985 4A corolla cylinder head

hey, torque must be done in 3 steps:
1st 22 ft lbs
2nd 43 ft lbs
final 47 ft lbs
use this sequence of tightening:

9 - 3 -1 -6 -8
7 - 5 - 2 -4 - 10

Posted on Jan 14, 2009

c17hydro
  • 2984 Answers

SOURCE: cylinder head torque settings 1990 2.6L isuzu motor

From front to back is this:


7 3 1 5 9



8 4 2 6 10



First torque value is 58 ft lbs.....then final torgue is 72 ft lbs.

Posted on Mar 21, 2009

  • 701 Answers

SOURCE: torque specs for toyota tercel

Hello vienotkelly: The correct Main bolt torque is 42 foot pounds. The connecting rods torque to 29 foot pounds. The torque sequence for the head bolts and the correct way to tighten the bolts are attached to this reply. Thak You for using6bd0ae1.jpg FixYa. Roger

Posted on Apr 15, 2009

  • 88 Answers

SOURCE: Hi I'm looking for cylinder head torque settings for a 1992 BMW 316/318 e36

BMW cylinder torque setting all models

According to my service manual as follows.

Cyl head to engine block (torx e12 M10 bolts)

Stage 1 30nm (22 ft – lb)
Stage 2 + 90 degrees
Stage 3 + 90 degrees

Cyl head to lower timing chain cover 10nm (89in – lb)

The tightening sequence is from inside to outside crossover as normal. Loosening sequence is from outside to inside crossover. Remember to set torque wrench at low setting and work gradually up through the whole sequence until you get the desired torque.

Posted on Aug 29, 2009

inspectmycar
  • 233 Answers

SOURCE: 94 mazda B3000 3.0L cylinder head torque specs

Step 1 torque to 59 ft pounds
2. Loosen one full turn
3. 37 ft pounds
4. 68 ft pounds

Use torque sequence below
aca9f77.gif

Posted on Sep 17, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What causes Iveco trackker to overheat when the radiator is ok


Hi Tendai, Many problems can cause engine overheating, follow are some:- Make sure that the radiator pressure cap is in good condition and operating at the correct pressure. Make sure there are no leakages from core plugs or radiator hoses. Inspect the thermostat for correct operation and replace if required. Inspect and make sure that valve timing is correct. Make sure that cylinder head is not warped due to overheating. (This last will require removal of the cylinder head, engineering and reinitialisation using correct torques and sequences for removal and tightening. Regards John

Dec 08, 2013 | Cars & Trucks

1 Answer

Cylinder head bolt tightening sequence for isuzu rodeo 1998


1998 Isuzu Truck Rodeo 2WD 2.2L MFI DOHC 4cyl

The Head Bolt Torque

Torque sequence ----------------- front ' 7 3 1 5 9 ' of ' ' engine ' 8 4 2 6 10 ' ----------------- Step 1: torque bolts in sequence to 18 Ft/Lbs Step 2: turn bolts in sequence an additional 90-degrees Step 3: turn bolts in sequence an additional 90-degrees Step 4: turn bolts in sequence an additional 90-degrees recheck final torque in sequence

1998 Isuzu Truck Rodeo 2WD 3.2L MFI DOHC 6cyl

The Head Bolt Torque

Torque sequence -------------- front ' 6 1 3 7 ' of ' ' engine ' 5 2 4 8 ' -------------- Step 1: torque to 20 Ft/Lbs Step 2: torque to 47 Ft/Lbs recheck final torque in sequence

Jan 15, 2013 | 1990 Isuzu Spacecab

1 Answer

I need the tork spec on 1998 Buick 3800 block for the cylinder head.


hope this helps,

Torque sequence --------- front ' 6 1 3 7 ' of ' ' engine ' 8 4 2 5 ' --------- Step 1: torque bolts in sequence to 37 Ft/Lbs Step 2: torque all bolts in sequence an additional 120 degrees Step 3: torque bolts 1,2,3, & 4 an additional 30 degrees recheck final torque in sequence *** CAUTION ***engine uses Torque To Yield head bolts (TTY) thatpermanently stretch during the initial installation.New head bolts must be used when cylinder head isreplaced or re-installed to obtain proper torque.
always torque from center
Tighten each bolt an additional 90° in sequence.


0996b43f8021ae77.jpg

Jun 18, 2011 | 1998 Buick LeSabre

1 Answer

Correct pressure for torque the head of mazda pickup 1998


Since you didn't say which engine you have, I've pulled torque specs for 3 different engines. Also, since I can't include a diagram showing the relative locations of the numbered head-bolt locations, it would be a good idea for you to purchase a vehicle specific repair guide that will show this info.


Take particular note about the TTY (Torque to Yield) bolts used on 2 of the 3 engines shown. It is said that new head bolts MUST BE USED when head is replaced or re-installed to obtain the proper torque.



B2500 4 Cylinder

Torque sequence: --------- ' 10 6 2 4 8 ' front ' ' ' 7 3 1 5 9 ' -----------Step 1: torque in sequence to 51 Ft/Lbs Step 2: torque again in sequence to 51 Ft/Lbs Step 3: final tighten all bolts an additional 90 to 100 degrees recheck final torque in sequence *** CAUTION ***engine uses Torque To Yield head bolts (TTY) that permanently stretch during the initial installation. New head bolts must be used when cylinder head is replaced or re-installed to obtain proper torque.







B3000 3.0 6 Cylinder

Torque sequence ---------- ' 6 4 2 8 ' ' ' ' 5 1 3 7 ' ---------- Step 1: torque to 59 Ft/Lbs Step 2: loosen in sequence (1) full turn Step 3: torque to 41 Ft/Lbs Step 4: torque to 73 Ft/Lbs









B4000 4.0 6 Cylinder

Torque sequence --------- ' 5 1 3 7 ' ' ' ' 6 4 2 8 ' --------- Step 1: torque cylinder head bolts in sequence to 26 Ft/Lbs Step 2: torque cylinder head bolts to 56 Ft/Lbs Step 3: turn cylinder head bolts in sequence an additional 90-degrees recheck final torque in sequence *** CAUTION ***engine uses Torque To Yield head bolts (TTY) that permanently stretch during the initial installation. New head bolts must be used when cylinder head is replaced or re-installed to obtain proper torque.


Good luck with this job!

Feb 06, 2011 | 1998 Mazda Pickup

2 Answers

Torque settings for a hyundai accent 1500 1998 model torque settings for head , conrods and crank


cylinder head bolt torque

52-55 ft lbs. cold engine
59-63 ft lbs. hot engine

connecting rod cap nut 26-28 ft lbs. SOHC
connecting rod cap nut 23-26 ft lbs. DOHC

main caps 41-44 ft lbs.

Dec 19, 2010 | Hyundai Motor 1998 Accent

1 Answer

I need the torque sequence for a 1998 chevy cavalier head


There's two engine's, your car could have, 2.2L or 2.4L. so here's both, cylinder head torque for 2.4L engine.
Step # 1
Bolt's 1 - 8 40 Ft.Lbs
Bolt's 9 - 10 30 Ft.Lbs

Step # 2
All bolt's additional 90deg.

Hope this was very helpful.

cb3ba1f.gif
9568cea.gif

Sep 02, 2010 | 1998 Chevrolet Cavalier

3 Answers

Need to know the head bolts torch specs on 98 toyota v6


heres the torque specs and the way to tighten the head bolts for your 1998 toyota sienna, hope this helps,
12 point bolts step 1- 40 ft lbs
step 2- additional 90 degrees
recessed bolt 13 ftlbsaf151d2.gif

May 12, 2010 | 1998 Toyota Sienna

1 Answer

Engine head torque settings


2.0L 4 cylinder

cylinder head bolt torque

step 1 13-16 ft lbs.

step 2 additional 85 degrees

step 3 additinoal 85 degrees

2.5L V6

head bolt torque

step 1 17-19 ft lbs.

step 2 additinoal 85-95 degrees

step 3 additinoal 85-95 degrees

Mar 23, 2010 | 1998 Mazda 626

1 Answer

I nee the head bolt torque specs for a 95 sable


    • Tighten retaining bolts in sequence to 80 Nm (59 ft. lbs.).
    • Then back off bolts 360°.
CAUTION: Always use new cylinder head bolts when installing cylinder head or damage to engine may occur.
  1. Tighten the cylinder head retaining bolts in two final tightening steps in sequence shown in the following illustration:
    • 50 Nm (37 ft. lbs.)
    • 92 Nm (68 ft. lbs.)

Nov 03, 2009 | 1998 Ford Taurus

2 Answers

What is the torque specs for a 1998 jeep Cherokee classic straight 6 4.0 liter? I am replacing the head gasket and need to find the lbs of torque. Thank you for any advice, pictures, etc.


Torque sequence ------------------ front | 12 8 4 1 5 9 13 | of | | engine | 11 7 3 2 6 10 14 | ------------------ Final torque must be reached in 3 equal steps Step 1: torque all bolts (except bolt 11) to 110 Ft/Lbs Step 2: torque bolt 11 to 100 Ft/Lbs Recheck final torque in sequence.

  1. Disconnect the negative battery cable.
  2. Drain the cooling system.
  3. Disconnect the hoses at the thermostat housing.
  4. Properly relieve the fuel system pressure.
  5. Remove the cylinder head cover.
  6. Loosen the rocker arms.
  7. Remove the pushrods.

The valvetrain components must be replaced in their original positions.
  1. Remove the intake and exhaust manifold from the cylinder head.
  2. Disconnect the spark plug wires and remove the spark plugs.
  3. Disconnect the temperature sending unit wire, ignition coil and bracket assembly from the engine.
  4. Remove the accessory drive belt(s).
  5. Unbolt and set aside the power steering pump and bracket. Do not disconnect the hoses.
  6. Remove the intake and exhaust manifold assembly.
  7. If equipped with A/C, perform the following:
    1. Remove the compressor and position it aside with the lines attached.
    2. Remove the compressor bracket bolts from the cylinder head.
    3. Loosen the through bolt at the bottom of the bracket.

  8. Remove the alternator.
  9. Remove the cylinder head bolts, the cylinder head and gasket from the block.

Bolt No. 14 cannot be removed until the head is moved forward. Pull the bolt out as far as it will go and suspend in place by wrapping with tape.
  1. Discard the gasket. Thoroughly clean the head-to-block mating surface.
  2. Clean and inspect the cylinder head thoroughly. Refer to the engine reconditioning portion outlined later in this section.

To install:
  1. Coat a new head gasket with suitable sealing compound and place it on the block. Most replacement gaskets will have the word TOP stamped on them.

Apply sealing compound only to the cylinder head gasket. Do not allow sealing compound to enter the cylinder bore.

Oct 08, 2009 | 1998 Jeep Cherokee

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

176 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

75817 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

fordexpert

Level 3 Expert

5495 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...