Question about 1994 Toyota Pickup

1 Answer

My mechanic told me I need a new power steering pressure switch for my 1994 SR5 4WD V-6 xtra-cab pick-up. I cannot find one to order anywhere on the Internet. Does this part go by another name?

Posted by on


1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 10 achievements.


    An expert that got 5 achievements.


    An expert whose answer got voted for 500 times.

  • Master
  • 1,489 Answers

Here's a link to a site which sells "Power Steering Pressure Switches".


Posted on Mar 20, 2011

  • Samuel Charles Spriggs Mar 20, 2011

    I must ask why you didn't find this helpful ?




1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

My dad has a 1994 z71 extended cab and the ignition went out in it. I've been told I have to take the steering wheel off but I don't know where to go from there. How do I change the ignition switch...

yes you have to take the steering wheel off, next you will need to take off the round pressure plate that is secured with a C pin around the inner column(behind the plate is a big spring, remove). after that you will need to remove the plastic switches behind the pressure plate. there is a screw on the right that holds in the ignition. after removing the screw the ignition should come right on out. put in the new ignition and make sure to fasten the screw back on. replace the plastic switches and put on the pressure plate (which is very hard to do and remember to fasten it back on with the tiny C clip and make sure that your spring is BEHIND the plate) then bolt back on your steering wheel

Nov 29, 2011 | 1994 Chevrolet K1500

1 Answer

How to replace high pressure hose on a 1994 Silverado Chevrolet pick up truck.

hmmm..which high pressure hose the a/c or power steering hose...if its the a/c u need to take this to a service center. removing the high pressure hose without recovering the freon can cause serious is under extreme high pressure at all times even when the truck is not running... if its the power steering hose then start by removing the plastic shield in the steering staft at the steering box on the drivers side frame loosen the 18mm line nut then follow it to the other line nut on the back of the power steering pump....but sometimes the pump may need to be removed to to this, if this is the case i recommend u take it to a service center

Jul 12, 2011 | Chevrolet Silverado Cars & Trucks

1 Answer


1. Remove serpentine belt

2. loosen power steering pressure and return hoses

3. Remove nut from pressure line mounting on alternator bracket

4. remove power steering pump mounting bolts.

5. Lift pump assembly from engine mounting and remove hoses.

6. Reverse order to install. Fill and bleed system.

NOTE: A new or rebuilt power steering pump will most likely not come with a pulley attached. You will need a power steering pulley remover/installer tool to transfer the pully from the old pump to the new one.

Feb 19, 2011 | Chevrolet Malibu Cars & Trucks

1 Answer

I just purchased a 1989 chevy cheyenne but was told the turn signal does not work. I was told it was a switch in the steering column...Is that fairly easy to get to and fix?

To perform this repair you need to remove the steering wheel. there will then bee two or three screws holding the mechanism in place. down towards the bottom of your steering column you will find the wiring that you needs to disconnect. Pull the wiring up and out and install the new signal switch in reverse order.

Jan 24, 2011 | Chevrolet Chevy Cars & Trucks

1 Answer

Vacuum switch on power steering pump?!?!? What does it do??

Your mechanics are either stupid or are playing stupid. Its to raise the idle speed when there is high power steering pressure. Like when you turn the steering wheel, the pressure goes up, and it raises the engine idle speed. Find one in a junkyard, They have U-Pull IT yards around here, you can get one cheap.

Mar 13, 2010 | 1990 Toyota Pickup

1 Answer

1992 toyota pick up extra cab, extra long deluxe... what should the tire pressure be?

The Manufacturer's recommended tire size and inflation decal should be in the door jamb below the latching mechanism on the driver's side door, but if it is not there, 29-30psi front 32-34psi rear. You can go with 32psi at all four corners. That is the pressure i run in my '85 Xtra Cab DLX and it works great.

Hope this helps,

Oct 08, 2009 | 1992 Toyota Pickup

1 Answer

Where is the power steering sensor located on a 1993 ford ranger 4.0 super cab? (or is it called the power steering pressure switch?)

The power steering pressure switch as its called threads in to the power steering pressure hose most of the time it is close to the power steering pump, I have also seen them at the lower point of the pressure hose close to the rack and pinion.

Nov 25, 2008 | 1993 Ford Ranger SuperCab

Not finding what you are looking for?
1994 Toyota Pickup Logo

Related Topics:

185 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts


Level 3 Expert

80263 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8841 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides