Question about 1999 Land Rover Discovery

1 Answer

Wiring diagram for spotlights on a discovery I/II (1999) Would like to mount and wire the spotlights up so as they come on highbeam only, and would like to connect it into the ' rear fog light ' switch. is this possible?

Posted by on

×

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 3,400 Answers

You can find factory wiring diagrams here (free RAVE Download) http://www.landroverresource.com/ And sure you can wire your spots into rear fog switch, depending on watts/draw of your lights you might want to "UP" the fuse rating

Posted on Mar 20, 2011

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Which colour is the highbeam wire on a 2003 santa fe.


Get your meter out and find out which wire gets voltage when the high beams are on.
Much easier than trying to find schematics.

Sep 14, 2014 | 2003 Hyundai Santa Fe

1 Answer

Spotlight wiring in landcruiser


I would just tie into the high beam wiring at the factory lights, wire them into a relay and go from there. I wouldn't even consider adding into the high beam system without a relay. You may also want to consider a switch so you can shut them off if you found yourself in a position where you want your factory highbeams but not the extra's. Good luck and have fun :)

Nov 05, 2013 | Cars & Trucks

1 Answer

Find highbeam hotwire for connection to relay for spotlights


You would be better off to run wires to the battery , put in a fuse, and put in a switch for these. Depending on the year. Switches, relays,wiring, and fuses in the newer years can not carry this extra type of load. They will eventually burn out.

Feb 24, 2011 | Suzuki Grand Vitara Cars & Trucks

1 Answer

1999 Land Rover Discovery II engine miss


Observe the engine running in the dark to see if there are any spark jumps from the wires or coil, you may have a carbon track.....

Feb 16, 2010 | 2001 Land Rover Discovery Series II

1 Answer

Roof mounted spotlights


You can run the power wire into the cab to a universal
toggle switch. Then run a wire from the other side of the switch to the + side of your second battery.
Ground the light at the mounting point. Be sure to use a 20amp circuit breaker toggle switch, or splice in an inline fuse holder with a 20amp fuse, on the +
side. Hope this helps. Good luck.

Feb 07, 2010 | 1999 Toyota Land Cruiser

1 Answer

I have a 1999 DII and have just replaced the auto dim mirror with a new style with compass, how do I remove the old mirror


The mirror can be removed by carfully pulling down towards the dash.
unplug the wiring block and re install the new mirror. In my case the wiring block was a miss match so I cut the wires and used generic connectors to reconnect the power.

Sep 30, 2009 | 2001 Land Rover Discovery Series II

1 Answer

Discovery II 1999,


It's located on the lower section of the engine block, left hand/drivers side. You'll see some wires going to it, and a round heat shield covering the sensor itself if the shield is still there. You have to remove the heat shield to access the fasteners holding the sensor to the 2 studs of the mounting bracket. The connector for the sensor is up higher on the engine, behind the drivers/left cylinder head. Not easy to get to.

Jun 05, 2009 | 1999 Land Rover Discovery

1 Answer

Transfer case oil change- 1999 Land Rover Discovery II


No need for a diagram, to drain the oil, there's a drain plug on the bottom of the transfer box, under the handbrake drum. To fill, the fill plug is about in line with the centre of the handbrake drum and to the left. I think both plugs are 1/2" square. Fill to overflow with Texaco Multi-Gear 75W/90R. Takes about 2L or so.

Mar 29, 2009 | 1999 Land Rover Discovery

2 Answers

Land Rover Discovery 2 Spark plug diagram needed.


This is your best choice.Here is a diagram attached.023c4c3.jpg

Dec 10, 2008 | 1999 Land Rover Discovery

Not finding what you are looking for?
1999 Land Rover Discovery Logo

1,086 people viewed this question

Ask a Question

Usually answered in minutes!

Top Land Rover Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

yadayada
yadayada

Level 3 Expert

75051 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7727 Answers

Are you a Land Rover Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...