Question about Ford Expedition

1 Answer

A bit of knocks and jolts caused by transmission. Local Ford service center says its the transfer case. Can this be repaired, or the whole assembly replaced. The unit is a 1999 Ford XP bought in the Philippines. thanks!

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Ford Master
  • 14,036 Answers

TRANSFER CASE CAN BE REPAIRED BUT IT WILL CHEAPER TO TRADE OLD UNIT FOR A REBUILD ONE.BECAUSE YOU HAVE TO BE HIGHLY SKILLED TO FIX TRANSFER CASE.YOU HAVE MANY SMALL PARTS.AND NUMEROUS CLEARANCES MUST BE PRECISELY MEASURED CORRECTLY LIKE SPACERS AND SNAP RINGS.YOU NEED TOOLS TO DO OVER HAUL.SAYING THIS WOULD BE CHEAPER TRADE IN TRANSFER CASE FOR A REBUILT ONE OR TAKE THE OLD TRANSFER CASE TO A TRANSMISSION SHOP HAVE THEM OVER HAUL IT.GOING COST EITHER WAY.IF REMOVE TRANSFERCASE YOUR SELF PROBABLY SAVE YOU $400.00 LABOR CHARGE TAKE 3 TO 4 HRS TO REMOVE TRANSFER CASE.

Posted on Mar 20, 2011

  • Jonah Oneal Mar 20, 2011

    TRANSFER DRIVE CHAIN HAS A LOT OF SLACK OR DRIVE SPROCKET TEETH WORN OR MISSING TEETH OR REAR OUT PUT SHAFT HAS WORN BUSHING AND WORN OR MISSING NEEDLE BEARINGS. IF YOU WANT TO OVER HAUL IT YOUR SELF. I CAN GIVE YOU A LIST OF THINGS YOU WILL NEED.YOU NEED REPAIR MANUAL FOR THE EXACT TRANSFER CASE YOU WORKING ON.YOU CAN GO ON LINE INTERNET FIND ONE. TOOLS YOU NEED WILL BE INTERNAL AND EXTERNAL SNAP RING PLIERS, NEED BEARING PULLER,NEED SLIDE HAMMER,NEED SET OF PIN PUNCHES,A DIAL INDICATOR,NEED A HYDRALIC PRESS, YOU NEED TORQUE WRENCHES , NEED STURDY WORK TABLE WITH A VISE. AND NEED TRANSFER CASE STAND.

×

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Im getting ready to pull the transmission out of my 95 isuzu trooper with the 3.2l engine 4x4. Im not to smart about the inside of them, does the 4L30e have tranny bolts th hold the housing to tranny


why not login in to mitchell DIY, (goggle it ) and read.
or go to any online, 4L30 parts house and read.
lots of those, can all found easy using "GOOGLE"
here.
search, (4L30 parts)
3rd hit MAKCO
see the graphic there, click it.

http://www.makcotransmissionparts.com/4L30E.html

you need to remove the TC, bolts first
the bell housings bolts to the engine,
those come off, with tranny jack in place.
all the steps are in the service manual.
4wd.
quote (a wall of text, why not buy the book?)

& Transfer Case Automatic Transmission Transmission Removal 4L30-E Transmission

4L30-E Transmission(removal

Print
4L30-E Transmission
Disengage the oxygen sensor connector from the transmission wiring harness connector

Disengage the oxygen sensor connector from the transmission wiring harness connector
Detach the selector lever end of the shift lock cable from the lever assembly by loosening the adjusting nuts and sliding the end out of the bracket

Detach the selector lever end of the shift lock cable from the lever assembly by loosening the adjusting nuts and sliding the end out of the bracket

Disconnect the shift control rod from the selector lever lower lever arm

Disconnect the shift control rod from the selector lever lower lever arm

Remove the oil pipe clamp bracket from the engine stiffener

Remove the oil pipe clamp bracket from the engine stiffener
Make certain to tighten the transmission-to-engine mounting bolts to the proper amount of torque-the torque measurements are shown in parentheses

Make certain to tighten the transmission-to-engine mounting bolts to the proper amount of torque-the torque measurements are shown in parentheses


NOTE

The transfer case is an integral part of the transmission housing. Although the 2 cases can be separated, the transfer case should be removed with the transmission.

Use a felt-tipped marker to matchmark the hood to the hood hinges. Remove the hood.

Disconnect the negative battery cable.

Shift the transmission into the N position, and the transfer case into the 2H position.

Remove the air cleaner assembly.

Remove the transfer case shift knob. Remove the 4 transmission cover console retaining screws.

Remove the center console assembly and disengage the console switch wiring connectors.

Disconnect the shift lock cable and the shift control rod from the selector lever assembly.

Unbolt and remove the transfer case control lever.

Raise and safely support the vehicle on jackstands.

Remove the transmission and transfer case skid plates.

Remove the exhaust pipe protectors.

Drain the transmission fluid. For more information servicing the transmission fluid pan and filter, refer to Section 1.

Label and detach the oxygen sensor connectors.

Remove the catalytic converter, center exhaust pipe and front exhaust pipe, as described in Section 3.

Matchmark the front and rear driveshafts to the differential and transfer case flanges.

Unbolt and remove the front and rear driveshafts, as described later in this section.

Disconnect the oil cooler lines from the transmission. Plug the lines to prevent fluid loss and contamination.

Remove the brackets securing the oil cooler lines to the engine stiffener.

Remove the front suspension crossmember.

Remove the dipstick and tube. Disconnect the breather hoses from the tube.

Remove the 5 engine stiffener bracket bolts and the stiffener bracket.

Remove the heat protector.

Disengage the transmission harness connectors and the mode switch harness connector from the engine harness.

Disconnect the harness clamp from the clamp bracket.

Disconnect the ground cable from the engine.

Remove the starter motor, as described in Section 2.

Remove the flexplate inspection cover.

Remove the 3 bolts securing the flexplate to the torque converter. Turn the crankshaft to gain access to all 3 bolts.

NOTE

Remove the radiator upper fan shroud and the cooling fan to access the crankshaft center bolt to turn the crankshaft.

Place a suitable transmission jack under the transmission and transfer case unit for support.

Raise the transmission slightly and remove the 8 bolts securing the rear mount and the transmission crossmember.

NOTE

Make sure the engine and transmission assembly is properly supported before removing the rear mount and third crossmember.

Raise the engine slightly with an engine hoist and remove the transmission-to-engine bolts.

Separate the transmission from the engine and lower the transmission from the vehicle.
end removal quote

Mar 04, 2017 | Isuzu Trooper Cars & Trucks

1 Answer

When I shift manual shifter from 4 wheel drive back to 2 wheel drive, truck does not want to return to 2 wheel drive. Dash light goes off as expected. No service light comes on. I did put truck in reverse...


Just to confirm, you don't have an electrical 4WD selector; you have to move a shifter on the floor of our cab? If that's the case, I'd suspect that you have a linkage misalignment or malfunction that doesn't allow the 4WD selector to completely return to the 2WD position. Putting the truck into reverse and back to drive probably causes a jolt to the 4WD linkage which disengages the transfer case from the driveline. Check for slack or binding in the transfer case shift level linkage (clean and lube the linkage won't hurt).

Oct 03, 2013 | 2006 GMC Sierra

1 Answer

2002 f150 4wd drive not not working,


Transfer Case - Electronic Shift on the Fly (ESOF) Features A rotary switch allows the vehicle operator to choose between 2WD, 4H, and 4L modes of 4x4 operation.
The generic electronic module (GEM) controls the operation of the 4x4 system.
The output shaft speed (OSS), mounted in the rear of the transfer case, informs the GEM of the vehicle speed.
The shift motor sense plate, an integral part of the electronic shift motor, informs the GEM to the positions of the transfer case (go to Table 4).
The transmission range sensor is located on the LH side of the transmission; this sensor informs the GEM when the transmission is in the NEUTRAL position.
The electronic shift motor, mounted externally at the rear of the transfer case, drives a rotary cam which moves the mode fork and range fork within the transfer case to select between the 2WD, 4H, and 4L positions.
The 4x4/4x2 vacuum solenoids are attached to the upper RH side of the engine compartment, and alternately route vacuum to the vacuum motor which engages/disengages the center axle disconnect collar in the front axle assembly.
The 4x4 shift motor relay is a module containing two relays. Under the control of the GEM, the 4x4 shift motor relay shifts the transfer case shift motor between the 2WD, 4H, and 4L modes.
The transfer case clutch relay is an electromechanical relay used to activate the transfer case clutch within the transfer case.


Your best bet , take it to a qualified repair shop !

P1804 Transmission 4-Wheel Drive High Indicator Circuit Failure GEM REFER to Section 413-01A . P1806 Transmission 4-Wheel Drive High Indicator Short Circuit to Battery GEM REFER to Section 413-01A . P1812 Transmission 4-Wheel Drive Mode Select Circuit Failure GEM REFER to the Symptom Chart. P1815 Transmission 4-Wheel Drive Mode Select Short Circuit to Ground GEM REFER to the Symptom Chart. P1820 Transmission Transfer Case Clockwise Shift Relay Coil Circuit Failure GEM GO to Pinpoint Test A . P1822 Transmission Transfer Case Clockwise Shift Relay Coil Short Circuit to Battery GEM GO to Pinpoint Test A . P1824 Transmission 4-Wheel Drive Clutch Relay Circuit Failure GEM GO to Pinpoint Test E . P1826 Transmission 4-Wheel Drive Low Clutch Relay Short Circuit to Battery GEM GO to Pinpoint Test E . P1828 Transmission Transfer Case Counter Clockwise Shift Relay Coil Circuit Failure GEM GO to Pinpoint Test A . P1830 Transmission Transfer Case Counter Clockwise Shift Relay Coil Short Circuit to Battery GEM GO to Pinpoint Test A . P1832 Transmission Transfer Case Differential Lock-Up Solenoid Circuit Failure GEM GO to Pinpoint Test C . P1834 Transmission Transfer Case Differential Lock-Up Solenoid Short Circuit to Battery GEM GO to Pinpoint Test C . P1838 Transmission Transfer Case Shift Motor Circuit Failure GEM REFER to the Symptom Chart. P1846 Transmission Transfer Case Contact Plate 'A' Circuit Failure GEM REFER to the Symptom Chart. P1850 Transmission Transfer Case Contact Plate 'B' Circuit Failure GEM REFER to the Symptom Chart. P1854 Transmission Transfer Case Contact Plate 'C' Circuit Failure GEM REFER to the Symptom Chart. P1858 Transmission Transfer Case Contact Plate 'D' Circuit Failure GEM REFER to the Symptom Chart. P1866 Transmission Transfer Case System Concern - Servicing Required GEM REFER to the Symptom Chart. P1867 Transmission Transfer Case Contact Plate General Circuit Failure GEM REFER to the Symptom Chart. P1876 Transmission Transfer Case 2-Wheel Drive Solenoid Circuit Failure GEM GO to Pinpoint Test C . P1877 Transmission Transfer Case 2-Wheel Drive Solenoid Circuit Short to Battery GEM GO to Pinpoint Test C . P1891 Transmission Transfer Case Contact Plate Ground Return Open Circuit GEM REFER to the Symptom Chart.

Nov 26, 2017 | 2003 Ford F150 Regular Cab

2 Answers

2002 yukon front end wont engage


2002 GMC Yukon

2002 GMC Yukon

2004 TRANSMISSION Transfer Case - NVG 149-NP (One Speed Automatic) - SUV

2004 TRANSMISSION Transfer Case - NVG 149-NP (One Speed Automatic) - SUV

TRANSFER CASE NO FRONT DRIVE

Transfer Case No Front Drive

Cause

Correction

DEFINITION: The transfer case is not delivering engine torque to the front propeller shaft.

Review the Symptoms - Transfer Case and perform the necessary inspections.

Viscous coupling faulty 1. Inspect the transfer case fluid for being black. If the fluid is

black, it is most likely caused by a viscous coupling failure.

2. Test for a faulty viscous coupling. Refer to Transfer Case

Description and Operation.

3. Disassemble the transfer case. Refer to Transfer Case

Disassemble in Transfer Case - NVG 149-NP3 Unit Repair.

4. Inspect the viscous coupling for a bulged cover. Refer to

Cleaning and Inspection in Transfer Case - NVG 149-NP3 Unit

Repair.

5. Replace the viscous coupling if it is faulty. Refer to Transfer

Case Assemble in Transfer Case - NVG 149-NP3 Unit Repair.

Planetary carrier faulty 1. Disassemble the transfer case. Refer to Transfer Case

Disassemble in Transfer Case - NVG 149-NP3 Unit Repair.

2. Inspect for faulty planetary carrier components. Refer to

Cleaning and Inspection in Transfer Case - NVG 149-NP3 Unit

Repair.

3. Replace any faulty planetary carrier components. Refer to

Transfer Case Assemble in Transfer Case - NVG 149-NP3 Unit

Repair.

Oct 19, 2010 | GMC Yukon Cars & Trucks

1 Answer

What is transmission assembly and transfer case, i just know i need a transmission but keep finding these words


the transmission assembly is the collection of gears etc enclosed in a casing called the gearbox,although in an autobox it is correctly called "a transmission assembly".The transfer case is the box between the gearbox and the engine that encloses the torque converter,any wiser???

May 04, 2010 | 1998 Ford Escort

3 Answers

Front seal leak in transmission on a 2001 ford expedition


Find the exact location of your leak to determine the cost for repairs. If centered between the trans and engine the trans has to be removed. If the pan is leaking just the pan has to be removed

Jan 24, 2010 | 2001 Ford Expedition

1 Answer

Transmission fluid leaking back, 1988 Ford Bronco


your output seal on the tranny or input seal on your transfer case is bad. you have to pull your transfer case to tell. this is a pretty straight forward job. block wheels. put transfer case in neutral. drop front and rear drive lines.diconnect transfer case shift linkage. there is a short commponent connecting the trans to the transfer case. the bolt on either end face each other. remove the bolts to the transmission. the transfer case is heavier than it looks, i suggest getting help. pull back on the transfer case until it will drop down. it will pull out a bit because of the trans output shaft. replace what will probibly turn out to be the tranny output shaft seal and reassemble in reverse order.

Nov 06, 2009 | 1988 Ford Bronco II

1 Answer

Causing a loud sound in back is that part of the transmission if so should when taking out the transmission that you have to take out the transfer case as while all at the same time .


you have to unbolt the transfer case from the trannsmission, or u can take it out in one peice just a bit harder. you might have bad u-joints thats causing the loud noise, like clunks.

Nov 02, 2009 | 2003 Ford Explorer Sport

1 Answer

2005 Ford Explorer XLT


transmission need to fix

Sep 14, 2008 | 2005 Ford Explorer

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

205 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

79865 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

fordexpert

Level 3 Expert

5687 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...