Question about 1988 GMC K2500

1 Answer

My truck wouldnt move so i looked at the torque converter while it was running and it is barley moving. how do i fix it?

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

I was at stop sign i move little bit my truck stop moving and truck was running.. i try to put it in drive wont move i also tryed other gears wont move at all. any one help me out?

Posted on Jan 06, 2013

Ad

5 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get to try the service completely Free afterwhich it costs $6 per call and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
Pattods
  • 116 Answers

SOURCE: i believe my torque converter is out in my oldmobile

Well to replace the TC, you have to unbolt the transmissions bell housing from the rear of the engine. Then, it's rather simple from there on in. I'd suggest a full manual for the car so you could know what you're looking at.

Either way, without a good selection of tools, and the right spot to work on it, it's probably better just to have a mechanic look at it.

As for the TC actually going out, it's not highly likely that it would. You may just have a really clogged fluid filter and be in desperate need of a transmission flush/change. Also, the valves may be bad as well, which still isn't much of a hassle to replace if you know what you're doing. I've seen hundreds of automatic transmissions go out in my life, but only a few have ever been a direct result of the TC.

Posted on Sep 25, 2008

  • 84 Answers

SOURCE: Transmission repairs

It sounds as if there is no oil pressure in the transmission, it is possible you have no fitted the convertor correctly. if it is not fully engaged into the transmission oil pump it will not drive. of course the other thing could be the transmission has a fault. I am of course assuming you have filled the transmission with the correct type and quantity of oil. if you have pull the trans, and check the convertor has not damaged the oil pump,

Posted on Jan 22, 2009

  • 1 Answer

SOURCE: lost drive in auto gearbox

Does it move but the speedo doesnt work properly or at all? Unusual or no gear changes? Suspect the Vehicles Speed Sensor (VSS) on the gearbox.

If it doesnt move in any gear check the autobox fluid level, failing that get it checked for copdes, could be a few things

Posted on Jan 25, 2009

  • 1 Answer

SOURCE: 1998 isuzu trooper torque on demand lights go off

It is Torque On Demand. When you are stopped there is no need for the front end to be engaged, no demand. Once you start moving, the lights should begin working as the demand for four wheel drive engagement increases, if the conditions require four wheel drive. It's the way the system works. Enjoy!

Posted on Sep 11, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Will not move in any gear and also wouldnt work in forward or reverse


If its automatic. Torque converter consists of 3 components. Impeller(bowl like dome with fins inside it for fluid displacement), turbine(same as above), stator(located in the centre; like a fans blades). Fluid flows and reaches optimal flow to give drive to the wheels. If there is no fluid, then there is no drive. Check gearbox fluid level. Or maybe the gearbox broke, or the diff broke or a cv shaft or a cv joint.

Dec 07, 2014 | Cars & Trucks

1 Answer

Transmission


u will find that your gearbox is about to let go if it was your torque converter then your car wouldnt move

Mar 11, 2014 | 2000 Dodge Caravan

1 Answer

Torque converter clutch stuck on


The torque converter clutch solenoid is controlled by the TCM so run the fault codes first/. If you take the solenoid out of the system there is every possibility that the vehicle will not move and if it does the economy will be crap. Best fix the thing properly to start with.

Feb 17, 2014 | Ford Ranger Cars & Trucks

1 Answer

Accleration


Trans torque converter make sure fluid is good when Trans is hot and fill when running if low. If doesn't fix sorry but replace torque converter

Feb 16, 2014 | 1998 Buick Park Avenue

1 Answer

Torque converter making noise


drop off the cover under the torque converter and inspect the flex plate that the converter is bolted to. look for cracks in the plate around the bolts . undo the bolts and move the torque converter back towards the gear box and look for cracks around the flywheel bolts.. If all ok then do everything up and have a pressure test done on the transmission to check for internal mechanical failure. Have this done at an accredited auto transmission shop ( not the local mechanic) and as him what the results are and the possible solution. Remember to ask how much to fix the problem parts before you accept that it needs a new box

Jan 11, 2014 | 2004 Lincoln LS V8

1 Answer

Car starts ok been stood for ten days and wont move stook to floor


run the fault codes and look for TCM problem check for torque converter clutch solenoid fault.

Dec 29, 2013 | 2008 Nissan Micra 1.2

1 Answer

What is the transmission model of a 2001 4WD Isuzu Fuego. Its not responding to drive and reverse anymore. We think that its best to look for a surplus transmission while we figure out a temporary solution...


run fault codes and look for a faulty TCM unit. IT controls the torque converter clutch which may be where the problem lies as if the torque converter servo is not working then you will have no input into the transmission.

Oct 30, 2013 | Isuzu Cars & Trucks

1 Answer

Started make a whinning sound i pulled over then it would not move. 2002 84,000 miles and was not acting funny before


Hi and welcome to FixYa!

If the engine works but won't move then the problem will be on the transmission. Looks like you have a faulty torque converter. If the torque converter is faulty the car will not shift properly or won't move at all. I strongly suggest that you replace the torque converter and transmission fluid.

Hope this information was helpful enough and thank you for using FixYa! Have a good one!

Feb 01, 2011 | 2002 Chrysler 300M

1 Answer

Ford 2003 Windstar transmission problem


Windstar tranny problem: just got off phone with Northway Transmission of Queensbury, NY Technician said the torque converter had destroyed itself. the pump drive spline in converter broke and took out fins in torque converter it's going to cost me nearly $1600.00 car has only 45000mi on it and I caught it rather quickly and DID NOT TOW had car moved by flatbed/ramp truck otherwise they would have had to completly tear down transmission. (over $2300.00)

Jan 03, 2009 | 2003 Ford Windstar

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

73 people viewed this question

Ask a Question

Usually answered in minutes!

Top GMC Experts

yadayada
yadayada

Level 3 Expert

76630 Answers

Freddy

Level 3 Expert

1311 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Are you a GMC Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...