Question about 2002 Toyota Land Cruiser

Open Question

Spark plug replacement on 90 series prado 3400, where can I find a diagram of the engine and spark plug sequence?

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Richie_asg1
  • 1036 Answers

SOURCE: 1992 Isuzu Rodeo Distributor wires 3.1L engine

Hi,
Isuzu seem to have complicated things by changing engines, firing orders and even direction of rotation! As you can see, they've numbered the cylinders the other way than the 3.2L.

The Firing sequence for the 3.1 (traditional distributor) 6 cylinder is as follows -

d6e5b2a.jpg

If you take the distributor cap off, there should be a "No.1" formed on the inside. Stick a lead on this before you put the cap back on and go from there.
As leads are different lengths, you may have to swap a few to find the best fit.

I think 2 of them will look out of place - but that's the way it's designed. Just make use of clips for holding them neatly.

Thanks for using Fixya.









Posted on Jul 06, 2008

  • 28 Answers

SOURCE: Spark plug seal replacement

toyota genuine part number is 11193-70010 6pcs for your car you have to buy and open the cylinder head cover and replace all the gaskets on right and left side

Posted on Jul 17, 2008

SOURCE: Cannot locate the spark plugs in the 2004 Kia Sedona engine

First you have to take off the black plastic cover then you will see the 3 on the front of the engine the other 3 are under the manifold, you have to remove the manifold in order to reach them, I suggest you take the car to a mechanic for this work.

Posted on Sep 13, 2008

  • 65 Answers

SOURCE: spark plug replacement

The recommended milage is 60k miles for the plugs.I wouldn't wory about anything else except.Keep a clean air filter change the oil when required and check the trans fluid as it likes to discolor easy.So a simple drain and refill often helps.It is like a oil change they have a drain plug on the pan (very nice).It takes about four quarts of fluid and the dipstick will tell you what type of fuid to use it is stamped on the metal by the level marks.Good luck Thanks for using Fix Ya

Posted on Nov 29, 2008

  • 462 Answers

SOURCE: need a diagram of the firing order of spark plug wires from coil packs to spark plugs

FROM LEFT TO RIGHT, 5/2 3/6 4/1. ASSUMING YOU HAVE THE 3.1L ENGINE.

Posted on May 31, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My 2004lmpala wont start 3400 engine ?


If it cranks good but won't start, have a helper crank it while you visually check for spark at the spark plugs. If spark everywhere, use a gage and check proper fuel pressure. Also check for fuel injector pulse.

What lights, are you talking about dash lights? If so, some of those items may not go hot until you turn on the key. Then I would check ignition switch and wiring. I haven't looked at your wiring diagrams. I would think the horn circuit would be hot all the time.

Nov 05, 2015 | Cars & Trucks

1 Answer

Engine diagram 3400 v6


Check the ignition wires and distributor cap. The spark is probably jumping to the wrong plug. Worn insulation where two wires cross, or a dusty/cracked cap can cause this.

Apr 28, 2014 | 1995 Pontiac Firebird

1 Answer

Pontiac 3400 misfire problem one new coil pack new plugs and wires on still running bad have too press gas too start now bad fuel mileage unburnt fuel smoke when engine starts for a few seconds then stops...


some of the cylinder wont get spark, faulty spark plug, wire or coil. To check pull all spark plugs out, plug them to the wires and put on the engine top and then cranck the engine to see which spark plug not giving a spark

Apr 16, 2014 | Cars & Trucks

1 Answer

Looking for head bolt troque spec for 3.4l impala sfi04


Please don't forget to rate. Thank you:

Left side front cylinder head


98e175a.gif
Cylinder head bolt torque sequence-3.4L engine

  • Cylinder head by aligning it with the dowel pins
  • New cylinder head bolts coated with a sealant (such as GM 1052080). Torque the bolts in the proper sequence (1-8) to 37 ft. lbs. (50 Nm). Using a torque angle meter turn the bolts 90 degrees in the proper sequence.
  • Left side exhaust manifold. Torque the bolts to 12 ft. lbs. (16 Nm).
  • Spark plugs. Torque the plugs 11 ft. lbs. (15 Nm).


  • Right side rear cylinder head:


    71cd5b7.gif
    Cylinder head bolt torque sequence-3.4L engine


  • New cylinder head gasket
  • Cylinder head on top of the gasket and make certain it is lined up properly with the dowel pins
  • New cylinder head bolts coated with a sealant (such as GM 1052080). Torque the bolts in the proper sequence (1-8) to 37 ft. lbs. (50 Nm). Using a torque angle meter turn the bolts 90 degrees in the proper sequence.
  • Right side exhaust manifold. Torque the bolts to 12 ft. lbs. (16 Nm).
  • Spark plugs. Torque the plugs 11 ft. lbs. (15 Nm).
  • Spark plug wires
  • Exhaust crossover pipe. Torque the fastener to 18 ft. lbs. (25 Nm).
  • Valve rocker arms and pushrods. Torque the fastener to 89 inch lbs. (10 Nm). Using a torque angle meter torque the fastener an additional 30 degrees.
  • Lower intake manifold. Torque the bolts to 115 inch lbs. (13 Nm).
  • Upper intake manifold. Torque the bolts to 18 ft. lbs. (25 Nm).
  • Nov 26, 2010 | 2004 Chevrolet Impala

    3 Answers

    2000 Grand Am GT: I need the firing order diagram for a 2000 pontiac...


    2000 Pontiac Grand AM 3.4 liter V-6 VIN "E"

    f8fdb07.gif

    Hope helps (remember rated this).

    May 17, 2010 | 2000 Pontiac Grand Am GT

    2 Answers

    Head gasket torque specifications and sequense


    Please don't forget to rate. Thank you:

    Left side front cylinder head


    98e175a.gif
    Cylinder head bolt torque sequence—3.4L engine

  • Cylinder head by aligning it with the dowel pins
  • New cylinder head bolts coated with a sealant (such as GM 1052080). Torque the bolts in the proper sequence (1-8) to 37 ft. lbs. (50 Nm). Using a torque angle meter turn the bolts 90 degrees in the proper sequence.
  • Left side exhaust manifold. Torque the bolts to 12 ft. lbs. (16 Nm).
  • Spark plugs. Torque the plugs 11 ft. lbs. (15 Nm).


  • Right side rear cylinder head:


    71cd5b7.gif
    Cylinder head bolt torque sequence—3.4L engine


  • New cylinder head gasket
  • Cylinder head on top of the gasket and make certain it is lined up properly with the dowel pins
  • New cylinder head bolts coated with a sealant (such as GM 1052080). Torque the bolts in the proper sequence (1-8) to 37 ft. lbs. (50 Nm). Using a torque angle meter turn the bolts 90 degrees in the proper sequence.
  • Right side exhaust manifold. Torque the bolts to 12 ft. lbs. (16 Nm).
  • Spark plugs. Torque the plugs 11 ft. lbs. (15 Nm).
  • Spark plug wires
  • Exhaust crossover pipe. Torque the fastener to 18 ft. lbs. (25 Nm).
  • Valve rocker arms and pushrods. Torque the fastener to 89 inch lbs. (10 Nm). Using a torque angle meter torque the fastener an additional 30 degrees.
  • Lower intake manifold. Torque the bolts to 115 inch lbs. (13 Nm).
  • Upper intake manifold. Torque the bolts to 18 ft. lbs. (25 Nm).
  • Mar 06, 2010 | 2001 Chevrolet Venture

    1 Answer

    How to change spark plugs on 1997 ford ranger


    Changing the spark plugs is a pretty easy task. The spark plugs run along both sides of the engine (if its a V block) , 1 per cylinder. You can easily identify them by the plug wires running to them from the distributor. Pop off each plug wire, (1 at a time) and replace the spark plug. Once you have replaced the plug, replace the plug wire. This ensures that you dont mess up the sequence of the wires which determines which cylinder fires at what time in the cycle. VERY important not to mess up the sequence. If you should happen to get the wires mixed up, look online for the firing sequence for your vehicle and engine.

    Jan 03, 2010 | 1997 Ford Ranger SuperCab

    1 Answer

    Plugs


    Changing the spark plugs is a pretty easy task. The spark plugs run along both sides of the engine, 1 per cylinder. (3 on each side) You can easily identify them by the plug wires running to them from the distributor. Pop off each plug wire, (1 at a time) and replace the spark plug. Once you have replaced the plug, replace the plug wire. This ensures that you dont mess up the sequence of the wires which determines which cylinder fires at what time in the cycle. VERY important not to mess up the sequence. If you should happen to get the wires mixed up, look online for the firing sequence for your vehicle and engine.

    Dec 30, 2009 | 2006 Toyota Tacoma

    1 Answer

    Need spark plug wiring sequence, 1985 toyota corolla 1600 2 door hatchback, rear wheel drive


    With the 2T-C, 3T-C, and 3K-C engines the Firing Order is 1-3-4-2
    The distributor rotates ->Clockwise. (The rotor actually)

    Number 1 spark plug tower on the distributor cap, faces directly towards the engine. Number 2 faces the back of the engine, Number 4 faces the front of the engine, Number 3 is to the outside away from the engine.

    Number 1 spark plug is at the front of the engine. 1-2-3-4

    With the 4A-C engine, and other A-Series, the Firing Order is 1-3-4-2
    The distributor rotates ->CounterClockwise.

    Number 1 spark plug tower is towards the engine, and faces the back of the engine. Number 3 spark plug tower is away from the engine, and faces the back of the engine.
    Number 2 spark plug tower is towards the engine, and faces the front.
    Number 3 spark plug tower is away from the engine, and faces the front.

    Aug 16, 2009 | 1985 Toyota Corolla 2 Door

    Not finding what you are looking for?
    2002 Toyota Land Cruiser Logo

    Related Topics:

    270 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Toyota Experts

    yadayada
    yadayada

    Level 3 Expert

    75117 Answers

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    22095 Answers

    Jeff Turcotte
    Jeff Turcotte

    Level 3 Expert

    7772 Answers

    Are you a Toyota Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...