Question about 1995 Chrysler LeBaron

1 Answer

I just had a new windshield put in my 1995 chrysler convertible and when I put the topp it won'close all the way. Is there some way to adjust it so that I can latch it down

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Brigadier General:

    An expert that has over 10,000 points.

  • Master
  • 3,513 Answers

Hi

Stop the car and shift it into "Park." Turn the ignition key to the "On" position. Open both latch handles. There is one on each side of the windshield at the top of the frame. The latch handle will flip open, toward the door.

Press the "Power Top Switch." Hold the switch while the top comes up. Release the switch once the top reaches the top of the windshield frame.

Pull the top down toward the windshield frame by grasping the handle in the center of the top. Hold the top while you flip the latch handle toward the center of the windshield to secure the top. Repeat the process with the latch handle on the other side.

However if it won't go down then this can be caused by your trunk lid not being all the way shut. Also its possible the motor on the hydraulic pump has failed, you will have to check for power at the motor while pressing the switch, if you have it, replace the motor.


Please get back to us if you have further query else please accept the suggestion.

Posted on Mar 21, 2011

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Ok i put my new brake switch in and now my shifter lever won't shift does anyone know why it won't shift


you may have to adjust your switch might be in the hole too far, or defective

Nov 29, 2012 | 1995 GMC Sierra

1 Answer

Beeping noise in 1995 Chrysler LeBaron 3.0 turbo


PUT IN A NEW IGNITION SWITCH. THE KEY BUZZER IS INTERGRAL TO THE IGNITION SWITCH. IT ALARMS WHEN KEY IS LEFT IN THE CAR OR IF IT IS BROKEN IT ALARMS FOR ALL YOUR REASONS.

Oct 11, 2012 | Chrysler LeBaron Cars & Trucks

1 Answer

How do I remove the windshield wiper arm from a 1995 chrysler lebaron convertable?


To remove the wiper arm from a 91-94 LeBaron Convertible:
1: Remove the blade first. (Hood up was easier on mine)
2: From under the hood, lift arm high enough so you can get the small tab at the base of the arm to slide back toward the windshield about 1/4 inch. The tab won't move back until the arm is lifted enough to make clearance for the tab. With the tab moved back, it will keep the arm from coming back down if done correctly but BE CAREFUL that the blade doesn't spring down onto the windshield or put a towel down in the area to cushion any accidents!
3: With the tab now pushed back and holding the arm from returning down you can now slide (jiggle) the arm off from the shaft. It may seem still locked on but if the tab is out far enough to catch the arm from returing it is far enough and you just need to wiggle just right or maybe spray some WD-40 to help, but you really shouldn't need WD-40
Installation is reverse of these instructions.

Jun 13, 2012 | 1995 Chrysler LeBaron

1 Answer

Convertible top is up. D-ring turns but I cannot push up to open the top. Windows go down OK but I can't even get the top to release from the bulkhead.


The latch mechanism is broken. The D-ring is attached to a round shaft with two plates that hold sockest. The socket fits a ball end of a rod.
When you twist the d-ring it pulls/pushes rods and opens/closes latch on each corner above windshield.
You will need to pull all inside trim around inside of windshield and interior light to access the mechanism. Or try to squeeze hand between fabric and header to get rod balls back into sockets to release top so you can replace mechanism.
http://i.ebayimg.com/t/Chrysler-Crossfire-Convertible-Top-Header-Latch-Mechanism-/00/s/OTAwWDE2MDA=/$(KGrHqFHJE4FB4BQJn)(BQqL3nOJ)w~~60_57.JPG

May 27, 2012 | 2005 Chrysler Crossfire Roadster

1 Answer

Can I put a 98 Plymouth voyager transmission into a 2000 Plymouth voyager


The books say no. If all the electrical connections are the same, go for it but look at them closely. Also you will want to use the flexplate (flywheel) from the donor vehicle. It was right around 98 or 99 that Chrysler changed the bolt pattern on the torque converter. Chrysler motors are balanced by the torque converter, and this means the four converter bolt holes are not evenly spaced, and must be in the correct alignment to get all four bolts installed. one of the holes in the flywheel has flat sides. If you get that bolt in, and any other bolt in, the other two will go in. if you put that one in and the next one won't go, you need to remove that bolt and rotate the converter to the next hole. do yourself a favor and turn the converter the same way each time to avoid trying positions already tried.

Aug 17, 2011 | Chrysler Voyager Cars & Trucks

3 Answers

Lowering convertible top


There should be latches you have to pull first to unlock the top from the windshield. Pull down the sun visors, the handles should be under them. Then push the power top switch.

Mar 06, 2009 | 2008 Chrysler Sebring Convertible

2 Answers

Convertible top rattles and pops.


the adjustments can be a bit tricky but there are a couple of things you can try.....lube all the seals around the soft top and between the windows ,a light smear of vaseline can get rid of some creaks and groans.also there are 2 metal pegs where the roof locates on to top of the screen if you can find some pipe that will slide over them cut it to about 5-10mm so most of the peg is still exposed, and slide it on this tensions the roof a little and can work wonders.hope this helps.

Feb 12, 2009 | 2005 Volkswagen New Beetle Convertible

1 Answer

Replacing windshield wiper motor


Take of the wiper arm (its locked with a little metal piece.) Take a way the wiper (make a mark so you now where to put it back. Take away the grill on the topp so you later can reach part of the
motor. Take of 0 on the battery. Detach the electric connection to the motor. Relase the three scruws that holds the motor to the body.
En unscruw partly the two wiper arms and you can release the motor.

Jul 28, 2008 | Chevrolet G20 Cars & Trucks

Not finding what you are looking for?
1995 Chrysler LeBaron Logo

Related Topics:

35 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts

yadayada
yadayada

Level 3 Expert

75744 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8123 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...