Question about Mazda B-Series

1 Answer

I have a mazda 121 93 model and want to adjust the headlights correctly what are the measurements on how to do it.

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

I have a mazda 121 bubble 91 model what screw gose up and down and witch one gose in and out

Posted on Jul 15, 2012

4 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 1986 Answers

SOURCE: Can't find the adjustment knob for the headlights on a 2008 Mazda

The adjustment screws/nuts should be located either on the top of the headlamp assembly, behind the headlamp assembly, or near the frame rail by the radiator support.

You will have vertical adjustment screws for each independent beam (separate highs and separate lows, but will be same screw if highs and lows are the same bulb). You may also have additional horizontal adjustment screws as well

Park your car on a level ground 30 feet from a wall and measure the height from the ground to the bulb and mark on a wall (do this for highs beams and low beams if the bulbs are separate, if highs and lows are the same bulb, only do it for the lows)

If the headlights read VOR, then aim the brightest part or cutoff part just below the mark on the wall. If it says VOL or nothing, aim them 2 inches below the mark on the wall.

Posted on Sep 30, 2009

  • 1986 Answers

SOURCE: How do you adjust the headlights on a 2002 Mazda Miata?

The adjustment screws/nuts should be located either on the top of the headlamp assembly, behind the headlamp assembly, or near the frame rail by the radiator support.

You will have vertical adjustment screws for each independent beam (separate highs and separate lows, but will be same screw if highs and lows are the same bulb). You may also have additional horizontal adjustment screws as well

Park your car on a level ground 30 feet from a wall and measure the height from the ground to the bulb and mark on a wall (do this for highs beams and low beams if the bulbs are separate, if highs and lows are the same bulb, only do it for the lows)

For Low Beams: If the headlights read VOR, then aim the brightest part or cutoff part just below the mark on the wall. If it says VOL or nothing, aim them 2 inches below the mark on the wall.

For High Beams (if separate from low beams): Aim the headlight directly at the line you marked on the wall.

Posted on Sep 30, 2009

  • 490 Answers

SOURCE: my mazda soho 121 1998 model speed can only go up 120

speed limiter most likely its a device they install to stop you being able to speed they also make rev limiters, or your engine can only go that fast which i doubt cos 130 pretty low for an engine stop at

Posted on Oct 16, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Headlight adjustment


AIMING

The procedure outlined here is intended to provide a basic adjustment only.
  1. Park the vehicle on a level surface 25 feet (7.62 meters) from a vertical wall. There must be a horizontal reference point, such as a line on the pavement or another wall, at a right angle to the aiming wall. The fuel tank should be about 1/2 full, tire pressures must be correct and there must be a person in the driver's seat.
  2. Measure the distance from the floor to the center of each headlight. Mark these heights on the wall and draw a line between them.
  3. Measure the horizontal distance from the reference point to the center of each headlight. Make reference marks on the wall so that X marks the center of each headlight.
  4. With the headlights on low beam, the high intensity zone of the light beam should be immediately below the line and about 2 inches to the right of the center of each headlight.
  5. If adjustment is required, remove the grille and use a Phillips screwdriver to turn the adjuster screws.

Sep 28, 2015 | 1987 Volkswagen Jetta

2 Answers

How do u adjust headlghts on 1991 gmc seirre


adjustment is on the top of the light and the side.

Jun 22, 2014 | 2003 GMC Sonoma Extended Cab

1 Answer

Need to adjust the low beams on my '02 Hyundai


Headlight adjustment is fairly straight forward, you will need to park the car on a level surface with a fence or wall 25 feet away and a reference point for measurements to the right or left of the car. First measure from the reference point to the center line of the car then transfer that to the wall, second, measure from the center of the car to the center of the headlights and transfer those to the wall, third, measure from the ground to the center of the headlights and transfer that to the wall. Once all of the reference points have been transferred, adjust the left (driver's side) headlight so that the most intense part of the beam is 2 inches below and 2 inches to the right of the left mark, the right (passenger side) headlight should be adjusted so that it will be 2 inches below and 1 inch to the left of the mark. If done correctly, you will have very good night vision without blinding oncoming traffic.

P.S. Please note that any heavy objects in the car will be a factor in correct headlight adjustment, have the car loaded as it will be normally used.

Aug 20, 2011 | 2002 Hyundai Accent

1 Answer

I need to change the lights on my mazda mx5 first reg july 2005 to left hand as i now live in france?


Buy a new pair of headlights from a French Motor Factor or from your nearest Mazda dealer and just swap them over. Then go to a garage to get the headlight beams correctly adjusted. Voila!

If you want specific instructions, then you'll need diagrams which are not available online for copyright reasons, but Haynes publish the correct manual which you can either buy new or get secondhand from online suppliers like ebay and Amazon.

Sep 06, 2010 | 2005 Mazda MX-5 Miata

1 Answer

Adjust the headlight beam on 2002 Subaru Outback


two screws on each headlight control the direction the headlights are aimed. One screw, usually at the top but sometimes below the headlight, adjusts the headlight up and down. The other screw, located to one side, controls the headlight from right to left. Turning the appropriate screw one direction or the other will change the direction the headlight points.
In order to aim your headlights you need to have a flat vertical surface you can aim your headlights at in front of a level surface on which to park the car. If your driveway is level your garage door is the perfect place to aim your headlights.
The tools you will need for this job are simple. Masking tape is used to mark where the headlights are to be aimed and a screwdriver is needed to adjust the headlights. A tape measure will be necessary to measure the distance of the vehicle to the surface you're using to check the aim and to measure the up and down distances from your marks

Nov 09, 2009 | 2002 Subaru Outback

1 Answer

My headlights wont adjust by the motors is there a manual adjustment on them i have a mazda 6 2.0 ts and if so where is it


The adjustment screws/nuts should be located either on the top of the headlamp assembly, behind the headlamp assembly, or near the frame rail by the radiator support.

You will have vertical adjustment screws for each independent beam (separate highs and separate lows, but will be same screw if highs and lows are the same bulb). You may also have additional horizontal adjustment screws as well

Park your car on a level ground 30 feet from a wall and measure the height from the ground to the bulb and mark on a wall (do this for highs beams and low beams if the bulbs are separate, if highs and lows are the same bulb, only do it for the lows)

For Low Beams: If the headlights read VOR, then aim the brightest part or cutoff part just below the mark on the wall. If it says VOL or nothing, aim them 2 inches below the mark on the wall.

For High Beams (if separate from low beams): Aim the headlight directly at the line you marked on the wall.

Sep 06, 2009 | 2004 Mazda 6

2 Answers

Can't find the adjustment knob for the headlights on a 2008 Mazda


The adjustment screws/nuts should be located either on the top of the headlamp assembly, behind the headlamp assembly, or near the frame rail by the radiator support.

You will have vertical adjustment screws for each independent beam (separate highs and separate lows, but will be same screw if highs and lows are the same bulb). You may also have additional horizontal adjustment screws as well

Park your car on a level ground 30 feet from a wall and measure the height from the ground to the bulb and mark on a wall (do this for highs beams and low beams if the bulbs are separate, if highs and lows are the same bulb, only do it for the lows)

If the headlights read VOR, then aim the brightest part or cutoff part just below the mark on the wall. If it says VOL or nothing, aim them 2 inches below the mark on the wall.

Jun 09, 2009 | 2008 Mazda Mx 5 Miata

1 Answer

Headlight aiming too high - how to adjust?


pop your hood open and on flat surface check too see where the beads are in the bubble levels,if they are off then there are 2 adjustments on each headlight,some require special tool they look like little gears on the adjusters. make sure car is on good flat surface

May 11, 2009 | 1995 Mazda 626

1 Answer

2005 RX8 headlights


on each headlamp assembly, there will be either one or two plastic nuts that you can turn.

If you only have one nut on each, that will adjust the vertical aim of the headlights.

If you have two nuts on each, one will adjust the vertical and the other will adjust the horizontal.

Park your car on a level ground 30 feet from a wall and measure the height from the ground to the bulb and mark on a wall (do this for highs beams and low beams if the bulbs are separate, if highs and lows are the same bulb, only do it for the lows)

If the headlights read VOR, then aim the brightest part or cutoff part just below the mark on the wall. If it says VOL or nothing, aim them 2 inches below the mark on the wall.

Apr 09, 2009 | 2005 Mazda RX-8

1 Answer

How do you adjust the headlights on a 2002 Mazda Miata?


The adjustment screws/nuts should be located either on the top of the headlamp assembly, behind the headlamp assembly, or near the frame rail by the radiator support.

You will have vertical adjustment screws for each independent beam (separate highs and separate lows, but will be same screw if highs and lows are the same bulb). You may also have additional horizontal adjustment screws as well

Park your car on a level ground 30 feet from a wall and measure the height from the ground to the bulb and mark on a wall (do this for highs beams and low beams if the bulbs are separate, if highs and lows are the same bulb, only do it for the lows)

For Low Beams: If the headlights read VOR, then aim the brightest part or cutoff part just below the mark on the wall. If it says VOL or nothing, aim them 2 inches below the mark on the wall.

For High Beams (if separate from low beams): Aim the headlight directly at the line you marked on the wall.

Jan 04, 2009 | 2002 Mazda Miata

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

334 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mazda Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8201 Answers

Are you a Mazda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...