Question about Chevrolet Cavalier

2 Answers

How do i take off the window roller to get my door panel off

Posted by on

2 Answers

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Chevrolet Master
  • 3,640 Answers

There is a c-clip on back of handle on a lot of vehicles. this is how I do it without a tool for this. take a clean rag put behind handle and work it back and forth. when it catches the clip it usually pops it off. or you can go to any auto parts store and buy a tool to remove handle clip.

Posted on Mar 20, 2011

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 388 Answers

There is a small horse shoe shaped clip around the inside of the crank handle. There is a special tool for removing the clip but if you can push the door panel in far enough you may be able to pop it off with two small screw drivers. For the trouble it takes I'd buy the special tool from an auto parts store since it's cheap.

Posted on Mar 20, 2011

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My rear window shade is not working


You will need to remove the door panel in order to
prevent further damage to the electric window motor in
your door. Electric window motors are typically very
expensive so you should be careful not to damage it. You
should be able to easily remove the roller blinds once
the door panel is removed.

____________________

BMW scanner 1.4.0

Jun 25, 2012 | BMW Cars & Trucks

2 Answers

Electric windows


The motor is not grounded through the frame... Direction of rotation is controlled by apply B+ to one lead and ground to the other.

Jun 26, 2008 | 2002 Chevrolet Camaro

2 Answers

Rear passenger side window just fell down and won't go back up. is this possible?


Yes its possible, the roller has come out of the track You would have to remove the arm rest and panel screws off and remove the cover with the door open unsnap the clips on the door and let the door hang down use a flashlight to see the roller that's off track pick the glass up and slid into the glass guides and move the window up till you get the roller into the track, have the key on in case you need to raise the window up or down to get it to go into the track, if the roller is broke you can buy one at a junk yard, if the roller is ok then the stop pin may have fallen out and you will have to use a roll pin to keep the roller from coming out of the track. Hope this helps.

May 14, 2010 | 2004 Cadillac CTS

1 Answer

How to fix drivers window.the window just feel in to the door panel. it is a power window. WHAT WOULD BE THE PROBLEM.


window came of track inside door maybe rollers came out of place have to remove door panel to access

Apr 05, 2010 | 1991 Chrysler New Yorker

1 Answer

How to install a door glass for a Chev C10 . I am have problems install the glass at the Drivers door. I need some help. As soon as possible


GM Full-Size Trucks 1980-1987 Repair Guide

REMOVAL & INSTALLATION
(see Figures 1 and 2)

Non-Stationary Door Glass
  1. Lower the door glass completely.
  2. Remove the trim panel from the door.
  3. Remove the ventilator assembly as previously outlined.
  4. Slide the glass forward until the front roller is in line with the notch in the sash channel.
  5. Push window forward and tilt the front portion of window up until rear roller is disengaged.
  6. Put window assembly in normal position (level) and raise straight up and out.
  7. Installation is the reverse of removal.
4faff09.jpg

Fig. 1: Door window and regulator

0c5eed4.jpg


Fig. 2: Removing the door glass

Manual Door Window Regulator
(see Figure 3)
  1. Raise the glass to the full up position and tape it to the door frame with fabric tape.
  2. Remove the door trim panel.
  3. Remove the regulator to door panel attaching bolts.
  4. Slide the regulator assembly rearward, disengaging the rollers from the sash panel.
A notch is provided in the sash panel to allow disengagement of the forward roller on the window regulator.
  1. Collapse and remove the regulator assembly through the access hole in the door.
To install:
  1. Prior to installation, lubricate the motor drive gear and regulator sector teeth.
  2. Collapse the regulator and insert it through the access hole in the door.
  3. Unfold the regulator and engage the forward roller to the sash cannel at sash channel notch.
  4. Slide the regulator rearward to engage the rear roller to the sash channel. Also engage the lower roller to the regulator rail.
  5. Slide the regulator into its proper position, and insert the regulator drive through the door panel.
  6. Attach the regulator to the door.
  7. Install the door trim panel.
af77872.jpg

Fig. 3: Manual window regulator

Power Window Regulator and Motor
(see Figure 4)


aa9dd10.jpg
Fig. 4: Power window regulator and motor
  1. Raise the glass to the full up position and tape it to the door frame with fabric tape.
  2. Disconnect the negative battery cable.
  3. Remove the door trim panel.
  4. Remove the remote control bolts and lay the control aside for access.
  5. Remove the regulator to door panel attaching bolts.
  6. Disconnect the harness from the regulator.
  7. Slide the regulator assembly rearward, disengaging the rollers from the sash panel.
A notch is provided in the sash panel to allow disengagement of the forward roller on the window regulator.
  1. Remove the regulator assembly through the access hole in the door.
CAUTION Step 9 must be performed when the regulator is removed from the door. The regulator lift arms are under tension from the counterbalance spring and can cause serious injury if the motor is removed without locking the sector gear in position.
  1. Drill a hole through the regulator sector gear and back plate. DO NOT drill a hole closer than 1 /2 inch; to the edge of the sector gear or back plate. Install a pan head sheet metal tapping screw (No. 10-12× 3 /4 inch;) in the drilled hole to lock the sector gear in position.
  2. Remove the motor to regulator attaching screws and remove the motor from the regulator.
To install:
  1. Prior to installation, lubricate the motor drive gear and regulator sector teeth.
  2. Install the motor to the regulator. Make sure the motor and sector gear teeth mesh properly before installing the retaining screws.
  3. Remove the screw locking the sector gear in the fixed position.
  4. Reposition the motor in the door and install the wiring connector.
  5. Attach the regulator to the door.

I really hope help you with this (remember rated this help) Good luck.

Oct 06, 2009 | 1980 Chevrolet Corvette

1 Answer

Driver side window does not crank up straight


It sounds like the window may have slipped off it's guide rail or support rail. The window base connects to the motor via some bars that resemble a scissor lift.

On the inside trim, you can remove screws that are by the door handle, arm rest, under door and side of door and then gently pull back on the panel as there will also be retaining clips attached and you don't want to break them. You'll need to lift the door panel upwards in order to get it off the window ledge. Pull back the weather seal and you'll be able to get to everything

Sep 18, 2009 | 1997 Dodge Dakota

1 Answer

Remove inside door panel


plastic place pins all along door carefully pop out with screw driver as to not damage them there should be screws in places too ie inside rest and or window roller

Sep 16, 2009 | 1991 Oldsmobile 88

1 Answer

1993 Jeep Grand Cherokee Lorado - window tipped, roller broken


If the motor still actuates and moves when activated then no replacement is required. When the roller cracked it may have however burnt out the motor. replacing the roller and realigning the window is very easy.. the parts.... go see your local auto wrecker. they may be able to sell you a roller or 2 from a wrecked cherokee(and maybe pick up a spare motor while you're at it. This is usually the cheapest solution for parts.

Jul 04, 2009 | Jeep Grand Cherokee Cars & Trucks

2 Answers

Side door Plastic rollers are worn out causing door to be hard to open or close. door has begun to fall off track.


I took the cheep way out. I got a used shower door roller mechanism. (the kind that slides in tracks.) I dremmeled out the plastic rollers and then shaved them down to the right size. then took off the door and poped them right onto where the old rollers were. Perfect fix with a bit of ingenuity. 50 cents and about one hour of work.

May 14, 2009 | 1991 Toyota Previa

2 Answers

Need to change door speaker, cant get the door paneling off nor the manual window roller upper off.


Take a flat screwdriver or other similar flat tool,gently pry between the window handle and door panel,you should just be able to see the clip that holds it on to the metal shaft of the window gear,you'll need a pair of needle nose pliers or a flat screwdriver to pull it off,to put it back on you put it on the widow handle and just pop it on the metal shaft.Hope this helps.

May 09, 2009 | 1998 Pontiac Sunfire

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

90 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

75744 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8123 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...