Question about 1999 Chevrolet Tahoe

1 Answer

What are the rocker arm settings ffor the 5.7 Vortex engine?

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Governor:

    An expert whose answer got voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 130 Answers

Tighten rockers till you cant spin pushrods then back off just until they start to spin

Posted on May 09, 2011

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

After changing the bottom end of a Chevy 350 vortex how long before the oil pressures up to reach the rocker arms?


Did you prime the oil pump? Pack it with vasoline? Crank the engine without starting it until oil pressure came up?

May 19, 2015 | Cars & Trucks

1 Answer

How to set rocker arms on 2.2 4clyder s10 pickup


Rocker arms on a 2.2l gm engine are non-adjustable, they should have a shoulder stud not threaded all the way down just torq them.

Nov 04, 2014 | Cars & Trucks

2 Answers

How to install rocker arms on a Pontiac grand am 2001 V-6


Hi there:

Rocker Arms & Pushrods


Removal & Installation

3.1L & 3.4L Engines
Left Side

  1. Before servicing the vehicle, refer to the precautions section.
  2. Drain the cooling system to a level below the coolant pipe on the front of the engine.
  3. Remove or disconnect the following:
    NOTEKeep the pushrods in order. Intake pushrods are 5 3 / 4 inches long and exhaust pushrods are 6 inches long.


    Negative battery cableSpark plug wiresHeater bypass pipePositive Crankcase Ventilation (PCV) valve and hoseRocker arm cover


    Rocker arms and pushrods

To install:

  1. Lubricate all the valvetrain components with engine oil.
  2. Install or connect the following:

    Pushrods and the rocker arms. Torque the bolts to 24 ft. lbs. (32 Nm).Rocker arm cover using a new gasket. Torque the rocker cover bolts to 89 inch lbs. (10 Nm).PCV valve and hoseHeater bypass pipe. Torque the screw at the water pump to 106 inch lbs. (12 Nm), the bolt at the cylinder head corner to 18 ft. lbs. (25 Nm) and the nut to 18 ft. lbs. (25 Nm).Spark plug wiresNegative battery cable
  3. Refill the cooling system.
  4. Start the vehicle and verify no leaks.




3_4_2013_5_26_48_pm.gif


Right Side
  1. Before servicing the vehicle, refer to the precautions section.
  2. Remove or disconnect the following:
    NOTEKeep the pushrods in order. Intake pushrods are 5 3 / 4 inches long and exhaust pushrods are 6 inches long.


    Negative battery cableAlternator bracket on 2005 modelsSpark plug wires from the spark plugs and the upper intake plenum wire retainerPower brake booster vacuum pipe from the intake plenumAccessory drive beltAlternator, if necessaryIgnition coil assembly and Evaporative Emissions (EVAP) canister purge solenoid as an assemblyRocker arm cover


    Rocker arms and pushrods

To install:

  1. Lubricate all the valvetrain components with engine oil.
  2. Install or connect the following:

    Pushrods and the rocker arms. Torque the bolts to 24 ft. lbs. (32 Nm) plus an additional 30 degree turn.Rocker arm cover using a new gasket. Torque the rocker cover bolts to 89 inch lbs. (10 Nm).Ignition coil and EVAP solenoid assemblyAlternator, if removed. Torque the bolts to 37 ft. lbs. (50 Nm).Accessory drive beltPower brake booster vacuum pipe to the plenumSpark plug wiresNegative battery cable
  3. Start the vehicle and verify no leaks.





Hope this helps.

Mar 04, 2013 | Cars & Trucks

1 Answer

P 2647"A" Rocker Arm Actuator


Your going to need a air pressure regulator or better yet if the ECM found fault price it and replace it
  1. Start the engine, and let it run for 5 minutes, then turn the ignition switch to LOCK (0).
  2. Remove the cylinder head cover.
  3. Set the No. 1 piston at top dead center (TDC).
  4. Move the intake secondary rocker arm A for the No. 1 cylinder. The secondary rocker arm A should move independently of the secondary rocker arm B.
    1. If the intake secondary rocker arm A moves freely, go to step 5.
    2. If the intake secondary rocker arm A does not move, remove the secondary rocker arms as an assembly, then check that the pistons in the secondary rocker arms move smoothly. If any rocker arm needs replacing, replace the secondary rocker arms as an assembly, then retest.
    3. Repeat step 4 on the remaining intake secondary rocker arms with each piston at TDC. When all the secondary rocker arms pass the test, go to step 6.
    4. Check that the air pressure on the shop air compressor gauge indicates over 400 kPa (4.0 kgf/cm2, 57 psi).
    5. Inspect the valve clearance.
    6. Install a 10 x 1.0 mm adapter to the inspection hole, then connect the air pressure regulator
  5. With the specified air pressure applied, move the intake secondary rocker arm A for the No. 1 cylinder. The secondary rocker arm A and secondary rocker arm B should move together. If the intake secondary rocker arm A does not move, remove the secondary rocker arms as an assembly, and check that the pistons in the secondary rocker arms move smoothly. If any rocker arm needs replacing, replace the secondary rocker arms as an assembly, then retest.
  6. cansmo_32.gif
cansmo_33.gif

Aug 23, 2011 | Honda Accord Cars & Trucks

1 Answer

What is the torq setting for the rocker arms on a 91 crown vic with a 5.0L


zjlimited_1679.jpg

Fig. 2: Rocker arm assembly - 5.0L and 5.8L engines

* Apply engine oil or assembly lubricant to the valve stem tip and pushrod end. Also apply lubricant to the rocker arm and fulcrum seat contact surfaces.
* Rotate the crankshaft until the lifter is on the camshaft base circle (all the way down) and install the rocker, fulcrum seat and fulcrum bolt. Tighten the bolts to 18-25 ft. lbs. (24-34 Nm).
*
Install the rocker arm cover(s).

Hope this helps.

Aug 03, 2011 | 1991 Ford LTD Crown Victoria

1 Answer

2001 grand cherokee 4.0l valve rocker torque specs


5 million made.
it's in the fsm book
posted here over 300 times.
are you asking , how to set rockers ?

chapter 9 page 27
------------------text fsm---------------------
INSPECTION
Inspect the pivot surface area of each rocker arm.
Replace any that are scuffed, pitted, cracked or
excessively worn.
Inspect the valve stem tip contact surface of each
rocker arm and replace any rocker arm that is deeply
pitted.
Inspect each push rod end for excessive wear and
replace as required. If any push rod is excessively
worn because of lack of oil, replace it and inspect the
corresponding hydraulic tappet for excessive wear.
Inspect the push rods for straightness by rolling
them on a flat surface or by shining a light between
the push rod and the flat surface.
A wear pattern along the length of the push rod is
not normal. Inspect the engine cylinder head for
obstruction if this condition exists.
INSTALLATION
NOTE: This procedure can be done with the engine
in or out of the vehicle.
(1) Lubricate the ball ends of the push rods with
Mopart Engine Oil Supplement, or equivalent and
install push rods in their original locations. Ensure
that the bottom end of each push rod is centered in
the tappet plunger cap seat.
(2) Using Mopart Engine Oil Supplement, or
equivalent, lubricate the area of the rocker arm that
the pivot contacts. Install rocker arms, pivots and
bridge above each cylinder in their originally position
(Fig. 23).
(3) Loosely install the capscrews through each
bridge.
(4) At each bridge, tighten the capscrews alternately,
one turn at a time, to avoid damaging the
bridge. Tighten the capscrews to 28 N·m (21 ft. lbs.)
torque.
(5) Install the engine cylinder head cover (Refer to
9 - ENGINE/CYLINDER HEAD/CYLINDER HEAD
COVER(S) - INSTALLATION).

Mar 13, 2011 | Jeep Grand Cherokee Cars & Trucks

1 Answer

How do i set the rocker on a 1999 5.7l vortex stadicly


Static rocker adjustment is done by tightening the rocker down (with the cam lobe for that valve "out of tension"...turn the engine by hand to adjust any that have lobe pushing up on the lifter. Tighten the rocker while turning the pushrod with your fingers. When you cannot turn it easily, turn back a quarter turn or less, till you can turn it again. You will still need to do a "running" adjustment but static adjustment will get you in the "ballpark" for starting engine..

Sep 16, 2009 | 1999 GMC Yukon

1 Answer

Changing Camshaft seal


1. Install the camshaft after lubricating the journal of the camshaft with engine oil. 2. Install the camshaft bearing caps.a0b9a5d.jpg
3. Install the ignition coil. 4. Install the rocker arm and rocker arm shaft. Refer to "Rocker Arms and Rocker Arm Shafts" section. 83e48db.jpg 5. Using special tools, Camshaft Oil Seal Installer (09221-21000), press fit the camshaft oil seal. Be sure to apply engine oil to the external surface of the oil seal. Insert the oil seal along the camshaft front end and install by driving the installer with a hammer until the oil seal is pulley seated. bda0592.jpg 6. Install the camshaft sprocket and tighten the bolts to the specified torque. 2cbbe98.jpg

May 05, 2009 | 1996 Hyundai Accent

1 Answer

How to adjust rocker shaft on discovery td5


There are adjustment screws on the rockets according to RAVE.
The procedure is as follows:
1) Rotate the engine clockwise until No 1 injector lobe is at full lift.
2) Rotate rocker adjusting screw clockwise until the injector plunger is felt to bottom out.
3) Rotate rocket adjusting screw anti-clockwise one complete turn to give plunger the required bump clearance and tighten rocker arm adjusting screw locknut to 16Nm. Ensure the screw does not turn as the locknut is tightened.
4) Carry out the procedure for the remaining 4 rocker arms.
5) After completion of rocker arm adjustment slowly rotate engine clockwise 2 complete turns by hand to ensure that no injectors are bottoming out on their plungers.

Apr 08, 2009 | 2003 Land Rover Discovery

Not finding what you are looking for?
1999 Chevrolet Tahoe Logo

Related Topics:

51 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

75066 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7754 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...