Question about 2007 Suzuki Forenza Sedan
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Posted on Jan 02, 2017
SOURCE: location of cam position senor
Not a bad job to replace the cam position sensor, it took about two hours cost about $150.00 with oem parts. First remove air filter box,remove plastic spark plug cover. Jack up engine about an inch remove engine mount. Now you can access sensor through a convenient cover that mounts around engine mount bracket extending from engine block.( one ten millimeter bolt) Remove accessory drive belt for a little extra room and replace with new one while you are in there. Just between the two cam gears you will see a torx screw that aligns the switch when in installed. DO NOT REMOVE THIS Just above the torx screw is a reverse torx screw (6 millimeter) Put a shop rag in the access hole to catch the screw just in case you drop it ,( so it does not fall into timing belt cover) Put something "sticky" in the 6 millimeter socket such as gasket sealer to keep from losing screw. remove. Pull switch up from inside spark plug cover and install new one through the same. reinstall 6 millimeter bolt. Switch is self aligning. Reinstall belt, engine mount, air box. Doing this myself probably saved me about $150.00 to $200.00 dollars
Posted on Jun 08, 2008
Most likely cause of this is a clogged thermostat. Especiallly if you've ever used a sealer in the past, the thermostat clogs with age and a bad thermostat will tend to back up and fill your reservoir tank. Best of luck with this situation and I hope you've found this post a solution to your problem. All the best!
Posted on May 13, 2009
there is no dip stic on the forenza no need to go to the dealer and pay for it simply jack the entire car off the ground enough to get yourself under it make sure u support it with appropriate stands. you can check the fluid by removing the plug from the side of the trans u will need a special tool for this u can get from an auto parts store after removing the plug check to make sure the fluid is right to the brim of the plug hole then turn the car on and shift through the gears R,D,1,2,4 and then back again hold in each gear for about 5 sec then turn the car off crawl back under and check again . if low add a little at a time until its filled u can get a small hand pump with a tube on it from auto store u put this in a quart of trans fluid makes the job alot easier . as for the other problem it is you Trans range sensor $65 dollars from the dealer or $45 from OEMsuzukiparts.com not very hard to change Hope this helps
Posted on Oct 11, 2009
Right on the transmission, to the right side of the engine bay as you are looking down on it. It is a black plastic part that is bolted on the transmission with two 10mm bolts, and connected to the transmission with rod and clip. It is partially obstructed by the radiator hose, but otherwise really easy to get to.
Posted on Jan 28, 2010
Tips for a great answer:
Dec 22, 2016 | Suzuki Cars & Trucks
Jun 14, 2014 | 2006 Suzuki Forenza
Apr 25, 2012 | 2007 Suzuki Forenza Sedan
Jan 25, 2011 | 2006 Suzuki Forenza
Jan 07, 2011 | 2004 Suzuki Forenza
Oct 16, 2010 | 2004 Suzuki Forenza
Aug 04, 2009 | 2004 Suzuki Forenza
May 13, 2009 | 2004 Suzuki Forenza
64 people viewed this question
Usually answered in minutes!