Question about Ford E-150

1 Answer

Cant get the bottom screw out - E-150 Ford Cars & Trucks

Posted by on


1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 20 achievements.


    An expert that got 10 achievements.


    An expert that got 5 achievements.

  • Master
  • 2,418 Answers

Dear Jessie we need way more info to help with your problem. Please repost with as much info as you can give. Thanks.

Posted on Mar 19, 2011


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Cant get to bott0m radiator hose on vectra 2000 2.6 v6 to drain

I believe the only option is to remove the lower radiator hose. I'm not very familiar with that model, but there should be a way to get to it. You may have to go in from the bottom. If there's a plastic shield in the way (some cars have a plastic 'tray' under the motor), they can usually be removed with 4-6 screws or bolts.

May 04, 2016 | Cars & Trucks

1 Answer

97 mercury cougar xr7 how do i get door panel off if I cant open door?

It should still be possible, using a little bit of force. all screws and bolts holding on the panel are accessible, even with the door closed...but the panel maybe slightly pinched on the front and rear ends, and possibly on the bottom...but pulling hard on the handle once every bolt and screw is removed should force the panel loose

Apr 18, 2014 | 1997 Mercury Cougar XR7

1 Answer

Cant get the alternator fuse out

The alternator fuse is screwed on from the bottom up inside the fuse box. To remove the alternator fuse, you have to unscrew the whole fuse box from the car and on the bottom of the box are more screws to open the box. Once its open you will see one or two little screws holding the alternator fuse in place, easy. Unless you buy the manual for the car, you'll have to break one to pieces trying to get it out, to figure out how to do it, like i did.

Mar 27, 2014 | 1989 Toyota Cressida

1 Answer

I have a suzuki samuri I am rebuilding and cant get the gear shift knob off is it a. screw on or is.pressed on

Probably screwed on, but check for like a set screw near the bottom of knob that might be holding it.

Jan 24, 2013 | Cars & Trucks

1 Answer

I cant find my windsheild wiper fluid tank. It is busted near the bottom and wont hold cleaner

To gain access to washer motor, remove screws securing left front inner fender panel (may require removing wheel for access).

Disconnect washer motor electrical connector and hose. Remove screws and reservoir.

To install, reverse removal procedure.

Jan 20, 2010 | 1995 Chevrolet Corsica

1 Answer

Cant get the door panel off

There are three T-25 head screws along the bottom of the inside door panel. Remove them. The face of the inside door handle is removable--just pry it off, probably don't even need a screwdriver to get it off. Underneath, you'll find two #1 phillips head screws. Remove them. Finally, grasp the door panel from the bottom and pull up. It hangs over a little lip against the window. Watch the door lock, make sure the panel clears that. You should have access to all the wiring harnesses that keep the panel attached.

Sep 29, 2009 | 2000 Volkswagen Beetle

1 Answer

I cant figure out how to change the driver's side headlight

You have two screws at the top of the trim cover. remove them and tilt top towards you and remove from slots at bottom.
There are four screws holding the ring around the lamp. spray them with solvent and remove them the rest is just unplug and plug back in don't put it back upside down. (use a really good new screwdriver and if screws on ring won't come out after soaking tap the back of the screwdriver with a hammer to break rust in threads)

May 24, 2009 | 1998 Jeep Grand Cherokee

1 Answer

Glow plugs

have you gotten any part of it to come out? it sounds like it may be carboned up on the bottom side and u may have stripped the threads out. which glow plug is it

Nov 02, 2008 | 2004 Dodge Sprinter

1 Answer

85 corvet i cant get the panal off my battery

You need a torx wrench. Screws are on the bottom and back of front fender.

Nov 01, 2008 | 1985 Chevrolet Corvette

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

21 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts


Level 3 Expert

80608 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers


Level 3 Expert

5687 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides