Question about 1993 Mercury Grand Marquis

1 Answer

How do you remove the dash board on a grand marquis 1996

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

It is best to remove the front seat then remove the outer trim work on the dash which are fastened with clips. Then remove the screws which hold the heater/AC controls and also the dash panel such as speedometer etc. Remove the lower plastic shield from around the steering column and disconnect the transmission gear position indicator cable. Remove the plastic covering between the steering column and the drivers knees. Their are mounting bolts in the dash and under neath as well and also barbed fasteners. Remove the steering wheel column mounting bolts and it's support brackets. Lower the steering column to the floor. Remove the front door coverings located near the door hinges. Be carefull not to break the fasteners. They pry out of the door weather stripping and then you lift up on them. This will give you access to the lower dash mounting brackets.
With the steering column lowered remove the plastic trim under the windshield. It pops out and givces you access to the front dash mounting screws. disconnest the headlight photo cell control, disconnect the clock, radio and all other pigtail connections that would otherwise interfear with removing the dash. I remove the speedometer electronic cluster as well. Disconnect the AC/heater upper and lower duct work. They are generally fastened with screws and and you have to look for them.
The dash is fastened by the previously mentiond screws located below the windshield and by bolts located near the door which can be seen when the trim is removed also by lower bracket that are braced and is easily identified. These bolts heads are # 10 metric. I have probably forgotten a couple of items but this should get you through the worse of it.
The Mercury Grand Marquis and the Crown Victoria both tend to have blend door problems for the climate control and the dash has to come out to access the blend door control.

Posted on Aug 19, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where are the screws located to remove the heater


under the dash , on the passenger side , behind the glove box . on some fords , you have to take the blower motor out to get to some of the screws to the heater box .sometimes the heater box has threaded studs that go through the firewall with fastening nuts under the hood at the bottom of the a c box .

Oct 05, 2014 | 1996 Mercury Grand Marquis

1 Answer

Is there a fuse for the entry pad on a 1996 Mercury Grand Marquis?


Fuse #8 on the interior fuse panel and 20amp on the engine compartment fuse box, but if either of these were blown you would have several other things not working, door locks from any switch, dash board wouldn't light up, cluster radio heater control and d o on.if all this is working, I would start my testing at the door pad.they get little cracks in them over time and water gets inside and corrodes the switch, pad, internally. .ive done a lot up hete on east coast. .

Apr 30, 2014 | 1996 Mercury Grand Marquis

1 Answer

Dashboard removabe 93 grand marquis


Long and laborious...About 40 screws and bolts.

Screws and bolts are found on the side of the dash, and under the dash. Keep removing them until you find the next binding point, and remove another fastener. Eventually you will remove them all...

Jan 26, 2014 | 1993 Mercury Grand Marquis

1 Answer

Location of heater control valve on a 1996 Grand Marquis


It is right there in the in the dash. It is the whole panel, where you have all your fan speed, heater , ac and vents.

Apr 16, 2011 | 1996 Mercury Grand Marquis

1 Answer

Dash removal on 1006 mercury grand marquis


Hello, to remove the dash follow this steps:

1. Pry all the woods pieces off of by pulling them away from the dash.

2. Use two ford radio removal tools to remove the radio in the marquis. Place one tools inside two of the four holes in the front of the radio, and the other tools in the other two holes,Pull them away from each other and out of the dash board. Disconnect the wiring harness from the back of the stereo.

3. Remove the screw surrounding the radio using a Phillip head screwdriver. Do not forget to remove the two on the other side of the radio.

4. Remove all the screw around the instrument cluster using a Phillip head screwdriver.

5. Use the steering wheel tilt level to tilt the steering wheel all the way down .

6. Gently pry out the dash , making sure to disconnect the two wiring harness behind the dash board panel before pulling it out completely.

Thanks

Aug 24, 2010 | 2003 Mercury Grand Marquis

1 Answer

Where is the fuel pump located on the 1996 Grand Marquis?


1996 Mercury Grand Marquis 4.6L SFI 8cyl
199b5bb.jpg

Fig. 1: The fuel pump is located in the fuel tank. On some models it can be viewed from the side as shown here

c2d848f.jpg

Fig. 2: Electric fuel pump removal

The Relay - Fuel Pump is located: Under hood, driver side, front side of wheelwell, mounted in relay block.


Hope this help to solve it (remember comment and rated this).

Aug 02, 2010 | 1996 Mercury Grand Marquis

Not finding what you are looking for?
1993 Mercury Grand Marquis Logo

1,077 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mercury Experts

yadayada
yadayada

Level 3 Expert

61037 Answers

Fordexpert

Level 3 Expert

5331 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Are you a Mercury Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...