Question about Ford Ranger

1 Answer

What is the valve clearance for a ford ranger 2.5 wl engine?

Posted by on


1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 20 achievements.


    An expert that got 10 achievements.


    An expert that got 5 achievements.

  • Ford Master
  • 990 Answers

You must look at the manual for that motor and truck exhaust and intake are different

Posted on Sep 01, 2017


6 Suggested Answers

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

  • 96 Answers

SOURCE: i need to know the vavle clearance of nissan z20 engine.

Application In. (mm)
Intake .010-.013 (.26-.34)
Exhaust .011-.015 (.29-.37)

Posted on Mar 20, 2009

  • 94 Answers

SOURCE: where is the pcv valve located on a 2003 ford ranger

  • The PCV valve can be located in several places. The most common location is in a rubber grommet in the valve cover. It can be installed in the middle of the hose connections, as well as installed directly in the intake manifold.
  • Once the PCV valve is located, make sure all the PCV system hoses are properly connected and that they have no breaks or cracks.
  • Remove the air cleaner and inspect the air and crankcase filters. Crankcase blowby can clog these with oil. Clean or replace such filters.
  • Oil in the air cleaner assembly indicates that the PCV valve or hoses are plugged.
  • Make sure you check these and replace the valve and clean the hoses and air cleaner assembly.
  • When the PCV valve and hose are in satisfactory condition and there is oil in the air cleaner assembly, perform a cylinder compression test to check for worn cylinders and piston rings.
  • Posted on Feb 27, 2009

    • 251 Answers


    Under hood, center, rear engine area, mounted on upper rear of engine block clearpixel.gif

    Posted on Dec 06, 2008

    • 54 Answers

    SOURCE: Need Valve clearance for '93 kh ford laser

    0.10 - 0.15mm inlet
    0.18 - 0.23mm exhaust
    but you must be carefull because the top of the valve seat becomes concave from wear, a feeler guage will not give the most accurate reading, hope i have been of some hel

    Posted on May 14, 2009

    • 546 Answers

    SOURCE: I need to know the valve clearance for a 1985 ford

    Ford uses hydraulic valve lifters,turn engine over to install rockers,engine oil pressure keeps valves constantly adjusted.

    Posted on Oct 12, 2009

    Add Your Answer

    Uploading: 0%


    Complete. Click "Add" to insert your video. Add



    Related Questions:

    1 Answer

    Tappet clearance ford ranger 2.5 wl engine

    get the service and repair manual get the solution and you can get the manual from the given link

    May 09, 2018 | Ford Cars & Trucks

    1 Answer

    Need valve clearance settings for ford ranger wl 2.5 engine with turbo

    At very cheap rates you can go for manuals from this store. Just c ford ranger

    Sep 29, 2017 | Ford Cars & Trucks

    1 Answer

    Wha is the valve clearance for ford ranger 2.5l wl engine?

    Idk, but I know it is a high clearance engine. So, if the timing belt breaks, the valves won't hit your pistons, and no internal damage will occur.

    Oct 01, 2015 | Ford Cars & Trucks

    1 Answer

    I need to know the fireing order on a 2.8l engine in a 1985 ford ranger

    Tune Up

    Spark Plug


    Spark Plug Gap


    Ignition Timing

    10 degrees BTDC

    Firing Order


    Distributor Rotation


    Valve Clearance Intake


    Valve Clearance Exhaust


    Aug 04, 2011 | 1984 Ford Ranger

    1 Answer

    Wat is valve clearance on ford ranger 2002

    If you have a 2.3L engine the tappet to valve clearances are:

    Intake = 0.22 - 0.28 mm (0.008 - 0.011 in)
    Exhaust = 0.27 - 0.33 mm (0.010 - 0.013 in)

    If you have either the 3.0L or 4.0L, there are no adjustments because they use hydraulic lifters.

    Nov 12, 2010 | 2002 Ford Ranger Regular Cab

    1 Answer

    I need to know the valve clearance for a 1985 ford ranger 2.8 liter engine?

    Ford uses hydraulic valve lifters,turn engine over to install rockers,engine oil pressure keeps valves constantly adjusted.

    Oct 12, 2009 | 1985 Ford Ranger

    Not finding what you are looking for?
    Cars & Trucks Logo

    Related Topics:

    2,552 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Ford Experts


    Level 3 Expert

    80263 Answers

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    22326 Answers


    Level 3 Expert

    5687 Answers

    Are you a Ford Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides