Question about 1996 Chevrolet Tahoe

1 Answer

Trying to locate the camshaft position on my 1996 chevy tahoe 4wd

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 83 Answers

I believe they had a distributor in some and some were DIS system. If yours has a distributor, the CMP is in there and the distributor has to be replaced as a whole unit.

If you have a DIS system, Here is a pic that might help.


trying to locate the camshaft position on my 1996 - ldtrisch_36.jpg

Posted on Mar 19, 2011

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where is the camshaft position sensor on a 1996 toyota tacoma 2.7 located.


Camshaft Position Sensor

1996 Toyota Truck Tacoma 2WD 2.4L EFI DOHC 4cyl

The Camshaft Position Sensor is located: Under hood, passenger side, front engine area, below valve cover, mounted in distributor

Oct 14, 2014 | 1996 Toyota Tacoma

1 Answer

Where is the crankshaft and camshaft position sensors located on a 1996 chevy cavelier and are there any diagrams available for replacing them


The crankshaft sensor is located just to the side of your ignition coil pack on the engine block. The camshaft sensor is located on the back of the engine, just to the left of the oil filter. I would HIGHLY suggest having a qualified technician do this job for you. There is only one 10mm head bolt holding the sensor into the block, but these sensors are know to freeze into the engine block and break leaving a part of the sensor in the engine. If you attempt this yourself, be sure to rotate the sensor once the bolt is removed, and pull GENTLY. If it breaks, your in for a large repair bill.

Aug 14, 2012 | Chevrolet Cavalier Cars & Trucks

1 Answer

Where is the camshaftsensor on a1996 ford explorer with a 4.0


1996 Ford Truck Explorer 4WD 4.0L EFI 6cyl the Camshaft Position Sensor is located: Under hood, center, rear engine area,mounted on center upper rear of engineblock

Remember to rate this and comment.

Sep 13, 2010 | 1996 Ford Explorer

1 Answer

Whereisthecrankpositionsensorlocatedon1996truck


1996 Chevrolet Truck S10 P/U 4WD 4.3L SFI 6cyl
The Crankshaft Position Sensor is located under hood, center, front engine area, rear of crankshaft pulley, mounted in engine block;

The Camshaft Position Sensor is located under hood, center, rear engine area, mounted inside distributor.

Hope this help (remember rated this help).

Feb 08, 2010 | 1996 Chevrolet S-10 Pickup

1 Answer

1996 chevy tahoe 4wd LT 4Door 5.7L Vortec. Truck will not start, the starter grinds VERY loudly. Replaced starter several times, battery is good, replaced crank position sensor. Possible pre ignition? ...


i suggest removing the flywheel inspection cover, and rolling the engine over a little bit at a time, checking to make sure that there are no worn or broken teeth. also, make sure there is no lateral movement, which could indicate a broken flexplate. good luck.

Dec 08, 2009 | 1996 Chevrolet Tahoe

1 Answer

Timing specs on a 1996 chevy tahoe LS 4wd 5.7 and also the scanner said number 1 and 4 have a random missfire but it wont throw a code


timing is about 5-7 deg btdc and if it is throwing misfire codes. i would suggest using only ac delco spark plugs to avoid this issue.

Nov 09, 2009 | 1996 Chevrolet Tahoe

1 Answer

Where is the distributor located on a 1999 5.3L chevy vortec engine


There is no distributor. Firing is controlled by the computer which gets signals from crankshaft position sensor and camshaft position sensor for firing and timing.

Apr 29, 2009 | 2000 Chevrolet Tahoe

1 Answer

2004 Chevy Avalanche seats go in a 1996 Chevy Tahoe


The front seats I know will work but as far as the back seats they wont because the shape of the truck..

Nov 18, 2008 | 1996 Chevrolet Tahoe

Not finding what you are looking for?
1996 Chevrolet Tahoe Logo

Related Topics:

86 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

75744 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8123 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...