Question about Volkswagen Jetta

Open Question

Code P1128 #10 Long term fuel trim mult., bank 1 system too lean. 2000 jetta. how do i fix this problem?

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 1861 Answers

SOURCE: CHECK ENGINE LIGHT CAME ON P0171 FUEL TRIM BANK1 SYSTEM TO LEAN.

Hi. You need to clean the Mass Air Flow Sensor.
This is an easy job.
Get a can of throttle body or brake cleaner spray at your local auto parts store.

Open the hood, and locate the air filter box. follow the tube from the filter box towards the engine. Look for a small black box with 2 screws holding it to the air tube, Remove the wire connector and observe inside the sensor with a flashlight. You will see 2 small wires, and they will appear fuzzy or dirty. Spray the interior with the cleaner until the wires are nice and clean. Do not use compressed air, you will damage the sensor. Put it all back together and drive it.
This will def fix your issue. This is a vey common problem. If you do it yourself, you will save 70 + bucks.

Thanks for choosing FixYa, and a FIxYa rating for my assistance would be greatly appreciated.

Posted on Jan 23, 2009

  • 12 Answers

SOURCE: 2000 Chevrolet Truck S10 P/U 2WD 2.2L , loss of power

Your fuel pump is on it's way out, replace it before it stops completely.

Posted on Aug 08, 2009

  • 29 Answers

SOURCE: Fuel Trim System Lean Bank 1

Possible an exhaust leak, in the exhaust manifold above bank 1.

Posted on Dec 04, 2009

  • 2 Answers

SOURCE: 2001 trans am trouble code says fuel trim bank 2

check for intake manifold leak....had 2 go bad on me!

Posted on Mar 05, 2010

SOURCE: 2002 Ford Mustang GT I used OBD-II to get the

Because you got a misfire on cylinder #1 PO301
A misfire on cylinder #2 PO302
Misfires first 1000 rev PO316
O2 Codes PO 174
Etc,Etc


The LTT, is the result of not learning (yet-thus long term)
what isn't working correctly---Your Engine

Replace bad Coil--which ever is missing
Do not go by the codes,alone ,TEST

Posted on Dec 11, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

I have a PO171 code on my 1999 Jeep grand cherakee larado can You tell me how to fix it, Thank You.


  • Dale, code P0171 fuel system too lean
  • Possible causes
  • change fuel filter first, if it has not been done recently
RESTRICTED FUEL SUPPLY LINE
FUEL PUMP INLET STRAINER PLUGGED
FUEL PUMP MODULE
O2 SENSOR
O2 SENSOR SIGNAL CIRCUIT SHORTED TO GROUND
O2 SENSOR HEATER OPERATION
TPS VOLTAGE GREATER THAN 0.92 VOLTS WITH THROTTLE CLOSED
TP SENSOR SWEEP
MAP SENSOR OPERATION
ECT SENSOR OPERATION
ENGINE MECHANICAL PROBLEM
FUEL FILTER/PRESSURE REGULATOR (HIGH)
PCM
Check the attached links,
"I hope this helped you out, if so let me know by pressing the helpful button. Check out some of my other posts if you need more tips and info."

2000 Jeep Grand Cherokee p0171

Possible problems related to Code P0171 Jeep Garage Jeep Forum

P0171 System to Lean Bank 1

Code P0171

Mar 11, 2016 | Cars & Trucks

1 Answer

Keeps throwing up trouble codes p1506,p1151,p0302,p0171


Definition of Diagnostic Trouble Code P1506 Audi: Closed Throttle Position Switch Does Not Open/Short to Ground BMW: Idle-Speed Control Valve Opening Solenoid Control Circuit Signal High Ford: Idle Air Control Overspeed Error (see P0507) Jaguar: Idle Air Control System RPM Lower Than Expected - B Bank Kia: IAC Valve Opening Coil Voltage High Lincoln: Idle Air Control Overspeed Error (see P0507) Mazda: Idle Air Control Overspeed Error Mercury: Idle Air Control Overspeed Error (see P0507) Porsche: Throttle Jacking Unit Lower Mechanical Stop, Signal Implausible Volkswagen: Closed Throttle Position Switch Does Not Open/Short to Ground Volvo: IAC Valve Opening Signal
------------------------
Definition of Diagnostic Trouble Code P1151 Audi: Bank1, Long Term Fuel Trim, Range 1 Leanness Lower Limit Exceeded BMW: Oxygen Sensor Heater Circuit Signal Intermittent (Bank 2 Sensor 1) Ford: Lack Of Heated Oxygen Sensor Bank 2 Sensor 1 Switches - Sensor Indicates Lean Jaguar: Lack of H02S-21 switch, sensor indicates lean Land Rover: Lambda control limit bank 2.Implausible signal/condition Lincoln: Lack Of Heated Oxygen Sensor Bank 2 Sensor 1 Switches - Sensor Indicates Lean Mazda: Lack Of Heated Oxygen Sensor Bank 2 Sensor 1 Switches - Sensor Indicates Lean Mercury: Lack Of Heated Oxygen Sensor Bank 2 Sensor 1 Switches - Sensor Indicates Lean Subaru: HO2S-12 Heater Circuit High Input Toyota: Coolant Path Clog Up for Coolant Heat Storage System Volkswagen: Bank1, Long Term Fuel Trim, Range 1 Leanness Lower Limit Exceeded
------------
Definition of Diagnostic Trouble Code P0302 Category: Powertrain Definition: Cylinder 2 Misfire DetectedNote: This definition of P0302 is applied to all manufacturers
--------------------------
Definition of Diagnostic Trouble Code P0171 Category: Powertrain Definition: System Too Lean Bank 1Note: This definition of P0171 is applied to all manufacturers

Jun 17, 2015 | Cars & Trucks

1 Answer

What is the fix for a code p0171 problem


Lean condition bank 1 refers to the computers interpretation of information delivered by the o2 sensor for bank 1. Possible causes are many. First look at the sensor readings. You should see a fluctuation of voltage readings. If the sensor is not fluctuating it should set another code with it. The readings should be .05 v to about .455 volts normally. If the readings are lean then look at the fuel trims. They will likely be nowhere near 0. When the engine is right, the trims may go positive 3 to negative 3. If your short term fuel trim is say +18 and the long term fuel trim is say +20 at idle then try runnung the engine at a steady 1600 rpm and wait a minute till the readings level out. If they approach 0 then look for a vacuum leak. Let the engine idle and use choke cleaner spray to find the leak. Spray suspect areas and watch for changes in fuel trims.

Aug 01, 2014 | 2000 Cadillac DeVille

1 Answer

Engine light on


P0171 ; Fuel Trim System Lean (Bank 1)
P0174; Fuel Trim too Lean (Bank 2)
fuel trim is system to modify injector pulse if system go lean it will go rich when the system is too much lean and is max.rich it code
look for 02 sensor bank 1 and 2 data
hope it helps

Mar 31, 2014 | 2003 Chevrolet Malibu

1 Answer

I have a 2006 Chevy Colorado..Check engine light on and code 171 came up. Oxygen sensor replaced as was gas cap..Still on..What else needs repairing to fix this??


Trouble Code: P0171

Fuel Trim Too Lean

Possible Causes:


The current cell can be observed using a scan tool.The system will go lean if an injector is not providing enough fuel.A lean condition could be present during high fuel demand due to a fuel pump not pumping enough fuel, plugged fuel filter or a restricted fuel line.Insufficient fuel in the tank or low fuel pressure may cause this DTC to set. Refer to Fuel System Diagnosis .Review the Failure Records with a scan tool. If an intermittent condition is suspected, refer to Intermittent Conditions .

Jan 16, 2013 | 2006 Chevrolet Colorado Extended

1 Answer

2007 Hyundai Entourage codes P2187, PP0174,P2189,P2195,P2270,P2272


I've come across these codes before. In almost every case there was an air leak in the intake air hose (hose between the engine air filter & the throttle body). Inspect this hose & tubes attached to it. This is especially true when the lean code includes the comment 'at idle'
P2187 - System too lean at idle Bank 1
P0174 - System too lean Bank 2
P2189 - System too lean at idle Bank 2
P2195 = HO2S Signal Biased/Stuck Lean (Bank 1 Sensor 1)
P2270 = HO2S Signal Stuck Lean (Bank 1 Sensor 2)
P2272 = HO2S Signal Stuck Lean (Bank 2 Sensor 2)

P2187 & P2189 = In order to provide the best possible combination of drivability, fuel economy and emission control, the PCM uses a closed loop air/fuel metering system. The PCM monitors the HO2S signal voltage and adjusts fuel delivery based in closed loop fuel control. Changes in fuel delivery will be indicated by the long-term and the short-term fuel trim values. The ideal fuel trim value is around 0%. The PCM will add fuel when the HO2S signal is indicating a lean condition. Additional fuel is indicated by fuel trim values that are above 0%. The PCM will reduce fuel when the HO2S signal is indicating a rich condition. Reduction in fuel is indicated by fuel trim values that are below 0%. The DTC relevant to fuel trim will be set when the amount reaches excessive levels because of a lean or rich condition

Aug 31, 2011 | 2008 Hyundai Entourage

1 Answer

Code p1295


iam posting the hyundai code list i have that the vehicle manufacturer lists

P1100 Manifold Absolute Pressure Sensor Range/Performance

P1102 Manifold Absolute Pressure Sensor Circuit Low Input

P1103 Manifold Absolute Pressure Sensor Circuit High Input

P1123 Lang Term Fuel Trim Adaptive Too Lean

P1124 Long Term Fuel Trim Adaptive Too Rich

P1127 Long Term Fuel Trim Multiplier Too Rich

P1128 Long Term Fuel Trim Multiplier Too Lean

P1134 HO2S Bank 1 Sensor 1 Transition Time Switch (Bank 1 Sensor I)

P1154 HO2S Bank 2 Sensor 1 Transition Time Switch (Bank 2 Sensor 1)

P1166 HO2S Bank 1 Sensor 1 Controller Adaptive Diagnosis Fault (Bank 1)

P1167 HO2S Bank 1 Sensor 1 Controller Adaptive Diagnosis Fault (Bank 2)

P1168 HO2S Bank 1 Sensor 1 Heater Power Incorrect (Bank 1 Sensor 2)

P1169 HO2S Bank 1 Sensor 1 Heater Power incorrect (Bank 2 Sensor 2)

P1372 Segment Time Incorrect

P1400 Manifold Differential Pressure Sensor Circuit

P1440 EVAP System Vent Solenoid Circuit

P1443 EVAP System Fault (Fuel Tank Cap Missing)

P1510 Idle Control Valve Opening Circuit Shorted (Coil 1)

P1511 Idle Control Valve Command Signal Shorted (Coil 2)

P1513 Idle Air Control Valve Opening Coil Circuit Open (Coil 1)

P1521 Power Steering Switch Input Circuit

P1529 Customer Snapshot Request VIA CAN

P1552 Idle Air Control Valve Closing Coil Circuit Shorted

P1553 Idle Air Control Valve Closing Coil Circuit Open

P1586 Encoding Signal Circuit Not Rationale

P1602 Serial Communication Fault with Transmission Control Unit

P1605 Rough Road Sensor Circuit

P1606 Rough Road Sensor Circuit Not Valid

P1611 MIL Request Signal Circuit Low Input

P1613 ECU Self-Test Failed

P1614 MIL Request Signal Circuit High Input

P1616 Main Relay Fault

P1623 Diagnostic Lamp Power Stage Fault

P1624 MIL On Request Signal//Cooling Fan Relay Low Circuit

P1625 Cooling Fan Relay High Circuit

P1665 Power Stage Group 'A' Fault
P1670 Power Stage Group 'B' Fault

Feb 10, 2011 | 2008 Hyundai Sonata

2 Answers

What is a STFT B1(%) -1.56. WHAT DOES THAT MEAN?


Here is some general information to get you started...
(I am quoting directly from several PDF sources, Googled).

STFT B1 = Short Term Fuel Trim Bank 1. This is the fuel correction percentage being used by the closed loop fuel strategy for Bank 1 (if a V style engine or for all cylinders if an inline engine). If the fuel system is in open loop, this number will be reported as 0%

Fuel trim refers to the feedback compensation value compared against the basic injection time. Fuel trim includes short–term fuel trim and long–term fuel trim.

Short–term fuel trim is the short–term fuel compensation used to maintain the air–fuel ratio at its ideal theoretical value. The signal from the heated oxygen sensor indicates whether the air–fuel ratio is RICH or LEAN compared to the ideal theoretical value, triggering a reduction in fuel volume if the air–fuel ratio is rich, and an increase in fuel volume if it is lean.

Long–term fuel trim is overall fuel compensation carried out long–term to compensate for continual deviation of the short–term fuel trim form the central value due to individual engine differences, wear over time and changes in the usage environment.

If both the short–term fuel trim and long–term fuel trim are LEAN or RICH beyond a certain value, it is detected as a malfunction and the check engine warning (CHK ENG) lights up.

If the total of the short–term fuel trim value and long–term fuel trim value is within ± 25 %, the system is functioning normally.

Apr 07, 2010 | 1998 Jeep Grand Cherokee

1 Answer

Speedometer sudenly stoppped working. now works intermittently. also shows check engine light. It is showing p0171 & p0172 codes. Lean and rich. seams like they contradict each other. occasionaly the...


P0171 indicates a lean condition. The most common cause of this is a defective mass air flow sensor. Also check if any vacuum leaks.Replace MAf sensor,if cleaning the MAF does not help.
OBD II P0172 Fuel System Too Rich (Bank 1).P0172 - System Too Rich (Bank 1) Essentially this DTC means that an oxygen sensor in bank 1 detected a rich condition.
When the code says that the Fuel System is "too rich," it means that the computer has been subtracting more and more fuel, which is called Long Term Fuel Trim. Ideally, the Long Term Fuel Trim should be close to 1 to 2 percent. When a code P0172 is set, it means that the Fuel Trim is anywhere from -15 percent to as low as -30 percent compensated. When this happens, the computer knows that there is an improper condition in the control of the Fuel System.


Thanks.

Feb 07, 2010 | 1996 Volvo 850

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

38 people viewed this question

Ask a Question

Usually answered in minutes!

Top Volkswagen Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

yadayada
yadayada

Level 3 Expert

75797 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8140 Answers

Are you a Volkswagen Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...