Question about Mitsubishi Mighty Max

Open Question

Need to know how to place the timing belt on 1992 mitsubishi mightymax truck

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 119 Answers

SOURCE: How to set a timing belt for a 1992 GEO Storm

Here you are:

137fd9e.png

Posted on Jun 01, 2008

AUTODOC01
  • 216 Answers

SOURCE: need to know the timing marks on 1992 toyota

you may find them online but if it were me i would go to local auto parts and spend the $24.95 on a haynes repair manual it has pictures of the marks and the tension specs etc worth the $$ , remove #12 spark plug and take a peice of wire stick it into the hole till it touchs the piston then rotate the crankshaft till its a top dead center then look down at the line up marks behind the crank gear they should line up then rotate the camshaft till marks line up should be 12 oclock on cam gear? this is sometimes tricky to get it lined up without it being 1 tooth off thats why picture is best ? hope this helps autodoc01@live.com

Posted on Aug 27, 2009

  • 144 Answers

SOURCE: Timing belt installation

Good afternoon! Ive got you covered on this one! Have a great weekend!! I have enclosed figures for the diesel engine,the 8 valve gas and 16 valve gas. yours should be the 16 valve configuration as you will see in the figures.a3c1ad4.gifaf8e237.gifbc25dec.gif021398e.gif00bd376.gif5a4b57b.gif

Posted on Sep 25, 2009

  • 1757 Answers

SOURCE: Timing belt was removed, need to know timing belt

Sorry for the severe delay.
I am personally going back to answer your unanswered question.
I do not know if you still need the answer, but I am going to answer it in case you still do.

Click on the following direct Link. It has the Timing Belt Diagrams that you will need. Plus additional Instruction and Directional Diagrams you should use.
Again my apologies...
Let me know if this helped, or if you have additional information or questions. Feel Free to contact me at FixYa.com!

http://www.2carpros.com/car_repair_information/year/1988/make/mitsubishi/model/pickup/1988_mitsubishi_pickup_timing_belt_diagram_marks.htm

Posted on Mar 27, 2010

  • 2002 Answers

SOURCE: I have a 1993 Mitsubishi Mightymax 2.4 L4 and i

If your engine is running after you changed the timing belt then you need a timing light to adjust timing at this point. The specifications should be on the emission sticker under the hood. Hope this helps.

Posted on Oct 07, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I broke my timing belt on a 1994 mightymax and want to know if i can just put new belt on or did i bend valves


no they dont clear they hit the piston. it all depends on how fast the engine was running to how much damage has been done. sometimes it can just be a bent valve. or a set of them. or at worst the pistons are damaged. on some occasions it would just be a auto adjuster damaged you will not be able to tell till the new belt is fitted. will tap alot.

Apr 02, 2013 | 1994 Mitsubishi Mighty Max

2 Answers

I have a 1993 Mitsubishi Mightymax 2.4 L4 and i just replaced the timing belt. I need a diagram or something of the sort to adjust the timing, as i have already done by ear but isn't completely...


if you done it by ear --ie turning the distributor then you are not far out akthough a professional mechanic might get it a bit better i mean by this a old school mechanic but if your in doubt then use a timing light and set timing to to about 6 to 8 degrees before TDC depending on the compression ratio and fuel used ,an old GT type engine can be as high as 12 or 16? running on 101 octane fuel but a newer vehicle running on 91 unleaded will be around 6? maybe even 4? ,The octane rating is the amount of additive used to prevent pre detonation of the fuel but certain refineries sell this low grade low octane fuel that isnt of the same standard and the flame rate when it burns is a lot lower and also the carbon it produces when it burns is greater .no if it sounds ok and doesnt pink or overheat then leave well alone

Oct 06, 2011 | 1993 Mitsubishi Mighty Max

1 Answer

How to replace water pump in a 1992 mitsubishi galant


All Mitsubishi cars pretty much hide the water pump under the timing belt. You should buy all new belts for the car and consider replacing the water pump at the same time.You will have to take off the power steering belt, the alternator belt, the upper belt cover, support the motor, take off the motor mount, jack up the right front corner of the car, take off the front right tire, take off the engine plastic under cover, line up the TDC timing mark, Take off the front wheel ,take off the plastic splash cover, using an air wrench take off the lower pulleys, take off the lower engine cover, observe the timing marks/arrows and highlight with paint (on the crankshaft,counter balancer shaft , and cam shaft),take off the timing belt, counter balancer belt if there is one, water pump belt, and now you can unbolt the water pump, scrape the gasket, and replace it. Now the good news, if you have tools,a compressor, an air gun(for lower pulley bolt), patience , and four to eight hours to kill, you can actually do it your self.

Nov 12, 2010 | 1992 Mitsubishi Galant

1 Answer

I need a diagram of timing belt for 1991 mitsubishi gto non torbo


here it is let me know ist the wrong one, i cand send it to you also, im not sure which motor you have on that car theres 4 diffrent engines, this is the most common but be sure., its the V6
DONT FORGET TO SEND ME A FEEDBACK OR A TESTIMONIAL THANSK ebaf001.gif

Aug 02, 2010 | 1992 Mitsubishi Diamante

1 Answer

My sister has a mitsubishi expo 1993 and the time belt got destroy my nephew toke it a part and now we don't know how to put it back can you tell me how thanks


you may have damaged your valves when the belt broke.
You will need to find ou the timing marks for the cam gear or gears as well as the timing mark for the crankshaft because if they are not lined up properly it will not start and if it does you could do damage to your valves if they arent already damaged

Jun 09, 2010 | 1992 Mitsubishi Expo

1 Answer

My timing is off


Sorry for the delay. I am personally going back to answer your unanswered question.
I do not know if you still need the answer, but I am going to answer it in case you still do.
Click on the following direct Link. It has the Timing Belt Diagrams with Marks for the Camshaft and Crankshaft that you will need.

Again my apologies...
Let me know if this helped, or if you have additional information or questions. Feel Free to contact me at FixYa.com!


http://www.2carpros.com/car_repair_information/year/1992/make/mitsubishi/model/pickup/1992_mitsubishi_pickup_timing_belt_diagram_marks.htm

Dec 16, 2009 | 1992 Mitsubishi Mighty Max

1 Answer

New timing belt keeps getting loose when it cools down


yes you can get defective auto tenioners.Chage ASAP.

May 30, 2009 | 1992 Mitsubishi 3000GT

1 Answer

Need emmision vacumm diagram for 1988 mighty max or pickup--2.0


I have a factory manual for a 1985 MightyMax if that would help. I could send the section that you need.

Sep 25, 2008 | 1985 Mitsubishi Mighty Max

1 Answer

Timing belt


  • IF your doing your own timing belt, you need to get a Chilton's Repair manual on your particular car, it has the information you need. If you have never done one before, I suggest taking it to a shop, as you can cause severe engine damage if you do NOT get the timing belt on in the correct place.... what can happen is you can cause your engine valves to get bent because you didn't get it timed correctly. This problem happens alot with novices trying to repair timing issues and dont' know what they are doing.

Sep 21, 2008 | 2000 Mitsubishi Mirage

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

673 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mitsubishi Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8210 Answers

Are you a Mitsubishi Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...