Question about Ford Taurus

1 Answer

I've got a Taurus SEL, 2003 and have a broken rubber boot on the left tie rod arm, from the steering gear, vent line was not connected and have a pulsing in front end while stopping vehicle?

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 492 Answers

The tie rod may have a loose end but the pulsing usually is from warped disc rotors. I would check out the front end checked out for safety's sake.

Posted on Mar 19, 2011

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Diagram for power steering lines for 2000 cougar


68e1a5de-4810-4a60-b60b-447d3a6d5e84.gif
Item Part Number Description 1 Fluid reservoir 2 Steering wheel 3 Steering column assembly 4 Flexible coupling 5 Tie-rod end 6 Tie-rod 7 Steering gear boot 8 Steering gear 9 Fluid cooler 10 Steering gear hoses 11 Power steering pump

Sep 26, 2014 | 2000 Mercury Cougar

1 Answer

Bar that should be connected to front driver side wheel, it is broken off .approx.4-6 inches from the wheel, and I need to know for sure what the bar is


2002 Chevy Monte Carlo; connected to wheel (or steering knuckle) is:
-lower control arm, connects from frame to bottom of knuckle
-tie rod end, connects from steering gear to knuckle
-sway bar link, connects from strut to lower control arm

Nov 11, 2013 | 2002 Chevrolet Monte Carlo

2 Answers

Where is the outer tie rod on left side located


It is connected to the left steering knuckle (behind the left front wheel). Very difficult to see without removing the wheel.

Mar 06, 2011 | Chevrolet Lumina Cars & Trucks

1 Answer

My rack and pion is leaking , how do i replace


To Remove:
  1. Before servicing the vehicle, refer to the precautions at the beginning of this section. NOTE: The wheels of the vehicle must be straight ahead and the steering column in the LOCK position before disconnecting the steering column or intermediate shaft from the steering gear. Failure to do so will cause the SIR coil assembly (clock spring) to become uncentered, which may cause damage to the assembly.
  2. Lock the steering column by installing the J42640 into the underside of the steering column.
  3. Raise and support the vehicle.
  4. Remove the tires and wheels.
  5. Remove the power steering gear heat shield.
  6. Remove or disconnect the following: CAUTION
    Failure to disconnect the intermediate shaft from the rack and pinion stub shaft can result in damage to the steering gear and/or intermediate shaft. This damage can cause loss of steering control, which could result in personal injury.
    • Intermediate shaft lower pinch bolt and coupling from gear
    • Pressure and return pipes from the gear
    • Electrical connector, if equipped
      Stabilizer shaft links at lower control arms
    • Remove the left stabilizer shaft insulator.
    • Rotate the stabilizer shaft to access steering gear bolts.
    • The outer tie rod retaining nuts.
    • Using J24319-B separate the outer tie rods from the steering knuckles.
    • Rack and pinion attaching bolts
    • Rack and pinion assembly through the left wheel opening.
  7. Transfer the outer tie rods if replacing the power steering gear.
To Install:
  1. Install or connect the following:
    • Rack and pinion assembly through the left wheel opening and tighten the bolts to 70 ft. lbs. (95 Nm)
    • Electrical connector, if equipped
      Pressure and return lines to the steering gear and tighten the fittings to 22 ft. lbs. (30 Nm)
    • Heat shield and bolts. Tighten the bolts to 7 ft. Lbs. (10 N)
    • Install the left stabilizer shaft insulator.
  2. Install stabilizer shaft Links to lower control arms
  3. Intermediate shaft to the steering gear and tighten the pinch bolt to 35 ft. lbs. (47 Nm)
  4. Install the outer tie rods to the steering knuckles.
  5. Install the outer tie rods retaining nuts. torque the nuts to 22ft.lbs(30 Nm) plus an additional 180 degrees.
  6. Install the tires and wheels.
  7. Lower the vehicle.
  8. Remove the steering column anti rotation pin from the steering column.
  9. Fill and bleed the power steering system.
  10. Adjust the front toe.

Lock the steering column by installing the Steering Column Anti Rotation Pin tool J 42640 into the underside of the steering column--Aurora

tecnovative_120.gif
Steering gear mounting bolts--Aurora



tecnovative_121.gif
Power Rack & Pinion Steering Gear Heat Shield Removal & Installation To Remove:
  1. Raise and support the vehicle.
  2. Remove or disconnect the following:
    • The stabilizer shaft links.
    • Rotate the stabilizer shaft downward.
    • The electrical harness clip.
    • Power steering gear heat shield mounting bolts.
    • The heat shield.
To Install:
  1. Install the power steering gear heat shield.
  2. Install or connect the following:
    • The mounting bolts And torque to 89in.lbs.(10 Nm)
    • The electrical harness clip.
    • Rotate the stabilizer shaft into position.
    • The stabilizer shaft links.
  3. Lower the vehicle.
Figure of heat shield removed from above rack bolts with location shown

tecnovative_122.gif

Feb 11, 2011 | 2001 Oldsmobile Aurora

1 Answer

STeering wheel is loose and noisy while steering. Sounds like something broke inside.


This might help to understand the steering linkage: REMOVAL & INSTALLATION Fig. 1: Steering linkage used on the Bronco and 4-wheel drive F-150 84928067.gif
Fig. 2: Steering linkage used on the 4-wheel drive F-350 84928070.gif
Fig. 3: Steering linkage used on F-Super Duty chassis/cab 84928071.gif
Pitman Arm EXCEPT F-SUPER DUTY STRIPPED CHASSIS AND MOTOR HOME CHASSIS
  1. Place the wheels in a straight-ahead position.
  2. Disconnect the drag link at the Pitman arm. You'll need a puller such as a tie rod end remover.
  3. Remove the Pitman arm-to-gear nut and washer.
  4. Matchmark the Pitman arm and gear housing for installation purposes.
  5. Using a 2-jawed puller, remove the Pitman arm from the gear.
  6. Installation is the reverse of removal. Align the matchmarks when installing the Pitman arm. Tighten the Pitman arm nut to 170-230 ft. lbs. (230-312 Nm); torque the drag link ball stud nut to 50-75 ft. lbs. (68-102 Nm), advancing the nut to align the cotter pin hole. Never back off the nut to align the hole.
F-SUPER DUTY STRIPPED CHASSIS MOTOR HOME CHASSIS
  1. Matchmark the Pitman arm and sector shaft.
  2. Disconnect the drag link from the Pitman arm.
  3. Remove the bolt and nut securing the Pitman arm to the sector shaft.
  4. Using a 2-jawed gear puller, remove the Pitman arm from the sector shaft. To install:
  5. Aligning the matchmarks, slide the Pitman arm onto the sector shaft. If the arm won't slide on easily, use a cold chisel to spread the separation. NEVER HAMMER THE ARM ONTO THE SHAFT! Hammering on the arm will damage the steering gear!
  6. Install the nut and bolt. Tighten the nut to 220-300 ft. lbs. (298-407 Nm).
  7. Connect the drag link.
Tie Rod and Drag Link EXCEPT RUBBERIZED BALL SOCKET LINKAGE
  1. Place the wheels in a straight-ahead position.
  2. Remove the cotter pins and rust from the drag link and tie rod ball studs.
  3. Remove the drag link ball studs from the right-hand spindle and Pitman arm.
  4. Remove the tie rod ball studs from the left-hand spindle and drag link.
  5. Installation is the reverse of removal. Seat the studs in the tapered hole before tightening the nuts. This will avoid wrap-up of the rubber grommets during tightening of the nuts. Tighten the nuts to 70 ft. lbs. (95 Nm). Always use new cotter pins.
  6. Have the front end alignment checked.
RUBBERIZED BALL SOCKET LINKAGE
  1. Raise and support the front end on jackstands.
  2. Place the wheels in the straight-ahead position.
  3. Remove the nuts connecting the drag link ball studs to the connecting rod and Pitman arm.
  4. Disconnect the drag link using a tie rod end remover.
  5. Loosen the bolts on the adjuster clamp. Count the number of turns it take to remove the drag link from the adjuster. To install:
  6. Installation is the reverse of the removal procedure. Install the drag link with the same number of turns it took to remove it. Make certain that the wheels remain in the straight-ahead position during installation. Seat the studs in the tapered hole before tightening the nuts. This will avoid wrap-up of the rubber grommets during tightening of the nuts. Tighten the adjuster clamp nuts to 40 ft. lbs. (54 Nm). Tighten the ball stud nuts to 75 ft. lbs. (102 Nm).
  7. Have the front end alignment checked.
Connecting Rod RUBBERIZED BALL SOCKET LINKAGE
  1. Raise and support the front end on jackstands.
  2. Place the wheels in the straight-ahead position.
  3. Disconnect the connecting rod from the drag link by removing the nut and separating the two with a tie rod end remover.
  4. Loosen the bolts on the adjusting sleeve clamps. Count the number of turns it takes to remove the connecting rod from the connecting rod from the adjuster sleeve and remove the rod.
  5. Installation is the reverse of removal. Install the connecting rod the exact number of turns noted during removal. Tighten the tie rod nuts to 40 ft. lbs. (54 Nm); the ball stud nut to 75 ft. lbs. (102 Nm).
  6. Have the front end alignment checked.
Tie Rod Ends RUBBERIZED BALL SOCKET LINKAGE Fig. 4: Remove the cotter pin from the castellated nut at the ball stud 88288p02.jpg
Fig. 5: Remove the nut from the ball stud 88288p03.jpg
Fig. 6: Use a tie rod end puller tool to remove the ball stud from the Pitman arm 88288p04.jpg
Fig. 7: Liquid correction fluid makes excellent paint to mark the threads of the tie rod end 88288p05.jpg
Fig. 8: For a more accurate reinstallation, you may measure the tie rod end prior to removal 88288p06.jpg
Fig. 9: After having loosened the nut, unscrew and remove the tie rod end 88288p07.jpg
  1. Raise and support the front end on jackstands.
  2. Place the wheels in a straight-ahead position.
  3. Remove the ball stud from the Pitman arm using a tie rod end remover. NOTE: Optional: paint a mark or measure the length of the tie rod end threads to ease reinstallation in as close to the original position as possible.
  4. Loosen the nuts on the adjusting sleeve clamp. Remove the ball stud from the adjuster, or the adjuster from the tie rod. Count the number of turns it takes to remove the sleeve from the tie rod or ball stud from the sleeve. To install:
  5. Install the sleeve on the tie rod, or the ball in the sleeve the same number of turns noted during removal. Make sure that the adjuster clamps are in the correct position, illustrated, and torque the clamp bolts to 40 ft. lbs. (54 Nm).
  6. Keep the wheels facing straight-ahead and install the ball studs. Tighten the nuts to 75 ft. lbs. (102 Nm). Use new cotter pins.
  7. Install the drag link and connecting rod.
  8. Have the front end alignment checked.
prev.gif next.gif

Sep 18, 2010 | 1996 Ford F150 Regular Cab

1 Answer

Power steering going bad,need info about rackard pinion


you can buy remanufactured at parts store or buy used from car-part.com. page with * is lowest cost.

It's a pretty big job for a novice.

here's 96 taurus steps with 3.8l engine. don't have 94. should be similar

Removal
SPECIAL SERVICE TOOL(S) REQUIRED Tool Number Description T94T-6000-AH Exhaust Connector Holder Tool T57L-500-B Bench Mounted Holding Fixture
  1. Disconnect negative battery cable.
  1. Position steering wheel one-half turn to right and lock wheel.
  1. Position steering column boot out of the way. Remove pinch bolt retaining steering column intermediate shaft coupling to power steering short rack and separate.
  1. Disconnect PCV vent tube and vacuum supply hose from clean air tube. Loosen two hose clamps retaining clean air tube and position out of the way.
  1. Disconnect power steering auxiliary actuator and power steering pressure switch.
  1. Remove two heat shield pushpin retainers from power steering hose bracket and remove heat shield.
  1. Remove one retaining bolt from left turn pressure hose bracket.
  1. Position drain pan under steering gear.
  1. Remove power steering pressure and return hoses from fittings on power steering rack. Position both hoses out of the way. Disconnect rear HO2S connector at steering rack and position out of the way.
  1. Partially raise vehicle.
  1. Remove front wheel and tire assemblies.
  1. Remove LH upper stabilizer bar link retaining nut and position link out of the way.
  1. Loosen LH tie-rod jam nut. Remove cotter pin and tie-rod retaining nut at lower control arm. Using tie-rod end separator or equivalent, remove tie-rod from control arm and from steering gear.
  1. Loosen RH tie-rod jam nut. Remove cotter pin and tie-rod retaining nut at lower control arm. Using tie-rod end separator or equivalent, remove tie-rod from control arm and from steering gear.
  1. Raise vehicle.
  1. Remove drain pan.
  1. Remove two steering gear retaining nuts at front subframe.
  1. Install Exhaust Connector Holder Tool T94T-6000-AH on flex tube.
  1. Remove bolts, nuts, and gasket from where flex tube and converter Y-pipe connect. Separate tube from pipe.
  1. Position Rotunda Power Train Lift 014-00765 or equivalent with wood blocks approximately 1016 mm (40 inches) in length (secured to lift) under subframe and raise.
  1. Remove two rear subframe retaining bolts and lower subframe approximately 102 mm (4 inches).
  1. Rotate power steering rack to clear bolts from subframe and remove assembly through LH wheel well.
  1. Remove two bolts retaining power steering hose bracket to short rack and remove bracket.
  1. Mount steering gear assembly in Bench Mounted Holding Fixture T57L-500-B.
  1. Remove four clamps retaining bellows to steering gear and tie-rods. Remove bellows and power steering gear rack tube.
  1. Position rack and pinion steering gear so several steering gear teeth are exposed. Hold steering gear with adjustable wrench on end teeth only, while loosening inner tie-rods. Remove tie-rods from steering rack. Remove steering rack from bench-mounted holding fixture.
Installation
  1. Mount new steering gear assembly in Bench Mounted Holding Fixture T57L-500-B.
  1. Position rack and pinion steering gear so several steering gear teeth are exposed. Hold steering gear with adjustable wrench on end teeth only, while tightening inner tie-rods. Tighten to 90-110 Nm (66-81 lb-ft).
  1. Apply Steering Gear Grease C3AZ-19518-A meeting Ford specification ESB-M1C119-A to groove in connecting rods where tie-rod bellows clamp to front wheel spindle tie-rod and uniformly apply to inner diameter of bellows. Install bellows and gear rack tube onto short rack.
  1. Install new inner and outer bellows clamps.
  1. Remove steering gear from Bench Mounted Holding Fixture and place on bench.
  1. Install power steering hose bracket and retaining bolts at top of steering gear. Tighten to 9-12 Nm (80-106 lb-in).
  1. Install steering gear retaining bolts in steering gear housing and install short rack through LH wheel well.
  1. Position steering rack and retaining bolts through subframe. Raise powertrain lift until rear subframe contacts body and install retaining bolts. Tighten to 135-195 Nm (100-144 lb-ft). Lower and remove powertrain lift from vehicle.
  1. Install power steering short rack-to-subframe nuts. Tighten to 97-132 Nm (72-97 lb-ft).
  1. Install new gasket, bolts and nuts at converter Y-pipe and flex tube. Tighten to 34-46 Nm (26-34 lb-ft).
  1. Remove flex tube holder.
  1. Partially lower vehicle.
  1. Install LH jam nut and outer tie-rod to inner tie-rod. Install tie-rod to steering knuckle. Install retaining nut. Tighten to 47-63 Nm (35-46 lb-ft). Install new cotter pin.
  1. Install LH stabilizer bar link and retaining nut. Tighten to 76.5-103.5 Nm (57-76 lb-ft).
  1. Install RH jam nut and outer tie-rod to inner tie-rod. Install tie-rod to steering knuckle. Install retaining nut. Tighten to 47-63 Nm (35-46 lb-ft). Install new cotter pin.
  1. Install tire and wheel assemblies. Tighten to 115-142 Nm (85-105 lb-ft).
  1. Lower vehicle.
  1. Remove old Teflon® O-rings from pressure and return hoses. Install new Teflon® O-rings on pressure and return hoses.
  1. Install power steering pressure hose and return hose to fittings on power steering short rack. Tighten to 33-41 Nm (24-30 lb-ft).
  1. Install one retaining bolt to left-turn pressure hose bracket. Tighten to 9-12 Nm (80-106 lb-in).
  1. Connect rear HO2S connectors, power steering auxiliary actuator, and power steering pressure switch electrical connectors.
  1. Position heat shield at power steering hose bracket and install pushpin retainers.
  1. Install clean air tube, connect PCV vent tube and vacuum supply hose, and tighten hose clamps. Tighten to 2-3 Nm (18-27 lb-in).
  1. Install steering column intermediate shaft coupling to power steering short rack and install pinch bolt. Tighten to 41-51 Nm (30-38 lb-ft). Position steering column boot over steering rack.
  1. Fill and purge system.
  1. Check operation.
  1. Adjust only toe for alignment. Refer to Section 04-00 .

Aug 05, 2009 | 1994 Ford Taurus

1 Answer

Need an digram of 2000 ford focus power steering pump


cfef959.gif
Item Part Number Description 1 - Steering wheel 2 - Steering column 3 - Boot 4 - Tie-rod 5 - Tie-rod end 6 - Steering gear 7 - Steering gear to fluid cooler hose 8 - Fluid cooler 9 - Power steering pressure (PSP) switch 10 - Power steering pump 11 - Fluid supply hose 12 - Fluid reservoir 13 - Pump to steering gear pressure line 14 - Steering gear pinion extension

Jul 30, 2009 | 2000 Ford Focus

1 Answer

I need a suspension diagram that shows the Inner tie rods.


The inner tie rods are screwed into ends of the steering rack assembly.

Look at this diagram. #6 is the rubber boots and #7 is the shaft from the inner tie rods.


http://www.anubiscycle.com/fixya/2000-windstar-steering-gear.jpg

Jun 08, 2009 | 2000 Ford Windstar

2 Answers

How to change inner tie rod ends?


if fluid is flowing out the bellows, you need to replace the steering rack assembly. There is no fluid in the area of the inner tie rod. The seal is just before the tie rod.

Steering Gear
The power rack and pinion steering gear is serviced as a power steering short rack (3L547). The front wheel spindle tie rods (3280) and tie rod ends (3A130) are serviced individually. -------------------------------------------------------------------------------------------
  • The power rack and pinion steering gear incorporates quick connect fittings for the power steering pressure hose (3A719) and power steering return hose (3A713) that allow the lines to swivel. This is normal and does not indicate loose fittings.
  • If the fittings leak, check to make sure they are tightened to 14-20 Nm (10-14 lb-ft). Do not overtighten.
  • If the leak is not corrected, replace the fitting seals.
-------------------------------------------------------------
f12ee38.gif
-----------------------------------------------------
Section 11-02: Steering System, Power 1997 Windstar Workshop Manual
REMOVAL AND INSTALLATION Tie Rod End Steering Gear Installed
Removal
  1. Remove and discard cotter pin and nut from worn tie rod end (3A130).
  1. Disconnect tie rod end from front wheel knuckle (3K185), using Tie Rod End Remover TOOL-3290-D or equivalent.
  1. Hold tie rod end with a wrench and loosen tie rod end jam nut.
  1. Note depth to which tie rod end was located by using the jam nut as a marker. Grip tie rod end with a pair of suitable pliers and remove tie rod end from front wheel spindle tie rod (3280).
---------------------------------------------------------------------------------------
11-02: Steering System, Power 1997 Windstar Workshop Manual
REMOVAL AND INSTALLATION Steering Gear Removal
  1. Raise vehicle on a twin post hoist and remove wheel and tire assemblies. Refer to Section 00-02 .


    13b4d70.gif

  1. Support vehicle with jackstands under front jack pads.
  1. Remove tie-rod end cotter pins and nuts and remove tie rod ends (3A130) from front wheel knuckle (3K185). Refer to Section 04-01 .
  1. Remove front stabilizer bar (5482). Refer to Section 04-01 .
  1. Disconnect heated oxygen and catalyst monitor sensors.
  1. Support flex pipe.
  1. Remove bolts and disconnect flex pipe from the converter.
  1. Raise dash opening steering column opening weather seal (3513) (secondary) above the steering gear housing (3548).
  1. Remove pinch bolt retaining steering column intermediate shaft coupling (3A525) to power steering gear input shaft and control (3D517) and disconnect the shaft.
  1. Remove nuts from steering gear-to-front subframe retaining bolts. Remove bolts.
  1. Remove rear subframe-to-body retaining bolts.
  1. Lower twin post hoist carefully until rear of subframe (5R003) separates from body, approximately four inches.
  1. Remove heat shield band and fold shield down.
  1. Rotate power rack and pinion steering gear to clear bolts from front subframe (5C145) and pull left to facilitate line fitting removal.
  1. Place a drain pan under vehicle and remove line fittings.
  1. Remove power rack and pinion steering gear through LH wheel well.
  1. Remove and discard the O-rings.
Installation
  1. Install new Teflon® O-rings on line fittings as outlined.
  1. Place steering gear retaining bolts in steering gear housing.
  1. Install power rack and pinion steering gear through LH wheel well.
  1. Install power steering line fittings to power rack and pinion steering gear.
  1. Position power rack and pinion steering gear into front subframe.
  1. Install ******** heat shield.
  1. Install tie-rod ends to front wheel knuckle. Install nuts and new cotter pins. Refer to Section 04-01 .
  1. Install LH front stabilizer bar. Refer to Section 04-01 .
  1. Install steering gear to subframe mounting nuts. Tighten to 115-135 Nm (85-99 lb-ft).
  1. Raise hoist until rear subframe contacts body.
  1. Install rear subframe to body retaining bolts. Tighten to 113-153 Nm (83-112 lb-ft).
  1. Install exhaust system flex tube to dual converter Y pipe (5F250) and remove flex tube support.
  1. Connect heated oxygen and catalyst monitor sensors.
  1. Install tire and wheel assemblies. Tighten lug nuts (1012) to 115-142 Nm (85-104 lb-ft).
  1. Using a new pinch bolt, install the steering column intermediate shaft coupling on the power steering gear input shaft and control and the lower steering column shaft. Tighten the pinch bolt to 34-46 Nm (25-33 lb-ft).
  1. Position steering column opening weather seal (secondary) over the steering gear housing. Tighten nuts to 4.5-6.3 Nm (40-55 lb-in).
  1. Remove jackstands and lower vehicle.
  1. Fill power steering oil reservoir (3A697) with Premium Power Steering Fluid E6AZ-19582-AA or equivalent meeting Ford specification ESW-M2C33-F. Refer to Section 11-00 .
  1. Check system for leaks and proper operation.

Apr 15, 2009 | 1997 Ford Windstar

1 Answer

Leak at the tie rod where boot is


it is because rubers keep the grease if it is not fitted tight it makes leake you loose all lubrication greases.

Oct 28, 2008 | 1993 Ford Taurus

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

72 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

75797 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

fordexpert

Level 3 Expert

5495 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...