Question about 1995 GMC Safari

Open Question

How do you replace alternator bracket on a 1995 Safari. The bracket that holds the alternator and pulleys that mounts to the engine broke. how do you replace it.

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

emissionwiz
  • 75822 Answers

SOURCE: how do i remove the power steering pump from a

u need to get a special tool for pulling asnd installing the pump's pulley, as soon as you get the pulley off the pump is easy to remove, Autozone and Kragen loan this tool with acredit card secrity deposit.

Posted on Jul 26, 2009

cursealoud
  • 42 Answers

SOURCE: 1998 chrysler town & country 3.8l- how do i get

you dont have to take it off. remove the 2 15mm bolts and pry the bracket sideways w/ a prybar. This shortens your time. You most likely have a 90amp alternator so it should be small enough to slide through.

Posted on Jul 11, 2009

  • 104 Answers

SOURCE: How to remove broken bracket holding up alternator.

Have you taken off the pivot bolt or bolts at the bottom of the alternator? It might be a long single bolt or two short bolts where it attaches at the block.

Posted on Sep 07, 2009

  • 2002 Answers

SOURCE: the alternator broke off and broke the front

Call around your local scrap yards or auto salvage. With the engine size and year they should be able to fix you up with a new bracket for cheap. Some will even let you take it off yourself for a better price. Hope this helps.

Posted on Oct 12, 2009

greg_margo
  • 1959 Answers

SOURCE: My belt tensioner pulley broke at the bolt that

You should only remove the drive belt shield if you raise the car. Below are step-by-step instructions per the repair manual. Drive Belt Tensioner
Removal & Installation To Remove:

  1. Disconnect the negative battery cable.
  2. Raise and safely support the vehicle.
  3. Remove the drive belt shield at the right wheel well.
  4. Remove the drive belt.
  5. Remove the drive belt tensioner mounting bolt.
  6. Remove the drive belt tensioner.
To Install:
  1. Install the belt tensioner. Torque the mounting bolt to 21 ft. lbs. (28 Nm).
  2. Install the drive belt.
  3. Install the drive belt shield.
  4. Lower the vehicle.
  5. Connect the negative battery cable.



Posted on Oct 30, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2005 xl7. How can I adjust alternator?


remove battery neg lug first. do not yank off alternator wires! until
this step is done first, or boom fire or eat acid.

which engine, we cant guess them here.
my guess H27 v6, wrong the 3.6L


all belts covered on car. (accessory)

here is a real 2007 page
seem you get lost at step 7
right>?


26044119-eqsv1nhxqdz21u4tq0h4adgz-1-0.jpg the alternator is NOT adjustable
so why ask this?
the $4 FSM covers this.
under drive belt replacement.
Drive Belt Replacement


Removal Procedure

Remove the air cleaner assembly. Refer to Air Cleaner Assembly Replacement .

Install the engine support fixture. Refer to Engine Support Fixture .

Remove the engine mount strut bracket. Refer to Engine Mount Strut Bracket Replacement - Right Side .

Raise and support the vehicle. Refer to Lifting and Jacking the Vehicle .

Remove the engine splash shield. Refer to Engine Splash Shield Replacement - Right Side .

Remove the right side engine mount bracket. Refer to Engine Mount Bracket Replacement - Right Side .

Lower the vehicle.


Rotate the drive belt tensioner clockwise to release the drive belt tension.

Slide the drive belt off of the belt idler pulley (1).

Slowly release the drive belt tensioner.

Remove the drive belt from the accessory drive pulleys.
if the post was to remove alternator? is it
do above
then unbolt alt.
end guessing what you are doing....


26044119-eqsv1nhxqdz21u4tq0h4adgz-1-1.jpg

Jan 08, 2016 | Suzuki Cars & Trucks

1 Answer

Cant get alternator out of engine compartment


Hey all, found this for 3.3L engine.
3.3-mgkxnf303xgr2hvssd3liypr-1-0.jpg

May 06, 2017 | 1995 Plymouth Voyager

1 Answer

How to chg alternator on 2002 ford taurus 24v dohc 3.0


ctionsThings You'll Need
  • Flywheel holding tool
  • New alternator
  • Socket wrench set
  • Torque wrench
    • 1Determine which alternator your Ford Taurus will need. You'll want to be sure the new alternator is compatible with your Taurus's engine. Models made from 1986 to 1991 have a 2.5 L HSC, 3.0 L Vulcan or 3.8 L engine. The 2.5 L engine was dropped for 1992 to 1995 models, and post-1995 models will have a 3.0 L engine.
    • 2Disconnect the negative battery cable with a socket wrench. Release the tension on the accessory drive belt so that you can remove the drive belt from the pulley.
    • 3Take off the mounting bolt on the right side of the alternator with a socket wrench and remove the bracket for the power steering hose. Remove the mounting bolts on top of the alternator, the front passenger wheel and tire assembly and the front fender splash shield. Remove the alternator splash shield with a socket wrench and take off the inspection cover for the torque converter.
    • 4Mount a tool to hold the flywheel so you can remove the crankshaft pulley bolt and crankshaft pulley. Lower the alternator so you can unplug its electrical connections. Disconnect the crankshaft position sensor and Oxygen sensor connector. Remove the lower alternator mounting bolt and B+ connector nut to remove the alternator.
    • 5Install the new alternator assembly by reversing the above procedure. Use a torque wrench to tighten the B+ connector nut to 71 in. lbs. and the lower alternator bolt to 18 foot pounds. Torque the crankshaft pulley bolt to 74. foot pounds, the upper alternator bolts to 18 foot pounds and the nut for the power steering hose bracket to 13 foot pounds.


Read more: How to Replace the Alternator in a Ford Taurus ' eHow.com http://www.ehow.com/how_4506222_replace-alternator-ford-taurus.html#ixzz1ZdgFklse

Oct 01, 2011 | 2002 Ford Taurus

1 Answer

How do i replace an alt on an 97 Grand Voyager?


When you says ALT, I'm assuming that you are talking about ALTERNATOR...

REMOVAL & INSTALLATION
2.4L Engine
  1. Disconnect the negative battery cable.
  2. Remove the accessory drive belt.
  3. Unplug the push-in field wire connector from behind the alternator.
  4. Remove the B+ nut and wire from behind the alternator.
  5. Remove the nut securing the top of the alternator to the adjuster bolt (a.k.a T-bolt).
  6. Remove the alternator pivot nut and bolt, located below the alternator.
  7. Remove the alternator from the vehicle.
To install:
  1. Install the alternator into position on the vehicle's engine.
  2. Install, but do not tighten, the alternator pivot nut and bolt.
  3. Install the nut securing the top of the alternator to the adjuster bolt.
  4. Connect the B+ wire and tighten the retaining nut to 75 inch lbs. (9 Nm).
  5. Plug in the push-in field wire connector onto the back of the alternator.
  6. Install the accessory drive belt. Be sure the drive belt is correctly routed on the engine and correctly seated on all of the pulleys, especially the alternator.
  7. Adjust the drive belt and tighten the adjuster/locking bolt to 40 ft. lbs. (54 Nm).
  8. Tighten the pivot bolt to 40 ft. lbs. (54 Nm).
  9. Reconnect the negative battery cable.
  10. Verify the charging rate of the alternator.

3.0L Engine
  1. Disconnect the negative battery cable.
  2. Remove the windshield wiper/motor module assembly.
  1. Remove the accessory drive belt from the alternator.
  2. Remove the bolt securing the top of the alternator to the mounting bracket.
  3. Remove the bolt securing the bottom of the alternator to the lower pivot bracket.
  1. While holding the alternator, unplug the push-in field wire connector from behind the alternator.
  2. While holding the alternator, remove the B+ nut and wire from behind the alternator.
  3. Remove the alternator from the vehicle.
To install:
  1. Hold the alternator in position near the mounting bracket, then connect the B+ wire and tighten the retaining nut to 75 inch lbs. (9 Nm).
  2. Plug in the push-in field wire connector onto the back of the alternator.
  3. Place the alternator into position on the mounting bracket, then install the bolt securing the bottom of the alternator to the lower pivot bracket.
  4. Install the bolt securing the top of the alternator to the mounting bracket. Tighten the upper and lower alternator bolts to 40 ft. lbs. (54 Nm).
  5. Install the accessory drive belt. Be sure the drive belt is correctly routed on the engine and correctly seated on all of the pulleys.
  6. Install the windshield wiper/motor module assembly.
  7. Reconnect the negative battery cable.
  8. Verify the charging rate of the alternator.

3.3L and 3.8L Engines
  1. Disconnect the negative battery cable.
  2. Remove the windshield wiper/motor module assembly.
  3. Remove the accessory drive belt.
  4. Remove the bolt securing the top of the alternator mounting bracket to the engine air intake plenum.
  1. Remove the bolts securing the outside of the alternator mounting bracket to the alternator mounting plate.
  2. Remove the bolt securing the top of the alternator to the mounting bracket.
  3. Remove the alternator mounting bracket from the vehicle.
  4. Rotate the alternator toward the dash panel.
  5. Unplug the push-in field wire connector from behind the alternator.
  6. Remove the B+ nut and wire from behind the alternator.
  1. Remove the bolt securing the bottom of the alternator to the lower pivot bracket.
  2. Remove the alternator from the vehicle.
To install:
  1. Install the alternator into position on the vehicle's engine.
  2. Install the bolt securing the bottom of the alternator to the lower pivot bracket.
  3. Connect the B+ wire and tighten the retaining nut to 75 inch lbs. (9 Nm).
  4. Plug in the push-in field wire connector onto the back of the alternator.
  5. Rotate the alternator forward away from the dash panel.
  6. Install the alternator mounting bracket in position on the vehicle.
  7. Install the bolt to secure the top of the alternator to the mounting bracket.
  8. Install the bolts to secure the outside of the alternator mounting bracket to the alternator mounting plate.
  9. Install the bolt to secure the top of the alternator mounting bracket to the engine air intake plenum.
  10. Tighten all of the alternator mounting bolts to 40 ft. lbs. (54 Nm).
  11. Install the accessory drive belt. Be sure the drive belt is correctly routed on the engine and correctly seated on all of the pulleys.
  12. Install the windshield wiper/motor module assembly.
  13. Reconnect the negative battery cable.
  14. Verify the charging rate of the alternator.

Hope helps woth this, remember rated this help. Good luck.

Jul 08, 2010 | 1997 Plymouth Grand Voyager

1 Answer

Can you give me a copy to download a free copy of


GM Cavalier/Sunfire 1995-2000 Repair Guide
Water Pump - REMOVAL & INSTALLATION

2.2L Engine
  1. Disconnect the negative battery cable.
  2. Properly drain the cooling system into an approved container.
  3. Remove all accessory drive belts or the serpentine belt.
  4. Remove the alternator and bracket. For details, please refer to of this guide.
  5. Unscrew the water pump pulley mounting bolts and then pull off the pulley.
  6. Unfasten the mounting bolts, then remove the water pump.
  7. Using a putty knife, clean the gasket mounting surfaces.

645f4b6.jpg

Fig. 1: Location and mounting of the water pump on the 2.2L engine

fb24336.jpg

Fig. 2: If the pulley turns when you try to loosen the bolts, attach sockets and ratchets to two of the bolts, insert a prybar to hold the pulley in place and loosen the bolts - 2.2L engine


dfb0eb6.jpg
Fig. 3: Remove the pulley from the water pump


4b5e42b.jpg
Fig. 4: The water pump is retained by four bolts, remove them and...


a2c49f3.jpg
Fig. 5: ...remove the water pump from the engine


0ea1971.jpg
Fig. 6: Thoroughly clean the gasket mating surfaces on the engine block as well as...


96cdb47.jpg
Fig. 7: ...the water pump (if it is being reused)


e8dcc4a.jpg
Fig. 8: Always use a quality new gasket like this one from Fel-Pro®


To install:

  1. Place a 1/8 in. (3mm) wide bead of RTV sealant on the water pump sealing surface or install a new gasket, on models so equipped. Install the pump and tighten the retaining bolts to 18 ft. lbs. (25 Nm).
  2. Install the water pump pulley, then tighten the mounting bolts to 22 ft. lbs. (30 Nm).
  3. As outlined in , install the alternator and bracket.
  4. Install the drive belts or serpentine belt, as applicable.
  5. Fill the cooling system to the proper level.
  6. Connect the negative battery cable, then start the engine and check for leaks.
continue...

Nov 20, 2009 | 1998 Chevrolet Cavalier

1 Answer

How do you replace the alternator on a 2000ford contour



Removal & Installation

2.0L Engine
  1. Disconnect the negative battery cable.
  2. Remove air intake resonators.
  3. Remove the air cleaner-to-throttle body tube and the mass airflow sensor.
  4. Unplug the connectors and remove the cables from the alternator.
  5. Raise and support the vehicle.
  6. Release the drive belt tensioner and remove the drive belt from around the alternator.
    NOTE It is not necessary to remove the drive belt from the engine.
  7. Remove the alternator mounting bracket bolts and remove the mounting bracket.
  8. Lower the vehicle.
  9. Remove the power steering pressure hose bracket retaining nut and bolt and remove the bracket with the hose from the engine lifting eye.
  10. Remove the alternator mounting bolts and remove the alternator from the vehicle.
  11. To install:
    1. Place the alternator into position and install the mounting bolts finger tight.
    2. Install the power steering hose bracket and tighten the retaining nut and bolt to 70-106 inch lbs. (8-12 Nm).
    3. Raise and support the vehicle.
    4. Install the alternator mounting bracket and retaining bolts and tighten to 15-22 ft. lbs. (20-30 Nm).
    5. Release the drive belt tensioner and install the drive belt pulley over the alternator pulley.
    6. Lower the vehicle.
    7. Tighten the alternator mounting bolts to 15-22 ft. lbs. (20-30 Nm).
    8. Install the alternator connectors and the cables. Tighten the terminal nut to 80-97 inch lbs. (9-11 Nm).
    9. Install the air cleaner-to-throttle body tube, mass airflow sensor, and the air intake resonators.
    10. Connect the negative battery cable. To install:
      1. Place the alternator into position and install the mounting bolts finger tight.
      2. Install the power steering hose bracket and tighten the retaining nut and bolt to 70-106 inch lbs. (8-12 Nm).
      3. Raise and support the vehicle.
      4. Install the alternator mounting bracket and retaining bolts and tighten to 15-22 ft. lbs. (20-30 Nm).
      5. Release the drive belt tensioner and install the drive belt pulley over the alternator pulley.
      6. Lower the vehicle.
      7. Tighten the alternator mounting bolts to 15-22 ft. lbs. (20-30 Nm).
      8. Install the alternator connectors and the cables. Tighten the terminal nut to 80-97 inch lbs. (9-11 Nm).
      9. Install the air cleaner-to-throttle body tube, mass airflow sensor, and the air intake resonators.
      10. Connect the negative battery cable.


Sep 28, 2009 | 2000 Ford Contour

2 Answers

How do i remove the power steering pump from a 1995 chevy cheyenne 4.3 liter engine? I am trying to replace the pressure side hose on the pump and cannot get to the mounting bolts on the pump because of...


Remove the belt. Using a power steering pump pulley puller, remove the pulley. This will allow you to get to the bolts that hold the bracket. Then just remove the bolts to access the hose. Hope this helps. Good luck.

Jul 26, 2009 | 1995 Chevrolet K1500

1 Answer

I broke timing belt when replacing hormonic balancer


Here are some. Hope it helps =D

Timing Marks

Diagram


TORQUE SPECIFICATIONS
Application Ft. Lbs. (N.m)
A/C Compressor Bracket Bolt 37 (50)
Alternator Bracket Adjuster Bolt 16 (22)
Alternator Bracket Bolt 33 (45)
Balance Shaft Pulley Bolt 22 (30)
Camshaft Pulley Bolt
2.2L DOHC 37 (51)
2.2L SOHC & 2.3L 27 (37)
Crankshaft Pulley Bolt 184 (250)
Power Steering Belt Adjuster Nut 11 (15)
Power Steering Pump Bracket Bolt 33 (45)
Power Steering Pump Mounting Bolt 16 (22)
Shift Cable Bracket Bolt 16 (22)
Timing Belt Tension Adjuster 33 (45)
INCH Lbs. (N.m)
Timing Belt Cover Bolt 108 (12)
Valve Cover Nut 90 (10)
Water Pump Bolt 108 (12)

Jun 28, 2009 | 1992 Honda Accord

2 Answers

Replace alternator


This is for both size engines since you didn't list the motor size......


REMOVAL & INSTALLATION 2.0L Engine
  1. Disconnect the negative battery cable.
  2. Remove air intake resonators.
  3. Remove the air cleaner-to-throttle body tube and the mass airflow sensor.
  4. Unplug the connectors and remove the cables from the alternator.
  5. Raise and support the vehicle.
  6. Release the drive belt tensioner and remove the drive belt from around the alternator. NOTE: It is not necessary to remove the drive belt from the engine.
  7. Remove the alternator mounting bracket bolts and remove the mounting bracket.
  8. Lower the vehicle.
  9. Remove the power steering pressure hose bracket retaining nut and bolt and remove the bracket with the hose from the engine lifting eye.
  10. Remove the alternator mounting bolts and remove the alternator from the vehicle. To install:
  11. Place the alternator into position and install the mounting bolts finger tight.
  12. Install the power steering hose bracket and tighten the retaining nut and bolt to 70–106 inch lbs. (8–12 Nm).
  13. Raise and support the vehicle.
  14. Install the alternator mounting bracket and retaining bolts and tighten to 15–22 ft. lbs. (20–30 Nm).
  15. Release the drive belt tensioner and install the drive belt pulley over the alternator pulley.
  16. Lower the vehicle.
  17. Tighten the alternator mounting bolts to 15–22 ft. lbs. (20–30 Nm).
  18. Install the alternator connectors and the cables. Tighten the terminal nut to 80–97 inch lbs. (9–11 Nm).
  19. Install the air cleaner-to-throttle body tube, mass airflow sensor, and the air intake resonators.
  20. Connect the negative battery cable.

Apr 01, 2009 | 1999 Mercury Mystique

1 Answer

Need to change the alternator


REMOVAL & INSTALLATION

3.3L Engine:
  1. Disconnect the battery negative - cable.
  2. Disconnect the alternator field circuit plug.
  3. Remove the B+ terminal nut and wire.
  4. Loosen the adjusting T-bolt, but do not remove it.
  5. Loosen the pivot bolt, but do not remove it either.
  6. Remove the alternator drive belt.
  7. Remove the adjusting T-bolt, pivot bolt, and mounting bolt, be careful not to loose the spacer.
  8. Remove the mounting bolt.
  9. Remove the spacer & washer
  10. Remove alternator.
To install:
  1. Attachthe alternator to the support bracket. Tighten all bracket andalternator (except for the wiring nuts) bolts to 40 ft. lbs. (54 Nm).Install the B+ terminal nut and wire and tighten to 75 inch lbs. (9 Nm).
  2. Install the drive belt onto the alternator pulley. Make certain that the belt is seated correctly on the pulley.
  3. Connect the negative - battery cable.
-------------------------------------------------------------------------------------------------
3.5L Engine:
  1. Disconnect the negative battery cable.
  2. Loosen the lower mounting bolt but do not remove it.
  3. Loosen the pivot bolt, but do not remove it.
  4. Loosen the belt adjusting bolt.
  5. Remove the alternator drive belt.
  6. Remove the bracket.
  7. Remove the lower mounting bolt and pivot bolt.
  8. Remove the alternator.
  9. Disconnect the alternator field circuit plug.
  10. Remove the B+ terminal nut and wire.
To Install:
  1. Attach the alternator and bracket to the engine, then tighten the mounting bolts to 40 ft. lbs. (54 Nm).
  2. Install the drive belt onto the alternator pulley. Make certain that the belt is seated correctly on the pulley.
  3. Install and tighten the B+ terminal nut and wire to 75 inch lbs. (9 Nm) onto the new alternator.
  4. Connect the alternator field circuit plug.
  5. Connect the negative battery cable.
If you need photos to follow then try this link...
http://www.autozone.com/shopping/repairGuide.htm?pageId=0900c1528006a83e

Jan 20, 2009 | 1999 Dodge Intrepid

Not finding what you are looking for?
1995 GMC Safari Logo

Related Topics:

127 people viewed this question

Ask a Question

Usually answered in minutes!

Top GMC Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Freddy

Level 3 Expert

1311 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Are you a GMC Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...