Question about Nissan Frontier

1 Answer

How do I start if I want to change the water pump in my 2000 Nissan Frontier. 4 cylinder and 4 wheel drive

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Expert
  • 693 Answers

Take out raideator and remember how your surpintine belt go's back on.

Posted on Mar 19, 2011

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do you remove a starter on a 4 wheel drive 2002 Nissan frontier???


How to replace a starter on a 2000 nissan frontier v6 3.3L ...

? 3:14
www.youtube.com/watch?v=ibyIqgGeIug
Jan 6, 2013 - Uploaded by Raul Romo I show how To replace a starter on a 2000 Nissan frontier Part 1. ... and solenoid plug from under the rubber splash guard in thewheel well.

Oct 07, 2015 | 2002 Nissan Frontier Crew Cab

1 Answer

I have a 2000 Nissan Frontier 4x4. One day while driving it just stopped I tried to start it but all it would do is start for a few seconds. And die. I changed fuel filter and started it but would run for...


Could be. Does it sound kind of harsh. Should be a soft whirl sound. Could be the security system. Does the security light stay on? Do you hear the pump running after it starts? You can rent fuel pressure testers from auto parts stores.

Oct 16, 2014 | 2000 Nissan Frontier

1 Answer

2000 frontier 6 cylinder pcv valve location


PO 304-- is a misfire in cylinder # 4

You can Google any codes you get

PCV Valve- if you knew what one was,
has to be on the valve cover, to keep
oil in the crankcase from entering the
induction system

Feb 18, 2013 | 2000 Nissan Frontier

1 Answer

2001 Nissan Frontier REPLACE WATER PUMP - removed Radiator & Hoses Need HELP with REMAINDER


NOTE: When removing water pump assembly, be careful not to get coolant on timing belt unless you intend to replace it. (if it has more than 60.000 miles. it probably SHOULD be replaced, however, you must do it correctly or severe engine damage will occur.)
Drain coolant from drain plugs on both sides of cylinder block and radiator.
Remove radiator hoses (upper and lower) and fan shroud.
Remove drive belts.
Remove water pump pulley.
Remove crankshaft pulley and front (upper and lower) belt cover.
Remove water pump

Oct 01, 2011 | 2001 Nissan Frontier Crew Cab

3 Answers

Where is the fuel pump located on 2000 nissan frontier?


the fuel pump for most vehicles is in the fuel tank.

Mar 09, 2011 | 2000 Nissan Frontier

1 Answer

How to replace oilpump in 2003 nissan frontier. 4 zyl. 4by4 manual shift


hey hit me back in the comments if picts don't load 4L Engine 7924vg43.gif

Align the punch mark with the oil hole before oil pump installation-2.4L engine
Click to Enlarge 7924vg44.gif

Oil pump exploded view-2.4L engine
Click to Enlarge

  1. Before servicing the vehicle, refer to the Precautions Section.

  2. Set the engine to Top Dead Center (TDC) of the compression stroke for the No. 1 cylinder.

  3. Remove or disconnect the following:

    • Distributor cap

    • Distributor

    • Engine under cover

    • Stabilizer bar

    • Oil pump and drive spindle

To install:

  1. Fill the pump housing with engine oil, then align the punch mark on the spindle with the hole in the oil pump as shown.

  2. Install or connect the following:

    • Oil pump and drive spindle. Tighten the mounting bolts to 96-132 inch lbs. (11-15 Nm).reverse procedure on other componets Start the engine and check for leaks.Check the ignition timing and adjust, as necessary.

Dec 12, 2010 | 2000 Nissan Frontier

1 Answer

I installed a oil pump, a destributer cap, rotor, wires and plugs in a 2000 nissan frontier 4 cylinder and now it wont start


You probably inserted the pump wrong. The timing mark on the balancer must be at TDC. Then when you put the pump in, the rotoe should point in the direction of #1 cylinder. If you know that you had these things in order, you probably need to turn the crank one turn. If you set it up with an open valve instead of both valves closed, you are exactly 180° off. Tou can turn the distributor 180° and see if that helps but, it will mess with anyone else that would ever work on it.

Oct 31, 2009 | 2000 Nissan Frontier

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

93 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nissan Experts

yadayada
yadayada

Level 3 Expert

75797 Answers

Phil Lovisek
Phil Lovisek

Level 3 Expert

713 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...