Question about 1989 Ford Ranger

1 Answer

How do i change ignition switch on my 19890 ford ranger xl 4x4 2.9L V6

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 83 Answers

Rotate the lock cylinder to the lock position. On tilt columns, remove upper extension shround by squeezing at 6 and 10 o'clock and popping free of the retainer plate at 3 o'clock.

Remove 2 shroud halves by removing the screws. Disconnect the electrical connector from the ignition switch. Drill out the 2 break-off bolt heads that hold the switch to the lock cylinder using a 1/8" drill bit.

Remove bolts (may have to use a screw extractor). Disengage ignition switch from actuator pin and remove switch.

To Install:
Rotate the key to the run position. Install switch by aligning holes on switch base with hole in the cylinder housing. You may have to move it a little to get the actuator pin to line up.


Install new break-off bolts untill the heads shear off. Connect electrical connector to switch.Then reverse the removal procedure to complete.

Posted on Mar 19, 2011

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Both coils do not fire on 1 and 4. Will start but only running on 2 cylinders. Could both coils be bad or should I look elsewhere?


Part 3 -How to Test the Ignition Module and Crank Sensor ...

easyautodiagnostics.com > Ford > 2.3L
Mar 1, 2012 - Spark plugs for cylinders #2 and #3 get spark at the exact same time. ...voltage -12 Volts) to both individual ignition coils within the coil pack. ... Ford Mustang or Ranger (or 2.3L Mazda B2300), this is what you'll need ... for this 'Switching Signal' at the coil pack... but you can also test this ... 1991, 1992, 1993.

How to Diagnose a Misfiring Cylinder (2.3L Ford Ranger ...

troubleshootmyvehicle.com > Ford > 2.3L
Apr 3, 2012 - Bad Fuel Injectors can cause a Misfire Condition. ... the ignition system on the 2.3L Ford Mustang or Ranger consists of 2 ignition coil packs, ...

2002 ranger misfire rough idle - Discussion on Topix

www.topix.com > Ford Ranger
Jul 27, 2007 - My truck is giving the code misfire in number 4 cyl. I replaced my spark plugs, Wires, Coil packs (both of them) and all my fuil ... three (3.0L v6) go bad, the fuel/air mixture gets messed up. Judged: 2. 2 ... My truck runs rough only at idle. ...code for ford ranger 2002, 2.3 5speed. truck runs like a champ but that ...

Extremely stumped! I need the best and brightest 1994 Ford ...

answers.edmunds.com > Edmunds Answers

Jan 31, 2016 | Cars & Trucks

1 Answer

I HAVE A 1993 FORD RANGER 3.0 V6 ENGINE AND NEED


For 1993 Ford Truck Ranger 4WD 3.0L MFI 6cyl the Control Module-Ignition is located under hood, center, rear engine area, mounted on distributor.

f2a2c92.jpg

Fig. 1: View of the remote mounted Ignition Control Module (ICM)

Hope this help (remember comment and rated this).

Jul 27, 2010 | 1993 Ford Ranger SuperCab

1 Answer

I have a 1984 ford ranger xlt 2.8 v6 manual transmission, I have put a new lock cylinder and new ignition switch but it will not shut off with the key. (carburated)


Sounds like you have a broken ignition lock actuator in the column. You can get these aftermarket. It is a common problem.

Apr 23, 2010 | Ford Ranger Cars & Trucks

1 Answer

Replaced wiring harness on 2000 Ford Ranger now truck won't start


2000 ford ranger wont start off switch if u jump the silanoid it will start. new start and ignition switch

May 06, 2009 | 2000 Ford Ranger SuperCab

1 Answer

1986 ford ranger ready to burn it to the ground


check the ignition switch, they separate and cause this stall out, try holding the ignition to the crank position just short of causing the starter to run, if the engine stays running then the ignition switch is defective, Ford recalled many of these for this problem, not sure your truck was affected, but it does use the sam switch and gets the same problem.

Mar 15, 2009 | 1986 Ford Ranger 2WD

1 Answer

Ignition wiring


firingorder6a.gif firingorder6.gif 1991-1994 2.9L and 3.0L Engines Firing Order 1-4-2-5-3-6 1995 And Later 3.0L V-6 With DIS Ignition System Firing Order 1-4-2-5-3-6
4.0L Engines Firing Order: 1-4-2-5-3-6 DIS Ignition System

Nov 22, 2008 | 1995 Ford Ranger Supercab

1 Answer

85 ford ranger 2.8 v6


Try replacing the ignition module in the distributor. This is a common problem on these engines.

Jun 16, 2008 | 1985 Ford Ranger

Not finding what you are looking for?
Cars & Trucks Logo

759 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

75807 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22133 Answers

fordexpert

Level 3 Expert

5495 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...