Question about 2003 Ford Taurus

1 Answer

How to remove the CV axle There is a roar when driving and believe it is a bearing, how do I fix it. My husband is a good mechanic and can fix it if he has a diagram.

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Ford Master
  • 3,640 Answers

Go to local auto parts store and buy a haynes manual for your car, they are based on a complete teardown of car. this book will show you how. for about 20-25.00.

Posted on Mar 19, 2011

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

What is this roaring sound in the front right axle


If the roaring sound get louder at highway speeds try veering side to side in your lane safely of course to see if the roar noise changes,this would indicate a hub & wheel bearing assembly issue and would need to be replaced.

May 14, 2014 | 2003 Buick Century

1 Answer

How to replace rear bearings in ve commodore


Commodore's are not sold here in the USA. So I'll give it my best shot on two different rear axle setups Since he is mechanically inclined, Look at it. That's what I do before any job. If you have CV axles in back, This is to easy, he will figure it out. Remove the axle nut, remove the bolts for the bearing. Most light duty vehicles are set up like this. Next is the straight axle. You have to remove the differential plate, on most. Remove the bolt to release the center pin.( some others, you have to pry out the axles). Remove the tires, push in on the axles and remove the C clip, pull the axles out. Use a bearing puller or chisel out the bearings. There are different set ups for nissan's and honda's and lexus. These you have to remove the brakes to unbolt the axle to get them out.

Jul 12, 2012 | Holden Cars & Trucks

1 Answer

Honda accord roar, in the front end ,when driving and clickg as i turn sharp


It sounds like you have a bad CV axle, that is the clicking/popping sound you are hearing when you turn, and a bad wheel bearing, that is the roaring sound that you are hearing.

Mar 27, 2011 | 1997 Honda CR-V

1 Answer

I have a 2007 Chevrolet Cobalt. Recently during a snow storm the vehicle went through a ditch. No damage was done to the car. It was the most minute accident ever. Anyways the next day i noticed some noise...


Based on your description, I'm thinking the problem is in the transmission casing. I was thinking it was a wheel bearing, based on your description, but that is contradicted by the fact that you say it doesn't sound like it's a wheel or hub bearing.

You say that the the rf cv axle is now leaking where it goes into the trans. I'd say that's a good place to start looking.

A damaged cv axle or half shaft might make more clicking noises on a tight turn. The cv axle is greased up and has balls inside some designs.

Have you checked the transmission fluid level to see how much fluid has been lost thorugh the place where the cv axle enters the trans.? If adding fluid makes the sound lessen or go away, then the trans. is at fault, vs. the cv axle.

Good luck on this repair.

Jan 16, 2011 | 2007 Chevrolet Cobalt Coupe

2 Answers

1999 Jeep Grand Cherokee 4.0 liter 4wd Front cv drive shafts


yes,they should pull out with a little effort,they have an internal lock ring on the shaft,if they don't pull out you may have to use a pry bar between the inner joint and the case to pry it out.

Apr 29, 2009 | 1999 Jeep Grand Cherokee

1 Answer

Roar from front above 20 mph


Have you checked the wheel bearings in the front, there may be a possibility that the bad cv axle may have caused premature bearing failure and thats where you noise is coming from. Hope this helps.

Feb 01, 2009 | 2003 Chrysler 300M

Not finding what you are looking for?
2003 Ford Taurus Logo

50 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

fordexpert

Level 3 Expert

5501 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...