Question about 1995 Ford Thunderbird

1 Answer

I need a diagram showing how to remove a oil pan off a 1995 Thunderbird

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Scholar:

    An expert who has written 20 answers of more than 400 characters.

  • Expert
  • 83 Answers

Http://www.supermotors.net/getfile/167743/fullsize/oil-pan-sequence.jpg%20alt= what engine do you have in your thunderbird?

Posted on Mar 19, 2011

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do I change my oil pan gasket on my 95 ford Thunderbird, thank you first time car owner


Lift your car and place on jack stands. Then drain engine oil from pan. If there is/are any other steering or suspension components under oil pan, remove these first. Then, begin removing all bolts that hold pan in place. There should be a few bolts that come from the rear of the transmission section that also hold engine oil pan. Remove these. Once all bolts are removed, use a rubber mallet to tap oil pan until is breaks loose. If hard to remove, use a pry bar or flat head screw driver to pry oil pan off. Install in reverse order.

Dec 30, 2016 | Ford Cars & Trucks

1 Answer

How to put new oil pump in 4.6 thunderbird


You will need a service manual (Chilton's Haynes) for all of the correct torque specs and the correct disassembly/assembly sequences. That being said, the oil pump is a big job to change. You will need to disconnect the motor mounts and transmission mounts and raise the engine up so that the oil pan will clear the crossmember. If you can't get clearance doing that, the engine will need to come out. I would check the oil pressure with a mechanical guage to ensure that it indeed as low as it appears to be before beginning the endeavor.

Jun 24, 2011 | 1995 Ford Thunderbird

1 Answer

I have a 95 t-bird and oil leaks in front by the oil pan having to put oil in it once a week could be the gasket around the the oil pan


It could be the oil pan gasket or the front seal behind the harmonic balancer(which is quicker and easier to fix) and it sounds more like the front seal is your issue.

Feb 18, 2011 | 1995 Ford Thunderbird

1 Answer

I need to know how to change the transimission filter on a 1996 ford thunderbird v8. Or at lest where to find a diagram on how to do it


Copied from AutoZone.com:


REMOVAL & INSTALLATION


See Figures 1 and 2
  1. Raise and safely support the vehicle on jackstands.
  2. Place a drain pan under the transmission.
  3. Loosen the pan attaching bolts and drain the fluid from the transmission.

Always place used fluids and oils into a sealed storage container and take to an approved recycling collection facility. Never dump used fluids or oils on the ground or in a trash receptacle. Contamination to the environment can and will occur.
  1. When the fluid has drained to the level of the pan flange, remove the remaining pan bolts working from the rear and both sides of the pan to allow it to drop and drain slowly.

Some AOD transmissions will have a plastic plunger type plug floating loosely in the pan when draining the fluid. It is of no importance and was used in the assembly process of the transmission. Discard it before reinstallation of pan.
  1. When all of the fluid has drained, remove the pan and clean it thoroughly. discard the pan gasket. If equipped, remove the pan magnet.




0900c1528006bc40.jpg enlarge_icon.gifenlarge_tooltip.gif Fig. Fig. 1: Unfasten the remaining bolts, then remove the transmission fluid pan from the vehicle



0900c1528006bc41.jpg enlarge_icon.gifenlarge_tooltip.gif Fig. Fig. 2: On some vehicles, such as this 1995, you must remove and clean the pan magnet
To install:
  1. Place a new gasket on the pan, then install the pan on the transmission. If equipped, don't forget to install the pan magnet. Tighten the pan attaching bolts as follows:

    C3 and C5 Transmissions: 12-16 ft. lbs. (16-22 Nm) A4LD Transmissions: 8-10 ft. lbs. (11-13.5 Nm) AOD Transmissions: 71-119 inch lbs. (8-13 Nm) 4R70W Transmissions: 9-11 ft. lbs. (12-15 Nm)
  2. Add the correct type and quantity of fluid to the transmission through the filler tube.
  3. Lower the vehicle. Start the engine and move the gear selector through shift pattern. Allow the engine to reach normal operating temperature.
  4. Check the transmission fluid. Add fluid, if necessary, to maintain correct level.


FILTER SERVICE


See Figure 3
  1. Remove the transmission oil pan and drain the fluid. For details, please refer to the procedure located earlier in this section.
  2. Remove the screen and the filter from the valve body. Most screens are retained using a fastener; through some may use an interference fit between the screen tube and valve body.




0900c1528006bc42.jpg enlarge_icon.gifenlarge_tooltip.gif Fig. Fig. 3: After the pan is removed, you can remove the transmission fluid filter
To install:
  1. Install a new filter using a new gasket or O-ring.

If the transmission uses a filter equipped with a fully exposed screen, it may be cleaned and reused.
  1. Install the transmission oil pan and properly refill the transmission.

Aug 26, 2010 | 1996 Ford Thunderbird LX

1 Answer

1996 ford T-bird Lx V6 trying to remove timing chain cover to replace gasket ( oil leak above filter housing. All bolts I can see are removed, does the oil filter housing have to be removed also > and...


cover has 2-4 bolts at front of oil pan and harmonic balancer will need to be removed to take cover of of crankshaft.. lemmee kno if that solves your problem...chris..

May 09, 2009 | 1996 Ford Thunderbird LX

1 Answer

I have an oil leak in my 95 thunderbird v8, not the oil pump as far as I can tell, new oil filter, dont think its the sending unit, need a copy of a diagram that shows where all hard lines for oil are...


that has to be transmission fluid is the fluid that is leaking red ?
coming from a tranny cooling line to the radiator.
you motor oil is in your block and held in your oil pan. no where it can leak at that rate except thru the oil sending unit is gone ( missing )
hope2help shack

Apr 18, 2009 | 1995 Ford Thunderbird

1 Answer

I cracked my oil pan and i need to know if i need to take out my engin to change it i'm low on cash i need help


here's v6 3.8L

Section 03-01A: Engine, 3.8L 1996 Thunderbird, Cougar Workshop Manual
IN-VEHICLE SERVICE Oil Pan/Oil Pump Screen Cover and Tube Removal
  1. Disconnect battery ground cable (14301).
  1. Remove air cleaner outlet tube (9B659). Refer to Section 03-12 .
  1. Remove two bolts retaining radiator upper sight shield (8C291) and position radiator upper sight shield aside.
  1. Remove hood weather seal.
  1. Remove windshield wipers.
  1. Remove LH cowl vent screen and wiper module.
  1. Install Three Bar Engine Support D88L-6000-A or equivalent.
  1. Raise vehicle on a hoist. Refer to Section 00-02 .
  1. Remove front engine support insulator through-bolts.
  1. Partially lower vehicle.
  1. Raise engine and support with Three Bar Engine Support D88L-6000-A or equivalent.
  1. Raise vehicle.
  1. Remove starter motor (11002).
  1. Position drain pan.
  1. Drain engine oil.
  1. Remove oil bypass filter (6714).
  1. Remove starter motor wire, ground strap and automatic transmission oil cooler lines.
  1. Remove oil pan-to-bell housing bolts and bolts at crankshaft position sensor lower shield.
  1. Remove remaining oil pan retaining bolts.
  1. Remove steering shaft pinch bolt and separate steering shaft.
  1. Position transmission jack under front sub-frame (5C145).
  1. Remove six rearward bolts on front sub-frame. Loosen two forward front sub-frame bolts.
  1. Remove lower shock absorber-to-front suspension lower arm bolts and nuts (both sides).
  1. Lower front sub-frame.
  1. Remove oil pan (6675).
  1. Empty any residual oil from oil pan.
  1. Remove oil pump screen cover and tube retainer bolts and support bracket nut. Remove oil pump screen cover and tube (6622) and discard oil pump inlet tube gasket (6626).

Apr 14, 2009 | 1996 Ford Thunderbird LX

1 Answer

Oil pan for 1993 thunderbird


No you done have to drop any thing, you just need a new oil pan and gasket for it, loose all bolts around the oil pan and you should be able to remove it, remember remove all the broken off of the old gasket very well before you apply a new one on with grease or gasket cilicon stuff then new oil pan, good luck.

Sep 13, 2008 | 1993 Ford Thunderbird

1 Answer

78 Ford Thunderbird w/ 351 Windsor motor


You'll need to raise the engine to replace the oil pan. Take the trans./converter loose, remove the engine mounts, wiring, fuel line, and anything else that could be a problem with raising the engine. You can use 2 6 x 6's and place under the engine mounts and rest the engine on these. This should provide you with room to drop the pan.

Jun 24, 2008 | Ford Thunderbird Cars & Trucks

Not finding what you are looking for?
1995 Ford Thunderbird Logo

Related Topics:

148 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

75807 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22133 Answers

fordexpert

Level 3 Expert

5495 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...