Question about Dodge Neon

1 Answer

What do you torque the nut at when changing outer tie rod ends on a 2001 dodge neon

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 376 Answers

I usually tighten them hand tight and then tighten it enough to get the cotter pin back in the castle nut and through the cotter pin hole.

Posted on Mar 19, 2011

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What's the outer tie rod end torque specs for 2000 Dodge Dakota sport ?


this was copied off of the following link. should be same torque requirments-
this is off a 2004 manual,which should be real close if not exact

INSTALLATION
1. Align reference marks and install pitman arm.
2. Install the lock washer and retaining nut on the pitman
shaft and tighten nut to 251 N·m (185 ft. lbs.).
3. Install the drag link (1) to the pitman arm (5). Install
the nut (4) and tighten to 54 N·m (40 ft. lbs.) Then
an additional 90°.
4. Remove the supports and lower the vehicle to the
surface. Center steering wheel> and adjust toe,
(Refer to 2 - SUSPENSION/WHEEL ALIGNMENT -
STANDARD PROCEDURE).
5. After adjustment tighten tie rod adjustment sleeve
clamp> bolts to 61 N·m (45 ft. lbs.).
NOTE: Position the clamp on the sleeve so retaining
bolt is located on the bottom side of the
sleeve

got it from here -

Tie rod end torque spec DodgeTalk Dodge Car Forums Dodge Truck Forums and...

Feb 23, 2015 | Dodge Cars & Trucks

1 Answer

Tire rod end left sidefrom gearbox is broken how do i dismantel


if its the outer tie rod than loosen the jam nut on the threaded part of the inner tie rod. You will then be able to unthread the outer tie rod from the inner. Count the number of turns and install the new one with the same number of turns.

If its the inner tie rod you will need an inner tie rode remover/installer tool and a torque wrench.

Feb 03, 2012 | 2001 Mercury Sable

1 Answer

How do i loosen the outer tie rod end to remove it from the bushing once tie rod is out of streeing knuckle i know it will need to be aligined and i need to count treads when putting new outer tie rod end...


You may need a propane torch to heat up the nut on end of outer tie rod. With tie rod still attached to steering knuckle try to loosen the outer tie rod end nut that is connected to inner tie rod. Pull tie rod end back out of knuckle. Use pliers or vise grips to hold inner tie rod end while turning outer tie rod end to the left.

Oct 27, 2010 | Dodge Intrepid Cars & Trucks

1 Answer

How hard is it to replace a outside tie rod end on a 95 dodge neon and how.


take the wheel off, there is a nut on the tie ron locking the tie rod end in place loosen this up (only break it free do not back way off) now take the nut offthe tie rod end that goes into the spindle, Hit the side spindle with a hammer right were the end goes in while pulling up on the tierod end (may take a few hard hits)> Now that you have the end out of the spindle you can unscrew the tie rod end from the inner tierod.*******NOTE*******measure the distance between the locknut on the inner tie rod to the middle of the outer tierod end,You want to keep that same distance or your car will pulll to one side and you'll need a wheel allignment.

Dec 30, 2009 | 1995 Dodge Neon

1 Answer

Repair inner tie rod end of 1997 dodge avenger


f734654.gif #3 is the inner tie rod and it is simply screwed into each end of the steering rack. Raise and support the car remove the wheel and you should see where it is connected to the outer tie rod. There is a lock nut that you'll need to loosen slightly to get the tie rod off. You will need to get a wheel alignment once done but by slightly loosening the lock nut, you have a good reference of how it should be once done. Once loose, you should be able to turn the tie rod by using a wrench on the flattened area on the rod. Once disconnected from the outer tie rod end, you should be able to remove the dust boot covering the inner tie rod connection. Mine came right apart so hope you have no problems. After you have it out, here is where the loosened locknut comes into play. Put the new and old tie rod side by side, line up the ends that attach to the rack and pinion then mark the new rod so you know how far to put the lock nut on the new tie rod. Simply tightly screw the new one onto the rack and pinion put the boot back, screw on the lock nut to the mark then attach the tie rod to the outer tie rod end up to the lock nut then tighten the lock nut against the outer end. Get the tire back on, lower the car and Voila, done. Now go get an alignment.

Nov 18, 2009 | 1997 Dodge Avenger

1 Answer

How do you change outer tierod ends on a 1996 dodge grand caravan


jack vehicle up in front and make sure its secure. remove front wheels. tie rod is bolted thru steering knuckle. remove the cotter pin from tie rod end. remove the nut from tie rod end. use a small ball joint splitter and small sledge to release tie rod end from knuckle. if you dot have splitter a good hard hit with small sledge on steering knuckle where tie rod attaches will usually release it. b careful not to bend backing plate. loosen the lock nut on tie rod and spin old end off. try to install new end as close as possible to same position as old end. you will need a front alignment after replacement.

Oct 03, 2009 | 1996 Dodge Caravan

1 Answer

Need torque spec for 2000 Cirrus outer tie rod ends


45 Ft-lbs Tie-rod balljoint stud-to-steering knuckle nut, and 55 Ft-lbs Tie-rod (outer)- to- inner jam lock nut

Apr 04, 2009 | 2000 Chrysler Cirrus

4 Answers

2001 Dodge Caravan outer tie rod how to install it macking noice and shold i change stiblizar too


loosen nut on tie rod..22mm wrench,remove nut from tie rod end..18mm socket,hit side of knuckle with hammer to seperate tie rod end..unscrew tie rod end from tie rod..reverse procedure to install..you will to hold down on tie rod end to keep stud from spinning

Mar 16, 2009 | 2001 Dodge Caravan

2 Answers

Tie rod problem 98 Dodge


There is a tool that you can use that will make it easier for you. To get to the tie rod end, remove the wheel and take the outer tie rod end loose from the hub. You will have to use a hammer and hit the socket where the end goes into the hub to free it up. Once you have the tie rod loose from the hub, loosen the nut behind the outer tie rod end. Count the revolutions as you unscrew the outer end off and write te number down so you will know how far to put it back on. This will save your alignment. Now, the end that is still there is your inner tie rod end. You will have to undo the bellows boot to get to the nut. The tool will slide over the end and secure onto the nut. Now you just unscrew this and replace with you new inner tie rod end.
Please remember to rate this fix.

Feb 16, 2009 | 1998 Dodge Grand Caravan

2 Answers

Replacing outer tie rod on a 2000 dodge neon


put the tie rod back in and thread the nut on. then you turn the inner tierod with a pipe wrench or a big pair of channel locks. you can spray the threads with pb blaster or wd-40. also if ya have a propane torch this helps loosen the threads. apply heat to the outer tierod do not heat the inner. good luck jimmy

Oct 03, 2008 | 2000 Dodge Neon

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

131 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8195 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...